MRV Communications LX-4000 Series manual Power Strip Management

Page 40

Alternative Port Capabilities

5150 Power Strip Management

The 5150 Series family of products provides easy, practical, and secure solutions for power distribution, power management and load-measurement for remote internetworking equipment and branch AC circuits.

5150 Series products are available in 8-outlet and 16-outlet configurations for 100-120VAC up to 30A, and for 230VAC up to 16A (Continental Europe). An 5150 Series offers individual remote control over the power on/off status to a maximum of 16 devices.

The following section explains how to connect and install the 5150.

Connecting the 5150

The 5150 Series is equipped with a single RJ45 RS-232 serial port for attachment to a PC or networked terminal server using the supplied RJ45 to RJ45 crossover cable and RJ45 to DB9F serial port adapter as required. See the Technical Specifications in Getting Started with the MRV Communications 5150 Power Control Series for more information on the RS-232 serial port.

To connect the 5150:

1.Connect one end of the standard RJ-45 double-ended crossover cable to the serial port of the 5150.

2.Connect the other end to any port you have configured as a power management port.

Serial Port

IR-5150

RJ-45 Double-Ended

Crossover Cable

LX-4000

TELCO

100-240VACLINE

1.0A 50/60Hz

1	2	3	4	6	7	8	9	10	11	12	13	14	15	16	RCV			LINK

100

DIAG 10/100 ETHNT

Figure 18 - Connecting the 5150

You must change the port’s “access” to “power model ir5150” before performing any control and monitoring. Use the following command, in the Async Port Configure Mode, to configure asynchronous port 1 as an 5150 port:

Async 1-1:0>>access power model ir5150

Once the 5150 is enabled, you can check its status with the following command:

InReach:0>> show port async 1 status

40

MRV Communications, Inc.

www.mrv.com

451-0308

Image 40

Contents MRV Americas Service and Support Getting Started with the LX-4000 SeriesCorporate Headquarters MRV America Sales MRV International SalesFCC Notice Bsmi Notice Vcci Notice Licensing Notice451-0308 Table of Contents Appendix C Post Test Error Codes Figures 451-0308 Tables 451-0308 Preface Customer SupportOther Documentation Chapter Overview of the LX-4000 Series ConventionsSystem Specifications DescriptionChapter Installing the LX-4000 Series Hardware InstallationPackage Contents Unpack and Inspect the UnitLX-4000 Indicators and Interfaces Front Panel LEDsRear Panel LEDs Port Status LEDsRCV Link Environmental and Installation Considerations MbpsConnect the Power Cable Connecting the Ethernet InterfaceMounting the Unit into a 19-inch or 23-inch Rack Cable ConnectionsConnecting DC Power Connecting Your Management StationConnect Serial Device Cables Powering On Modem Port OptionalSystem Login and Passwords Resetting the UnitInstalling the LX-4000 Series Configuring the LX-4000 Unit for the First Time Chapter Configuring the LX-4000 Series for the First TimeFirst Time Quick Configuration 451-0308 Completing the First Time Configuration Assigning an IP Address via the NetworkManually Setting the IP Address Via the CLI Accessing and Configuring the Graphical User Interface GUIMRV Communications, Inc 451-0308 Web Configure Mode Web Access Mode Menu/Config ModeGUI EZ Configuration Launching the EZConfig GUISoftware Upgrades IP Configuration MenuBooting from Defaults Accessing and Configuring Additional FeaturesAdditional Considerations Command Line Interface CLI Tree Structure Autobauding FeatureReinitializing/Powering Off the Unit Additional Considerations for an Internet EnvironmentConnecting the Temperature/Humidity Sensor Sensor Temperature/Humidity PortsChapter Alternative Port Capabilities Power Management Async 4-40access sensorConnecting ConnectingPower Strip Management Telco Using LX Ports as Alarm Inputs and Control Outputs Alarm Inputs Setup and UsageControl Output Setup and Usage Typical Alarm Inputs ConnectionsTypical Interface Design for Control Output Signals Appendix a Technical Specifications LX-4000 Series Specifications DescriptionLX-4008, LX-4016 Appendix a Technical Specifications Temperature/Humidity Sensor Specifications Description Appendix B Factory Defaults LX-4000 Series Factory Defaults DescriptionPpciboot Factory Default Settings Main Menu Configuration Factory Default SettingAppendix C Post Test Error Codes Error Code Definitions451-0308 Post Test Error Code Sample 3 4 5 6 7 Serial Device Connectors Diagnostic Port Connector PortAppendix D Cabling the LX-4000 Series Cabling Considerations10/100 Connector Modular AdaptersOrdering Cables Pin AssignmentsDB-25 Pins Connecting to the Diagnostic Port Port Ordering and Installing the Inlet Connector LockModem Control/Hardware Flow Control RJ-45 Wiring Considerations Modular Adapters RJ-45 to DB-25Supports RTS/CTS MRV 8-Wire Cabling Adapter Wiring, LX-Series to DCE, with RingMX-151-3027 LX SeriesNumerics DB-2556, 61 RJ-4561 RJ-45 jacks Index