MRV Communications LX-4000 Series manual LX-4000 Indicators and Interfaces, Front Panel LEDs

Page 16

Installing the LX-4000 Series

LX-4000 Indicators and Interfaces

This section explains the LX-4000 unit’s indicators and interfaces.

Front Panel LEDs

This section explains the front panel LEDs (see Figures 1 through 4).

Figure 1 - LX Series 4008 Front Panel

Figure 2 - LX Series 4016 Front Panel

FLT OK

Figure 3 - LX Series 4032 Front Panel

Modem Port

FLT OK 100 Mbps LED

DIAG Port (Port 0)

Figure 4 - LX Series 4048 Front Panel

FLT

Solid red indicates a fault condition exists or maintenance is required. This LED remains on until the initial Power On Self Test (POST) completes successfully.

OK

Solid green indicates the system’s voltages are normal and the unit has passed the POST test.

16

MRV Communications, Inc.

www.mrv.com

451-0308

Image 16

Contents MRV Americas Service and Support Getting Started with the LX-4000 SeriesCorporate Headquarters MRV America Sales MRV International SalesFCC Notice Bsmi Notice Vcci Notice Licensing Notice451-0308 Table of Contents Appendix C Post Test Error Codes Figures 451-0308 Tables 451-0308 Preface Customer SupportOther Documentation Chapter Overview of the LX-4000 Series ConventionsSystem Specifications DescriptionChapter Installing the LX-4000 Series Hardware InstallationPackage Contents Unpack and Inspect the UnitLX-4000 Indicators and Interfaces Front Panel LEDsRear Panel LEDs Port Status LEDsRCV Link Environmental and Installation Considerations MbpsConnect the Power Cable Connecting the Ethernet InterfaceMounting the Unit into a 19-inch or 23-inch Rack Cable ConnectionsConnecting DC Power Connecting Your Management StationConnect Serial Device Cables Powering On Modem Port OptionalSystem Login and Passwords Resetting the UnitInstalling the LX-4000 Series Configuring the LX-4000 Unit for the First Time Chapter Configuring the LX-4000 Series for the First TimeFirst Time Quick Configuration 451-0308 Completing the First Time Configuration Assigning an IP Address via the NetworkManually Setting the IP Address Via the CLI Accessing and Configuring the Graphical User Interface GUIMRV Communications, Inc 451-0308 Web Configure Mode Web Access Mode Menu/Config ModeGUI EZ Configuration Launching the EZConfig GUISoftware Upgrades IP Configuration MenuBooting from Defaults Accessing and Configuring Additional FeaturesAdditional Considerations Command Line Interface CLI Tree Structure Autobauding FeatureReinitializing/Powering Off the Unit Additional Considerations for an Internet EnvironmentConnecting the Temperature/Humidity Sensor Sensor Temperature/Humidity PortsChapter Alternative Port Capabilities Power Management Async 4-40access sensorConnecting ConnectingPower Strip Management Telco Using LX Ports as Alarm Inputs and Control Outputs Alarm Inputs Setup and UsageControl Output Setup and Usage Typical Alarm Inputs ConnectionsTypical Interface Design for Control Output Signals Appendix a Technical Specifications LX-4000 Series Specifications DescriptionLX-4008, LX-4016 Appendix a Technical Specifications Temperature/Humidity Sensor Specifications Description Appendix B Factory Defaults LX-4000 Series Factory Defaults DescriptionPpciboot Factory Default Settings Main Menu Configuration Factory Default SettingAppendix C Post Test Error Codes Error Code Definitions451-0308 Post Test Error Code Sample 3 4 5 6 7 Serial Device Connectors Diagnostic Port Connector PortAppendix D Cabling the LX-4000 Series Cabling Considerations10/100 Connector Modular AdaptersOrdering Cables Pin AssignmentsDB-25 Pins Connecting to the Diagnostic Port Port Ordering and Installing the Inlet Connector LockModem Control/Hardware Flow Control RJ-45 Wiring Considerations Modular Adapters RJ-45 to DB-25Supports RTS/CTS MRV 8-Wire Cabling Adapter Wiring, LX-Series to DCE, with RingMX-151-3027 LX SeriesNumerics DB-2556, 61 RJ-4561 RJ-45 jacks Index