Milan Technology MIL-SM4804G manual Vii

Page 11

Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft werden:

Schweiz	Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen einhalt-
	en.

Europe	Das Netzkabel muß vom Typ HO3VVF3GO.75 (Mindestanforderung)
	sein und die Aufschrift <HAR> oder <BASEC> tragen.
	Der Netzstecker muß die Norm CEE 7/7 erfüllen (”SCHUKO”).

Warnings and Cautionary Messages

Warning: This product does not contain any serviceable user parts.

Warning: Installation and removal of the unit must be carried out by qualified personnel only.

Warning: When connecting this device to a power outlet, connect the field ground lead on the tri-pole power plug to a valid earth ground line to prevent electrical hazards.

Warning: This switch uses lasers to transmit signals over fiber optic cable. The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation. However, you should never look directly at a transmit port when it is powered on.

Caution: Wear an anti-static wrist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment.

Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Les raccordeurs ne sont pas utilisé pour le système téléphonique!

Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC standards.

Warnings (in German)

Achtung: Dieses Produkt enthält keine Teile, die eine Wartung vom Benutzer benötigen.

Achtung: Installation und Deinstallation des Gerätes müssen von qualifiziertem Servicepersonal durchgeführt werden.

Achtung: Wenn das Gerät an eine Steckdose angeschlossen wird, muß der Masseanschluß am dreipoligen Netzstecker mit Schutzerde verbunden werden, um elektrische Gefahren zu vermeiden.

Achtung: Dieses Gerät nutzt Laser zur Signalübertragung über Glasfasern. Die Laser entsprechen den Anforderungen an eine Lasereinrichtung der Klasse 1 und sind durch ihre Bauart im normalen Betrieb sicher für die Augen. Trotzdem sollte niemals direkt in den einen Übertragungskanal geblickt werden, wenn er eingeschaltet ist.

vii

Image 11

Contents MIL-SM4804G Page Quick Installation Guide MIL-SM4804G 90000444 REV a European Notice Regulatory ApprovalCanadian EMI Notice You can reach MiLAN Technology technical support at TrademarksTo Contact MiLAN Technology Iii Compliances and Safety WarningsWarnhinweis Faseroptikanschlüsse Optische Sicherheit Safety CompliancePower Cord Set France et Pérou uniquement Vii Viii End of Product Life SpanManufacturing Materials DocumentationContents Appendix B Cables B-1 Appendix a Troubleshooting A-1Appendix C Specifications C-1 Making Network ConnectionsTables Figures Overview Introduction10BASE-T/100BASE-TX Ports Switch ArchitectureDescription of Hardware Network Management Options1000BASE-T/SFP Ports Stacking Ports Stacking PortsLED Port and System Status LEDsSystem LEDs Expandability Features and BenefitsPower Supply Receptacles ConnectivityManagement PerformanceNetwork Planning Introduction to SwitchingNetwork Planning Application ExamplesCollapsed Backbone Network Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Ethernet Cabling Installing the SwitchSelecting a Site Optional Rack-Mounting Equipment Equipment ChecklistPackage Contents Mounting MountingRack Mounting Rack-Montage Montage Rack Mounting Instructions GermanAttaching the Adhesive Feet Desktop or Shelf MountingConnecting Switches in a Stack Installing an Optional SFP TransceiverConnecting Switches in a Ring-topology Stack MIL-SM4804G Connecting to a Power SourceWiring Map for Serial Cable Connecting to the Console PortInstalling the Switch Cabling Guidelines Connecting Network DevicesMaking Network Connections Twisted-Pair DevicesMaking Network Connections Connecting to PCs, Servers, Hubs and SwitchesNetwork Wiring Connections Network Wiring Connections Fiber Optic SFP Devices 1000BASE-T Cable Requirements Connectivity RulesMbps Ethernet Collision Domain Mbps Gigabit Ethernet Collision DomainMbps Fast Ethernet Collision Domain Cable Labeling and Connection Records Making Network Connections Diagnosing Power Problems with the LEDs Appendix a TroubleshootingDiagnosing Switch Indicators Stack Troubleshooting Power and Cooling ProblemsInstallation In-Band Access10BASE-T/100BASE-TX Pin Assignments Appendix B CablesTwisted-Pair Cable and Pin Assignments Cables Straight-Through WiringCrossover Wiring Twisted-Pair Cable and Pin Assignments B 1000BASE-T Pin AssignmentsFiber Standards Cable Testing for Existing Category 5 CableAdjusting Existing Category 5 Cabling to Run 1000BASE-T Physical Characteristics Appendix C SpecificationsSpecifications Switch FeaturesManagement Features Standards C StandardsCompliances Specifications Bandwidth Glossary1000BASE-T Auto-NegotiationEthernet CollisionCollision Domain End StationIeee 802.3z Media Access Control MACRedundant Power Supply RPS Ieee 802.3uVirtual LAN Vlan RJ-45 ConnectorSwitched Ports Transmission Control Protocol/Internet Protocol TCP/IPIndex-1 IndexNumerics Index-2 IndexIndex-3 Index Index-4 Page MIL-SM4804G 90000444 REV a