NETGEAR WG111 user manual Glossary

Page 71

Glossary

Use the list below to find definitions for technical terms used in this manual.

10BASE-T

IEEE 802.3 specification for 10 Mbps Ethernet over twisted pair wiring.

100BASE-Tx

IEEE 802.3 specification for 100 Mbps Ethernet over twisted pair wiring.

802.11b

IEEE specification for wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.5GHz.

802.11g

An IEEE specification for wireless networking at 54 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.5GHz. 802.11g is backwards compatible with 802.11b.

ADSL

Short for asymmetric digital subscriber line, a technology that allows data to be sent over existing copper telephone lines at data rates of from 1.5 to 9 Mbps when receiving data (known as the downstream rate) and from 16 to 640 Kbps when sending data (known as the upstream rate).

ADSL requires a special ADSL modem. ADSL is growing in popularity as more areas around the world gain access.

DHCP

An Ethernet protocol specifying how a centralized DHCP server can assign network configuration information to multiple DHCP clients. The assigned information includes IP addresses, DNS addresses, and gateway (router) addresses.

DNS

Short for Domain Name System (or Service), an Internet service that translates domain names into IP addresses.

Because domain names are alphabetic, they're easier to remember. The Internet however, is really based on IP addresses. Every time you use a domain name, therefore, a DNS service must translate the name into the corresponding IP address. For example, the domain name www.example.com might translate to 198.105.232.4. The DNS system is, in fact, its own network. If one DNS server doesn't know how to translate a particular domain name, it asks another one, and so on, until the correct IP address is returned.

Glossary

1

202-10026-01

Image 71
Contents 202-10026-01 Vcci Statement Certificate of the Manufacturer/ImporterFCC Requirements for Operation in the United States FCC Guidelines for Human ExposureDeclaration Of Conformity Netgear 54 Mbps Wireless USB 2.0 Adapter WG111 Operation Using 2.4 GHz Channels in FranceMetropolitan Regions with Eased Restrictions in 2.4GHz Band 202-10026-01 Contents Appendix C Preparing Your PCs for Network Access Glossary Index Contents Typographical conventions Manual SpecificationsChapter About This Manual Audience, Scope, ConventionsHtml version of this manual How to Use this ManualHow to Print this Manual About This Manual About the WG111 Key FeaturesChapter Introduction What’s in the Box? Road Map for ‘How to Get There From Here’If I Want To? What Do I Do? What’s Needed? How Do I? Road Map for How to Get There From HereNetgear 54 Mbps Exchange files Use printers Verifying System Requirements Chapter Basic SetupWhat You Need Before You Begin Observing Location and Range Guidelines Two Basic Operating ModesWG111 Default Wireless Configuration Settings Basic Installation Instructions Install the WG111 driver and configuration utility software For Windows XP Users Installing a WG111Install the Netgear 54 Mbps Wireless USB 2.0 Adapter WG111 Configure your WG111 Verify wireless connectivity to your network Click Install Driver and Utility For Windows 2000 & 98/Me Users Installing a WG111Found New Hardware Wizard WG111 System Tray Icon Profile Configure your WG111 and saveVerify wireless connectivity to your network LED Descriptions WG111 Wireless Connection IndicatorsInterpreting the LED on the WG111 Yellow TroubleshootingInterpreting System Tray Icon Colors RedBasic Tips Troubleshooting Frequently Asked QuestionsBasic Setup Basic Setup Basic Setup Using Configuration Profiles Chapter ConfigurationUnderstanding the Configuration Options Configure the wireless Network settings Connecting to an Access Point in Infrastructure ModeHow to Configure an Infrastructure Mode Profile Run the WG111 Configuration UtilityHow to Configure an Ad-hoc Mode Profile Connecting to Another PC in Ad-hoc ModeWindows Run program dialog box Configure the PC network settingsPing test results How to Start a Computer-to-Computer Ad-Hoc Network Enabling Wireless Security FeaturesConfigure the Security settings How to Configure WEP Encryption SecuritySave your settings in a Profile Statistics Advanced SettingsConfiguration USB Appendix a Technical SpecificationsTechnical Specifications Infrastructure Mode Appendix B Wireless Networking BasicsWireless Networking Overview Network Name Extended Service Set Identification Essid Authentication and WEPAd Hoc Mode Peer-to-Peer Workgroup Open System Authentication AuthenticationAuthentication Open System Steps Do Not Use WEP Authentication Shared Key StepsKey Size WEP Configuration OptionsWireless Channels 802.11b and g Radio Frequency Channels Radio frequency channels used are listed in TablePreparing Your Computers for TCP/IP Networking Appendix C Preparing Your PCs for Network AccessConfiguring Windows 98 and Me for TCP/IP Networking Install or Verify Windows Networking ComponentsPreparing Your PCs for Network Access Locate your Network Neighborhood icon Choose Settings, and then Control PanelEnabling Dhcp in Windows 98 and Me Primary Network Logon is set to Windows logon Verifying TCP/IP Properties Selecting Windows’ Internet Access MethodConfiguring Windows 2000 or XP for TCP/IP Networking Dhcp Configuration of TCP/IP in Windows XP Dhcp Configuration of TCP/IP in Windows XP orTCP/IP details are presented on Support tab Right click on Local Area Connection and select Properties Dhcp Configuration of TCP/IP in WindowsVerify that Obtain an IP address Obtain an IP address automatically is selected Verifying TCP/IP Properties for Windows XP or Preparing Your PCs for Network Access Glossary DSL Internet service provider Ssid Wins Glossary Numerics Index