Omega Vehicle Security DPS3300 manual Model no Description

Page 6

DESCRIPTION

DPS3300 Series instruments are multi-channel scanners that pack a number of functions into one unit. Tasks that require multiple monitors can now be accomplished by using only a single unit. Signals from a number of different transducers can be brought into screw terminals that are conveniently located on the back panel of the instrument. The unit automatically scans through each channel, displaying the channel number and process value. In addition to displaying temperature, pressure, strain, etc. these units also boast some of the most frequently used functions such as process differential between channels, monitoring high and low readings on individual channels, rate of change, tracking channels with highest and lowest readings, comparison of process with a preset set-point, etc.

Signals from thermocouples are linearized and can be displayed in degrees Celsius or Fahrenheit. Transducers that put out 4-20 ma. current loop, 0-5Vdc, or other linear signals can be scaled from the front keys. This gives the flexibility of displaying various parameters directly in engineering units. Channels that do not have signals connected to them may be programmed off by the operator and will not be scanned or displayed.

On power up (check for proper power connections before powering up) the unit will first display 8.8.8.8.8.8.8. as a display test and then the software revision number. The format is 'rEn x.xx' where x.xx is the revision level.

NOTE: Check model number for input type & display units -- thermocouples, 4-20ma, 0-10Vdc etc...

MODEL NO.

 

DESCRIPTION

DPS3304 - (a) - (b) - (c)

4

Channel, fixed input scanner

DPS3314 - (a) - (b) - (c)

4

Channel, programmable input scanner

DPS3307 - (a) - (b) - (c)

7

Channel, fixed input scanner

DPS3317 - (a) - (b) - (c)

7

Channel, programmable input scanner

 

 

 

(a)

INPUT TYPE

(a)

INPUT TYPE

TC

J, K, T or E T /C

C

4-20ma current

R

‘R’ thermocouple

 

 

S

‘S’ thermocouple

 

 

B

‘B’ thermocouple

(a)

INPUT TYPE

RTD

RTD (385, 392)

 

 

TH

Thermistor (400 Series)

V

0-10 volt DC

P

100 millivolt

 

 

 

 

 

 

(b)

POWER

(c)

OUTPUTS

Blank

120VAC Power Input (standard)

5/3

4/7 Relay Outputs (optional)

1

240VAC Power Input (optional)

6/4

4/7 Open Collector Outputs (optional)

2

15Vdc Power Input (optional)

Blank

No Output (standard)

 

 

 

 

Page 5

Image 6
Contents Wall mount Multi-Channel Process Scanner System Configuration SetupChannel Configuration Display ModesDirect Interface to Universal Relay Module Trouble Shooting Table of ContentsPower Input Connector PIN Assignment Error Messages and Solutions MountingSpecifications Page Description Model no DescriptionHow to Display Parameters Displaying ParametersTo Display Perform Following Steps Elapsed Time Mode Mode Function PerformedDisplay Modes Scan Mode High/Low Channel ModeDifference Mode SetupDeviation Mode Types of Deviation DisplaysCH Parameter List SYS Parameter ListSetup For Input Type Channel ConfigurationSetup for Voltage or Current Input Setup For Channel ON/OFFSetup For Offset Setup For High ScaleSetup For Low Scale Setup For TareSetup For Limits Setup For SetpointSetup for Universal Relay Channel 1 Relay Setup For DeadbandTemperature units Setup for Thermocouple/ Thermistor/ RTD InputsSetup For Engineering Units Turning Channels ON/OFFSystem Configuration Setup ExamplesSetup For Display Options Setup for Buzzer Setup For Display TimeSetup For Relay Latch/Non-Latch Setup For Cold Junction CalibrationSetup For Channel Calibration Input Range Setup for current and voltageThermocouple Calibration Procedure Saving Parameter PeaksPage Select Channel Enter PasscodeSYS CH Channel DiffThermistor Elapsed Time IP Type Scan High ChannelLOW Channel Display Devn Channel Diff CR.AL T/C K CurrentOutputs RateLimits Open Collector OptionInput Connector Output Connector Power Input Connector PIN AssignmentDirect Interface to Universal Relay Module Direct Serial Interface toTrouble Shooting Error Messages and SolutionsFactory Channel settings Mounting Slots in Terminal Compartment For Mounting ScrewsWarranty Page M4302/0306