Safety Consideration, Emc | Omega Vehicle Security DPiTH-i16D

START HERE This Quick Start Reference provides information on setting up your instrument for basic operation.

The latest complete Communication and Operational Manual as well as free Software and ActiveX Controls are available at www.omega.com/specs/iseries or on the CD-ROM enclosed with your shipment.

SAFETY CONSIDERATION

This device is marked with the international Caution symbol.

The instrument is a panel mount device protected in accordance with EN61010-1:2001. Remember that the unit has no power-on switch. Building installation should include a switch or circuit-breaker that must be compliant to IEC 947-1 and 947-3.

SAFETY:

•Do not exceed voltage rating on the label located on the top of the instrument housing.

•Always disconnect power before changing signal and power connections.

•Do not use this instrument on a work bench without its case for safety reasons.

•Do not operate this instrument in flammable or explosive atmospheres.

•Do not expose this instrument to rain or moisture.

EMC:

• Whenever EMC is an issue, always use shielded cables.

Disassembly Instruction: If necessary, the unit may be removed from the panel and opened.

Warning: Disconnect all ac power from the unit before proceeding.

1.Make sure the AC power is disconnected.

2.Remove all wiring connections from the rear of the meter. To remove power and input connectors squeeze top and bottom of the case near the connector site for release, then pull connectors from the case.

3.To remove meter from the case, squeeze top and bottom of the bezel to release, then pull from case.

WIRING

Wire the instrument according to the figure shown below.

Warning: Do not connect ac power to your device until you have completed all input and output connections. This device must only be installed by a specially trained electrician with corresponding qualifications. Failure to follow all instructions and warnings may result in injury!

DESCRIPTION OF FRONT PANEL

The upper display may be RH, Temperature or Dewpoint readings depending on your Reading Configuration selections. Factory defaults are shown. The Dual Display allows the user to observe the Relative Humidity or Dewpoint (upper display)

and Temperature Value (lower display), at the same time.

	Relative Humidity	1
	Upper Display	1
	Upper Display	%RH
		2
		D
	Temperature	1
	Temperature
	Lower Display

1	Output 1/Setpoint 1/ Alarm 1 indicator
2	Output 2/Setpoint 2/ Alarm 2 indicator
°C	°C unit indicator for Temperature or Dewpoint
°F	°F unit indicator for Temperature or Dewpoint
%RH	Display shows the Percent Relative Humidity
D	Display shows the Dewpoint
a	Changes display to Configuration Mode and advances
	through menu items*
b	Used in Program Mode:
c	Used in Program Mode:
d	Accesses submenus in Configuration Mode and stores
	selected values*

CONFIGURATION

Button Function in Configuration Mode

•To enter the Menu, the user must first press a button.

a• Use this button to advance/navigate to the next

	MENU	menu item. The user can navigate through all the
	MENU	top level menus by pressing a.
		top level menus by pressing a.

•While a parameter is being modified, press a to escape without saving the parameter.

•Press the up b button to scroll through “flashing” selections. When a numerical value is displayed

bpress this key to increase value of a parameter (UP) that is currently being modified.

•Pressing the b button for approximately 3 seconds will speed up the rate at which the set point value increments.

•In the Run Mode, pressing the b button changes display from RH readings to Temperature readings.

•Press the down c button to go back to a previous Top Level Menu item.

•Press this button twice to reset the controller to the Run Mode.

•When a numerical value is flashing (except set point c value) press c to scroll digits from left to right

(DOWN) allowing the user to select the desired digit to modify.

•	When a setpoint value is displayed press c to
	decrease value of a setpoint that is currently being
	modified. Pressing the c button for approximately
	3 seconds will speed up the rate at which the
	setpoint value is decremented.
•	In the Run Mode, pressing the c button changes

• Never run signal and power wires in the same conduit.

• Use signal wire connections with twisted-pair cables.

• Install Ferrite Bead(s) on signal wire close to the

instrument if EMC problems persist.

MOUNTING

Panel Mounting Instruction:

1.	Using the dimensions from the panel cutout shown in
	exploded views, cut an opening in the panel.
	45mm +.61/-.00square with R 1.5, 4 places
	(1.772”+.024/-.000square with R 0.06”, 4 places)
	Panel thickness: 6.4mm (0.25”) max / 0.8mm (0.03”) min.
2.	Insert the unit into the opening from the front of the panel,
	so the gasket seals between the bezel and the front of the
	panel.

1/4 2/5 3/6

Rear View

BLACK

WHITE

GREEN

RED

SHIELD

N/C

The instrument has two different modes of operation. Run Mode: used to display Temperature and Relative Humidity. Menu Configuration Mode: used to navigate through the menu options and configure the controller.

from RH readings to Dewpoint readings.

• Press the enter d button to access the submenus

from a Top Level Menu item.

d• Press d to store a submenu selection or after ENTER entering a value - the display will flash a STRD

message to confirm your selection.

•In the Run Mode, press d twice to enable Standby Mode with flashing STBY.

3. Slide the retainer over the rear of the case and tighten

against the backside of the mounting panel.

Refer to Operator’s Manual for important Input Probe Shield wiring notes

Connect the main power connections as shown in the figure below

Output 1 and 2 are for -AL Limit Alarm Option only.

FUSE	Connector	Output Type	For 115Vac	For 230Vac	DC
FUSE 1	Output 1	Relay	3 A(T)	3 A(T)	-
FUSE 2	Output 2	Relay	3 A(T)	3 A(T)	-
FUSE 3	Power	N/A	100 mA(T)	100 mA(T)	100 mA(T)
FUSE 4	Power	N/A	N/A	N/A	400 mA(T)

CONFIGURATION

FLOW CHART

HUMd

YES/NO

tEMP

YES/NO

dEU

YES/NO

UNIt

YES/NO


8				8

_____ Underline denotes factory default setup

CNiTH-16D-AL, DPiTH-i16D specifications

The Omega Vehicle Security CNiTH-16D-AL and DPiTH-i16D are two advanced security systems designed to provide comprehensive protection for vehicles. These systems are tailored for car enthusiasts and owners who prioritize safety and want to ensure their vehicles are safeguarded against theft and unauthorized access.

One of the key features of the CNiTH-16D-AL is its integration of a high-performance remote immobilizer. This technology allows users to disable the vehicle's ignition system remotely, preventing the engine from starting unless the correct key fob is in close proximity. This feature not only deters potential thieves but also provides vehicle owners with peace of mind knowing they have control over their vehicle’s access.

The DPiTH-i16D complements the CNiTH-16D-AL with an innovative dual-zone impact sensor. This technology allows the system to differentiate between minor disturbances and significant impacts. When a slight bump is detected, the system can activate a warning alert, while a stronger impact can trigger the alarm. This dual-functionality helps reduce false alarms and ensures the driver is alerted to genuine threats.

Both systems incorporate state-of-the-art encryption protocols, ensuring that communications between the vehicle's key fob and the immobilizer are secure. This feature is pivotal in deterring hacking attempts and protecting against relay attacks, which have become increasingly common in vehicle theft.

Additionally, the Omega Vehicle Security systems are designed to be user-friendly, featuring an intuitive interface and easy installation. The systems come with comprehensive user manuals and support, allowing for a hassle-free integration into various vehicle models, making them versatile in their application.

Another attractive characteristic of these security systems is their compatibility with mobile applications. Users can monitor their vehicles remotely, receive notifications about unauthorized access attempts, and even manage the system from their smartphones. This level of connectivity offers an added layer of convenience and control, allowing owners to stay informed about their vehicle's security status at all times.

In summary, the Omega Vehicle Security CNiTH-16D-AL and DPiTH-i16D represent the pinnacle of vehicle protection. With advanced remote immobilization, dual-zone impact detection, robust encryption, and user-friendly mobile connectivity, these systems provide comprehensive security solutions for modern vehicle owners. Investing in such advanced technology ensures that vehicles remain protected against the evolving threats of theft and unauthorized access, providing long-term peace of mind.