NetComm NB712 manual Utility, Exit, Setup, Mode, Move the cursor to utility and press enter

Page 95

14.14 Utility

There are three utility tools, upgrade, backup and restore, embedded in the firmware. You can update the new firmware via TFTP upgrade tools and backup the configuration via TFTP backup tool and restore the configuration via TFTP restore tool. For upgrade, TFTP server with the new firmware will be supported by supplier but for backup and restore, you must have your own TFTP server to backup and restore the file.

Move the cursor “ >> “ to utility and press enter.

>>upgrade

Upgrade main software backup

Backup system configuration Restore

Restore system configuration

14.15 Exit

If you want to exit the system without saving, use exit command to quit system.

14.16 Setup

All of the setup parameters are located in the subdirectories of setup. Move the cursor “ >> “ to setup and press enter.

>> mode

Switch system operation mode

shdsl

Configure SHDSL parameters

wan

Configure WAN interface profile

bridge

Configure transparent bridging

vlan

Configure virtual LAN paramters

route

Configure routing parameters

lan

Configure LAN interface profile

ip_share

Configure NAT/PAT parameters

firewall

Configure Firewall parameters

dhcp

Configure DHCP parameters

dns_proxy

Configure DNS proxy parameters

hostname

Configure local host name

default

Restore factory default setting

14.16.1 Mode

The product can act as routing mode or bridging mode. The default setting is routing mode. You can change the system operation mode by using mode command. Move the cursor “ >> “ to mode and press enter.

----------------------------------------------------------------------

Command: setup mode <RouteBridge>

Message: Please input the following information.

System operation mode (TAB select) <Route>: Route

----------------------------------------------------------------------

NB712 /

NB714 User Guide

95

YML829

Rev1

 

Page 94 Page 96
Image 95
Page 94 Page 96
Contents Page Contents NB714 User Guide Introduction FeaturesPackage Contents Security SpecificationRouting BridgingWAN Interface IndicatorsATM QoS AAL5 EncapsulationProduct Information ApplicationPhysical/Electrical MemoryFirewall There are three types of firewall Types of FirewallPacket Filtering Application Gateway Denial of Service AttackCircuit Gateway UDP Flood Ping of deathSYN Flood Icmp FloodFrame Specification Vlan Virtual Local Area NetworkVID uniquely identifies the Vlan to which the frame belongs ApplicationsLED status Getting to know the routerFront Panel LAN 1,2,3,4 Rear PanelCheck the Ethernet Adapter in PC Connecting your G.SHDSL Modem RouterCheck the Terminal Access Program Determine Connection SettingBridge EoA Route EoA IPoA PPPoA Port router with network topology Install the Shdsl RouterPPPoE Cross-over Ethernet cables can be usedConfiguration via Web Browser Router, which will lose any previous configuration Click Basic for basic installation Basic SetupSystem error or disconnection Enter Host Name Bridge ModeLAN Parameters Enter VPI Enter VCI Click LLC Click Next WAN1 ParametersRouting Mode LAN IP Type Click Next to setup WAN1 parametersDhcp Client Subnet Mask Dhcp ServerIP type IP AddressDNS Server Trigger Dhcp ServiceRelay Dhcp relayFor more information, refer to the section on NAT/DMZ PPPoE or PPPoAAAL5 Encap ProtocolIdle Time PasswordPassword Confirm UsernameEprom Gateway IPoA or EoAEprom Advanced Setup Data Rate Annex TypeLink Type Data rateReconnect for better line connection Shdsl SNR marginMargin range is from 0 to Margin, the better the line connectionWAN PCR Peak Cell Rate in kbps QoS Quality of ServiceUBR Unspecified Bit Rate CBR Constant Bit RateBridge Eprom Vlan Packets PvidPress Modify RIP ModeRoute Auto RIP SummaryPoison Reverse Authentication requiredRIP Version NAT/DMZ Count Global Start IP Address Multi-DMZMulti-NAT Virtual Start IP AddressVirtual Server Basic Firewall Security FirewallAutomatic Firewall Security Connections and will be unresponsive Advanced Firewall SecurityClick Advanced Firewall Security and then press Finish SYN AttackPing of death attack attempts to crash your system by Addresses originating from your networkDest. IP Address DirectionDescription Src. IP AddressFiltering rule will be configured as follow Filtering Rule for Smtp connectionFiltering Result Update Filtering Rule10.0.0.0 172.16.6.0 Permit 10.1.99.0 172.16.0.0 Deny Any When the rule is ordered as ABCRule Order IP QoS NB714 User Guide Administration Security NB712 / NB714 User Guide MIB SnmpCommunity Snmp statusVersion Community Click on Time Sync Time SyncTime Zone Sntp serviceTime Server Utility System Info Lose all the configured parameters Restore ConfigurationBackup Configuration 10.2 Config ToolUpgrade To logout the router, press logout LogoutRestart You can monitor the following StatusLAN Parameters LAN-to-LAN connection with bridge ModeCO side Enter VPI Enter VCI Encap WAN1 ParametersEnter IP 192.168.1.1 Enter Subnet Mask Enter Gateway 192.168.1.1 Enter Host NameVCI32 EncapLLC CPE SideHost Name Enter Soho IP Address 192.168.20.1 Subnet Mask 255.255.255.0 Host Name LAN to LAN Connection with Routing ModeDhcp Service Click Route and CO Side then press NextWAN Parameters Click Next to setup the IP parametersIP Address 192.168.10.1 Subnet Mask 255.255.255.0 Host Name Click Route and CPE Side then press Next192.168.30.2 Baudrate 9600 Data Bits Parity Check Stop Bits Flow-control Useradmin PasswordSerial Console TelnetOperation Interface Window structure Ctrl + C To quit the configuring item Ctrl + Q For help Menu Driven Interface CommandsTo choose another parameters Menu Tree 14.7 Configuration Exit Quit system Ping Packet internet groper command AdminDone via utility command UtilityStatus Script ShowSystem ConfigPing RebootAdministration WriteUser Profile Edit Community Entry List Show Snmp Supervisor Password and ID Move the cursor to timeserver1 and press enter Move the cursor to service and press enterSntp Move the cursor to sntp and press enterMove the cursor to list and review the setting Mode SetupUtility ExitShdsl 14.16.3 WAN After enter add menu, the screen will prompt as follow BridgeMove the cursor to vlan and press enter VlanFor each VLAN, Vlan ID is a unique number among 1~4095 14.16.6 802.11Q VlanFollow the following steps to configure 802.11q Vlan Screen will display the following Generic command can setup RIP mode and auto summery modeYou can review the list of RIP parameters via list command RouteIP share 14.16.8 LANYou can configure NAT parameters in nat menu 14.16.10 NATMapping After key in enter, the screen will prompt as below 14.16.11 PATFirewall You can enable the demilitarized zone via active commandfirewall security level can configure via level command 14.16.12 DMZActive DoS Protection IPQoS Dhcp You can view the Dhcp configuration via list commandHost name DefaultDNS proxy 100Mbps Appendix a Cable InformationRJ-45 Network Ports 10MbpsCross-Over Cabling Straight and crossover cable configurationStraight-Through Cabling TxD Shdsl Line Connector Console CableNo connection RxD OContact Information Appendix B Registration and Warranty InformationProduct Warranty
Top Page Image Contents