NETGEAR FS 726, FS 750 manual Index

Page 50

A

Applications

Desktop Switching, 3-1 Segment Switching and Bridging

from Mbps to 100 Mbps, 3-2 Applying AC Power, 4-6

Auto Uplink, 2-5

C

Cabling guidelines

Fast Ethernet Cable Guidelines, C-1 Category 5 Cable, C-2

Category 5 Cable Specifications, C-3 Twisted Pair Cables, C-3

Patch Panels and Cables, C-5

Using 1000BASE-T Gigabit Ethernet over Category 5 Cable, C-5

Cabling, C-6

Length, C-6

Return Loss, C-6

Near End Cross Talk (NEXT), C-7 Patch Cables, C-7

Conclusion, C-7 Checking the Installation, 4-6 Connecting Devices to the Switch, 4-4 Connector pin assignments

RJ-45 Plug and RJ-45 Connector, B-1 Customer Support, iv

D

Data Rate, A-1

Desktop Switching, 3-1

F

Fast Ethernet Cable Guidelines, C-1

Features, 1-2

Front and Back Panels, 2-1

Fiber Optic Cables, C-8

Fiber Cable Specifications, C-8

G

Gigabit Cable Guidelines, C-8

I

Installation

Preparing the Site, 4-2

Installing the Switch, 4-3

Installing the Switch on a

Flat Surface, 4-3

Installing the Switch in a Rack, 4-3 Connecting Devices to the Switch, 4-4 Checking the Installation, 4-6 Applying AC Power, 4-6

Interface, A-1

L

LED Descriptions, 2-4

N

Near End Cross Talk (NEXT), C-7 Network Protocol and

Standards Compatibility, A-1

index I-1

Image 50

Contents Modular Fast Ethernet Switch Certificate of the Manufacturer/Importer TrademarksStatement of Conditions Voluntary Control Council for Interference Vcci StatementEN 55024 Declaration of Conformity IiiCustomer Support Internet/World Wide WebContents Connector Pin Assignments Troubleshooting InformationTechnical Specifications Appendix C Cabling GuidelinesTables Tables Introduction IntroductionDescription Key Features FeaturesKey Features Additional Features Introduction Package Contents Physical Description Front and Back PanelsFront and Back Panels of the FS726 Switch Front and Back Panels of the FS750 Switch 10/100 Mbps RJ-45 PortsLED Mode Button and LED Descriptions Front Panel LEDsModule Bays Auto UplinkCreating Redundant Paths between Network Devices Example Reset Button Desktop Switching ApplicationsSegment Switching and Bridging from 10 Mbps to 100 Mbps Media Compatibility and ConversionExample of Media Compatibility and Conversion Applications Installation InstallationCharacteristics Requirements Preparing the SiteInstalling the Switch in a Rack Installing the SwitchInstalling the Switch on a Flat Surface Connecting Devices to the Switch Connecting Devices to the Switch InstallationUsing Gigabit Ethernet Modules Checking the Installation Applying AC PowerInstallation Troubleshooting Chart TroubleshootingTroubleshooting Chart TroubleshootingTo is powered on and operating Switch Integrity Additional Troubleshooting SuggestionsConfiguration Network Adapter CardsData Rate Appendix a Technical SpecificationsNetwork Protocol and Standards Compatibility InterfacePerformance Specifications FS726 FS750Physical Specifications FS726 Environmental SpecificationsElectromagnetic Susceptibility Safety Agency ApprovalsElectromagnetic Emissions Appendix B Connector PIN Assignments RJ-45 Plug and RJ-45 Connector100/1000 Mbps RJ-45 Plug and RJ-45 Connector Pin Assignments Duplex SC Plug and Duplex SC Connector Cabling guidelines Appendix C Cabling GuidelinesFast Ethernet Cable Guidelines Category 5 Cable Table C-1. Electrical Requirements of Category 5 Cable Category 5 Cable SpecificationsTwisted Pair Cables Figure C-1 illustrates straight-through twisted pair cable Patch Panels and Cables Return Loss CablingLength Conclusion Near End Cross Talk NextPatch Cables Gigabit Cable Guidelines Fiber Cable SpecificationsFiber Optic Cables Table C-2. Electrical Requirements of Fiber Optic CableIndex Index NETGEAR, Inc