NetComm NB712 manual Username, Password Confirm, Idle Time

Page 30

Type the ISP1 parameters.

 

Username:

test

Password:

test

Password Confirm:

test

 

Your ISP will provide the user name and password.

Idle Time:

10

 

If you want your Internet connection to remain on at all

 

times, enter 0 in the Idle Time field.

IP Type:

There are three IP types, Dynamic, Fixed and IP

 

Unnumbered, which you can setup. The default IP type

 

is Dynamic. It means that ISP PPP server will provide IP

 

information including a dynamic IP address when a SHDSL

 

connection is established. I.e. you do not need to type the IP

 

address of WAN1. Some ISPs will provide fixed IP address

 

over PPP.

For fixed IP address:

 

IP Type:

Fixed

IP Address:

192.168.1.1

Click Next.

 

For IP Unnumbered:

 

IP Type:

IP Unnumbered

IP Address:

192.168.168.1

Click Next.

 

30

NB712 / NB714 User Guide

 

YML829 Rev1

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Page Contents NB714 User Guide Features Package ContentsIntroduction Bridging SpecificationRouting SecurityAAL5 Encapsulation IndicatorsATM QoS WAN InterfaceMemory ApplicationPhysical/Electrical Product InformationFirewall Types of Firewall Packet FilteringThere are three types of firewall Denial of Service Attack Circuit GatewayApplication Gateway Icmp Flood Ping of deathSYN Flood UDP FloodVlan Virtual Local Area Network Frame SpecificationApplications VID uniquely identifies the Vlan to which the frame belongsGetting to know the router Front PanelLED status Rear Panel LAN 1,2,3,4Determine Connection Setting Connecting your G.SHDSL Modem RouterCheck the Terminal Access Program Check the Ethernet Adapter in PCBridge EoA Route EoA IPoA PPPoA Cross-over Ethernet cables can be used Install the Shdsl RouterPPPoE Port router with network topologyConfiguration via Web Browser Router, which will lose any previous configuration Basic Setup System error or disconnectionClick Basic for basic installation Bridge Mode LAN ParametersEnter Host Name WAN1 Parameters Enter VPI Enter VCI Click LLC Click NextRouting Mode Click Next to setup WAN1 parameters Dhcp ClientLAN IP Type IP Address Dhcp ServerIP type Subnet MaskTrigger Dhcp Service DNS ServerDhcp relay RelayProtocol PPPoE or PPPoAAAL5 Encap For more information, refer to the section on NAT/DMZUsername PasswordPassword Confirm Idle TimeEprom IPoA or EoA GatewayEprom Advanced Setup Data rate Annex TypeLink Type Data RateMargin, the better the line connection Shdsl SNR marginMargin range is from 0 to Reconnect for better line connectionWAN CBR Constant Bit Rate QoS Quality of ServiceUBR Unspecified Bit Rate PCR Peak Cell Rate in kbpsBridge Eprom Vlan Pvid PacketsAuto RIP Summary RIP ModeRoute Press ModifyAuthentication required RIP VersionPoison Reverse NAT/DMZ Virtual Start IP Address Multi-DMZMulti-NAT Count Global Start IP AddressVirtual Server Firewall Basic Firewall SecurityAutomatic Firewall Security SYN Attack Advanced Firewall SecurityClick Advanced Firewall Security and then press Finish Connections and will be unresponsiveAddresses originating from your network Ping of death attack attempts to crash your system bySrc. IP Address DirectionDescription Dest. IP AddressFiltering Rule for Smtp connection Filtering rule will be configured as followUpdate Filtering Rule Filtering ResultWhen the rule is ordered as ABC Rule Order10.0.0.0 172.16.6.0 Permit 10.1.99.0 172.16.0.0 Deny Any IP QoS NB714 User Guide Administration Security NB712 / NB714 User Guide Snmp MIBSnmp status CommunityVersion Community Time Sync Click on Time SyncSntp service Time ServerTime Zone Utility System Info 10.2 Config Tool Restore ConfigurationBackup Configuration Lose all the configured parametersUpgrade Logout To logout the router, press logoutRestart Status You can monitor the followingLAN-to-LAN connection with bridge Mode CO sideLAN Parameters Enter Gateway 192.168.1.1 Enter Host Name WAN1 ParametersEnter IP 192.168.1.1 Enter Subnet Mask Enter VPI Enter VCI EncapCPE Side Host Name Enter SohoVCI32 EncapLLC Click Route and CO Side then press Next LAN to LAN Connection with Routing ModeDhcp Service IP Address 192.168.20.1 Subnet Mask 255.255.255.0 Host NameClick Next to setup the IP parameters WAN ParametersClick Route and CPE Side then press Next IP Address 192.168.10.1 Subnet Mask 255.255.255.0 Host Name192.168.30.2 Telnet Useradmin PasswordSerial Console Baudrate 9600 Data Bits Parity Check Stop Bits Flow-controlOperation Interface Window structure Menu Driven Interface Commands To choose another parametersCtrl + C To quit the configuring item Ctrl + Q For help Menu Tree 14.7 Configuration Utility Ping Packet internet groper command AdminDone via utility command Exit Quit systemStatus Config ShowSystem ScriptWrite RebootAdministration PingUser Profile Snmp Edit Community Entry List ShowSupervisor Password and ID Move the cursor to sntp and press enter Move the cursor to service and press enterSntp Move the cursor to timeserver1 and press enterMove the cursor to list and review the setting Exit SetupUtility ModeShdsl 14.16.3 WAN Bridge After enter add menu, the screen will prompt as followVlan Move the cursor to vlan and press enter14.16.6 802.11Q Vlan Follow the following steps to configure 802.11q VlanFor each VLAN, Vlan ID is a unique number among 1~4095 Route Generic command can setup RIP mode and auto summery modeYou can review the list of RIP parameters via list command Screen will display the following14.16.8 LAN IP share14.16.10 NAT You can configure NAT parameters in nat menuMapping 14.16.11 PAT After key in enter, the screen will prompt as below14.16.12 DMZ You can enable the demilitarized zone via active commandfirewall security level can configure via level command FirewallActive DoS Protection IPQoS You can view the Dhcp configuration via list command DhcpDefault DNS proxyHost name 10Mbps Appendix a Cable InformationRJ-45 Network Ports 100MbpsStraight and crossover cable configuration Straight-Through CablingCross-Over Cabling RxD O Shdsl Line Connector Console CableNo connection TxDAppendix B Registration and Warranty Information Contact InformationProduct Warranty
Top Page Image Contents