Clarion DRX9575Rz Basic Operations, Changing the angle of the Sloping Console, Adjusting the tone

Basic Operations

∗The spectrum analyzer display is only displayed when the DPH7500z is connected.

∗Once selected, the preferred display becomes the display default. When a function adjustment such as volume is made, the screen will momentarily switch to that function’s display, then revert back to the preferred display sev- eral seconds after the adjustment.

∗If a title has been input, it is displayed in the main display. If no title has been input, “------------” appears in the display. To input a title, refer to the subsection in “Entering titles” in “Other Handy Functions” section.

Changing the angle of the SLOPING CONSOLE

If the installation position or display angle makes the display hard to see, change the angle of the

SLOPING CONSOLE.

1.Press A button 7.

2.Each time this button is pressed, the SLOP- ING CONSOLE switches to the tilted or closed state.

CAUTION

When not using this unit for a long time and when turning OFF the ignition key for the car, close the SLOPING CONSOLE for safety’s sake.

Switching the screen saver

You can switch between 2 screen savers.

1.Press DISP button " and select the screen saver display.

2.Each time you press and hold DISP button " for 1 second or longer, the screen saver changes between 2 screen savers.

Setting the Z-enhancer

This unit comes with 3 types of sound tone effect stored in memory. Select the one you prefer.

∗The factory default setting is “Z-EHCR OFF”. Each time you press Z-EHCR button 8, the tone effect changes in the following order:

“Z-EHCR 1” ➜ “Z-EHCR 2” ➜ “Z-EHCR 3” ➜ “Z-

EHCR OFF” ➜ “Z-EHCR 1”...

When a Z-enhancer comes on (1-3), “Z-EHCR” lights in the display.

•Z-enhancer 1:

Setting emphasizing bass

•Z-enhancer 2:

Setting emphasizing treble

•Z-enhancer 3:

Setting emphasizing bass and treble

•OFF:

Neither bass nor treble emphasized by Z-enhancer

Adjusting the tone

Press A-M button % and select the item to ad- just. Each time you press A-M button %, the item changes in the following order:

●When the Z-enhancer and tone bypass are off

“NON-FADER VOL” ➜ “TONE BYPASS” ➜

“SOUND” ➜ “POSITION” ➜ Function mode...

●When Z-enhancer 1, 2 or 3 is set

“NON-FADER VOL” ➜ “Z-ENHANCER”➜

“POSITION” ➜ Function mode...

Note:

•When the separately-sold digital sound processor (DPH7500z) is used, the tone bypass, bass and treble tone adjustments cannot be selected. To adjust the tone, see the chapter “DSP Operations”.

Adjusting the non-fader output volume

You can adjust the volume output from the unit’s non-fader output terminal.

1.Press A-M button % and select “NON-FADER VOL”.

2.Turning the Rotary knob 3 clockwise increases the output volume; turning it counterclockwise decreases the output volume.

∗The factory default setting is “4”. (Setting range: 0 to 7)

3.When the adjustment is complete, press A-M button % several times until the function mode is reached.

Setting tone bypass

The tone bypass disables the tone (bass and treble) functions and cuts the noise generated when the tone functions are on.

1.Press A-M button % and select “TONE BYPASS”.

2.Turning the Rotary knob 3 clockwise sets the tone bypass to “YES” (ON); turning it counterclockwise sets the tone bypass to “NO” (OFF).

∗The factory default setting is “NO” (OFF).

∗If the setting is “YES” (ON), the bass and treble adjustments cannot be made.

3.When the adjustment is complete, press A-M button % several times until the function mode is reached.

Note:

•If a Z-enhancer (1-3) is ON, tone bypass cannot be set.

DRX9575Rz 11