NetComm NB1300PLUS4 manual Atm, Where can I download the free software to test Igmp

Page 46

Advanced

ATM:

Service Category: UBR and CBR are supported from the ATM.

Bandwidth: Bandwidth setting takes effect only when the CBR is selected. The maximum available bandwidth is from the upstream data rate of ADSL status page.

Encapsulation: Bridge IGMP

IGMP relay/proxy specification and environment: Support IGMP proxy/relay function for ADSL modem, based on the following requirement and case:

On CO side, there must be at least one IGMP querier (router) present. IGMP querier will send IGMP query packet. The ADSL modem is responsible to relay these IGMP query to Ethernet.

End-user multicast application device send IGMP report while receiving IGMP query or being activated by user, the ADSL modem should be responsible to proxy (that is, change source IP to ADSL modem's WAN IP) the IGMP report to ADSL WAN side, include all PVCs. The same case is for IGMP leave packet.

Not necessary to relay multicast routing between two ADSL PVCs or two interfaces in LAN side.

Special purpose multicast packet (such as RIP 2 packet) should run without interference.

Note: Before the IGMP mode is enabled; please go to the Miscellaneous Configuration page to enable the IGMP proxy. Otherwise, the IGMP selection will not be valid.

Q: Where can I download the free software to test IGMP.

A:Please go to this link http://manimac.itd.nrl.navy.mil/MGEN/.

PPP:The current release supports multiple PPP sessions per PVC. The PPP configuration in the WAN configuration page is for the first PPP session for each PVC. The predefined PPP Account Name (Account ID) is "Simple PPP Account 0" for PVC0 and predefined PPP Connection Name is "Simple PPP Session 0" for PVC0. For the other PVC X, the predefined account name and connection name will be Simple PPP Account X and Simple PPP Session X. X is the PVC number from 1 to 7.

It can support up to total of 16 PPP sessions, and each PVC can support up to 8 PPP sessions. The multiple PPP sessions may be configured with any combination over 8 PVCs. For the multiple PPP sessions, please go to PPP Configuration page (Section 6.3).

Service Name: The service name of PPP is required by some ISPs. If the ISP does not provide the Service Name, please leave it blank.

Disconnect Timeout: The Disconnect Timeout allows the user to set the specific period of time to disconnect from the ISP. The default is 0, which means never disconnect from the ISP.

DHCP Client: Use Table 6-1 to configure a valid setting for each PVC.

MRU: Maximum Receive Unit indicates the peer of PPP connection the maximum size of the PPP information field this device can be received. The default value is 1492 and is used in the beginning of the PPP negotiation. In the normal negotiation, the peer will accept this MRU and will not send packet with information field larger than this value.

www.netcomm.com.au

Rev. 1- YML674

Page 46

NB1300Plus4 ADSL Modem

Image 46
Contents Page Contents Adsl LAN WAN ATM Package Contents OverviewConnecting your NB1300Plus4 Connecting your NB1300Plus4 Adsl Modem via EthernetConnecting your NB1300Plus4 Adsl Modem via USB Do I need a Micro filter? LED Indicators PWRUsing Easy Config Loading an ISP profile into your NB1300Plus4Overview Resetting to factory defaults Factory DefaultsField Setting Details Configuration Types Adsl Modem Ethernet Configuration Adsl Modem EthernetConnecting your computer to the NB1300Plus4 Configuring the NB1300Plus4 Second Router Method Operational Diagram for Adsl Modem Configuration Adsl Modem USB Configuration Adsl Modem USBConnecting your computer to the NB1300Plus4 Configuring the NB1300Plus4 Configuring your Computer/Router to use the NB1300Plus4 Operational Diagram for Adsl Modem Configuration Adsl Gateway Router Ethernet Configuration Router EthernetAdsl Router Ethernet Configuring your Computer to use the NB1300Plus4 Adsl RouterAdsl Gateway Router Ethernet Operational Diagram for Ethernet Gateway Configuration Adsl Gateway Router USB Configuration Adsl Gateway Router USB Configuring the NB1300Plus4 VPI Operational Diagram for USB Gateway Configuration Macintosh OS X USB Configuration Macintosh USBMacintosh USB Macintosh USB Multiple Virtual Circuits How to make changesUSB or Ethernet? Main Menu Simple One Page Setup Basic MenuShow Advanced Settings StatusRouter WANAdsl PPP Main Menu Advanced One Page Setup Hide Advanced settingsAdministration Where can I download the free software to test Igmp ATMWhen should I change my MTU settings? What should I change my MTU settings to?LAN/DHCP DNS NAT Advanced Port Forwarding Adsl Configuration RIP Configuration Diagnostic Test Route Table MAC Filtering Security Admin Password User Password Misc Configuration Advanced System Log Advanced Code Update Status Router Adsl LAN WAN Status page shows the information and status of WAN PVCs ATM TCP Connections Learned MAC Table PPP Save Settings and Reboot Appendix a Connection Instructions Connect your NB1300Plus4 Adsl Modem via EthernetConnect your NB1300Plus4 Adsl Modem via USB Macintosh OS X USB Configuration Rev YML674 NB1300Plus4 Adsl Modem Rev YML674 General Modem Operation Correct power up sequenceResetting the NB1300Plus4 Adsl Modem PWR LED Not OnWeb Based Interface Adsl link Internet / ISP ConnectionObtaining a WAN IP Address PPPoE or PPPoA Internet BrowsingTesting your TCP/IP Network Using a Ping Utility Testing the LAN Path to Your Adsl ModemTesting the Path from Your Computer to a Remote Device Ping -n 10 IP addressAppendix C Glossary LAN UBR Contact Information Trademarks and NoticesWarranty Registration Form Page Product Warranty Limitations of Warranty