NETGEAR WPN111 user manual Configure the PC network settings, Windows Run program dialog box

Page 33

User Manual for the NETGEAR RangeMax™ Wireless USB 2.0 Adapter WPN111

2.Save your settings in a Profile.

a.Type a descriptive name in the “Profiles” field.

b.Click Save Profile. All the configuration settings are saved in this profile.

c.Click Apply.

d.Click Close to exit the configuration utility.

3.Configure the PC network settings.

a.Configure each PC with either a static IP address or with the IPX protocol.

Note: For instructions on configuring static IP addresses, refer to the networking tutorial on your NETGEAR RangeMax™ Wireless USB 2.0 Adapter WPN111 Resource CD.

b.Restart the PCs.

4.Verify wireless connectivity between your peer devices. Verify connectivity by using the Ping program:

a.On the Windows taskbar click the Start button, and then click Run.

Figure 4-2: Windows Run program dialog box

b.Assuming the target PC is configured with 192.168.0.1 as its IP address, type ping -t 192.168.0.1 and then click OK.

c.This will cause a continuous ping to be sent to the device with the 192.168.0.1 static IP address. The ping response should change to “reply.”

C on figu ra tion

4 -5

202-10076-01

Image 33

Contents NETGEAR, I n c Technical Support FCC Information to User Ta n d a rd s Teste d to C om p lyContents Troubleshooting Index Viii Audience, Scope, Conventions Chapter About This ManualHow to Print this Manual Key Features Chapter IntroductionAbout the WPN111 What’s in the Box? Road Map for ‘How to Get There From Here’Wire le ss On n e ct to a E n tify th e Wire le ss n e tworkWire le ss n etwork To le a rn a b ou t wire le ssVe rify m y n e twork Ca b le or D S L se rvice Twork Ctiva te m yCon n e ction Rovid e rs For you r ve rsion of W in d ows Rowse r su ch a sTwork Con n e ct to th e wire le ss Wire d n etwork Wire le ss a n dE P C I a m u sin g to Igh b orh oodCom b in e d Wire le ss a n d Com p u te r su p p ort grou p sTwork n e e d s to b e D P rin t S h a rin gChapter Basic Setup What You Need Before You BeginVerifying System Requirements Observing Location and Range Guidelines Two Basic Operating ModesBasic Installation Instructions WPN111 Default Wireless Configuration SettingsFor Windows XP Users Installing a WPN111 Click Install Driver and UtilitySta llS h ie ld W iza rd Ort, you V1 typ eIs 1 4 M b p s wh e re a s th e With a W in d ows X P L ogo te stin gSte p s, click th e H e lp b u tton in th e W P N 1 1 Th e se202-10076-01 N 1 1 1 R e sou rce C D Sta llS h ie ld W iza rd For Windows 2000 Users Installing a WPN111Ou n d N e w H a rd wa re W iza rd Sp e e d is 1Ort is 4 8 0 M b p s N 1 1 1 S yste m Tra y I con Tility WPN111 Wireless Connection Indicators Interpreting the LED on the WPN111Or re se t Interpreting System Tray Icon Colors Chapter Configuration Understanding the Configuration OptionsUsing Configuration Profiles Connecting to an Access Point in Infrastructure Mode How to Configure an Infrastructure Mode ProfileRun the WPN111 Configuration Utility Save your settings in a Profile Configure the wireless Network settingsConnecting to Another PC in Ad-hoc Mode How to Configure an Ad-hoc Mode ProfileVerify wireless connectivity to your network Windows Run program dialog box Configure the PC network settingsPing test results How to Start a Computer-to-Computer Ad-Hoc NetworkEnabling Wireless Security Features Configure the Security settings How to Configure WEP Encryption SecurityHow to Configure WPA-PSK Encryption Security Advanced Security StatisticsAdvanced Settings Advanced Settings202-10076-01 Basic Tips Chapter TroubleshootingGeneral Questions Frequently Asked QuestionsNew Hardware Wizard appears after installation has completed Rou b le s h ootin g Appendix a Technical Specifications Ch n ica l S p e cifica tion s Appendix B Wireless Networking Basics Wireless Networking OverviewInfrastructure Mode Ad Hoc Mode Peer-to-Peer Workgroup Network Name Extended Service Set Identification EssidWireless Channels 802.11b/g Wireless Channels For U S Re qu e n cy G H z 5 5 2 5 5 2For C a n a d a W for E u rop eWPN111 user can use thirteen channels in non-turbomode Wireless Security Overview 152160 WEP Overview WEP Authentication802.1x Cisco LeapAuthentication Open System Steps Bit WEP WEP KeysWEP Key Configuration How to Use WEP Parameters802.1x Port Based Network Access Control Figure B-4 802.1x authentication WPA Wireless Security How Does WPA Compare to WEP? How Does WPA Compare to Ieee 802.11i? What are the Key Features of WPA Security?Figure B-5 WPA Overview Figure B-6 WPA/802.1x Authentication Sequence 202-10076-01 WPA Data Encryption Key Management Temporal Key Integrity Protocol TkipMichael Is WPA Perfect? Product Support for WPAAES Support Wireless network adapters Wireless client programs 202-10076-01 Configuring Windows 98 and Me for TCP/IP Networking Appendix C Preparing Your PCs for Network AccessInstall or Verify Windows Networking Components Preparing Your Computers for TCP/IP NetworkingRe p a rin g Y ou r P C s for N e twork a cce ss Choose Settings, and then Control Panel Enabling Dhcp in Windows 98 and MeLocate your Network Neighborhood icon Primary Network Logon is set to Windows logon Verifying TCP/IP Properties Selecting Windows’ Internet Access MethodConfiguring Windows 2000 or XP for TCP/IP Networking Dhcp Configuration of TCP/IP in Windows XP Dhcp Configuration of TCP/IP in Windows XP orTCP/IP details are presented on Support tab Verify that Obtain an IP address Dhcp Configuration of TCP/IP in WindowsObtain an IP address automatically is selected Verifying TCP/IP Properties for Windows XP or 202-10076-01 Glossary DSL Internet service provider Ssid Wins 202-10076-01 Numerics Index

Related manuals

Manual 87 pages 60.77 Kb