MaxTech xpvs336i Appendix B - FCC , DOC & Other Notices, FCC Compliance, FCC Class B Statement

Page 20
Appendix B - FCC , DOC & Other Notices

Power:

0.75 W

Temperature:

0 to 55 degrees C (Operating)

Caller ID:

Yes

PnP:

Revision 1.0a

Speakerphone:

Full-duplex with DSP echo

 

cancellation

 

 

Appendix B - FCC , DOC & Other Notices

FCC Compliance

This equipment complies with Part 68 of the FCC Rules. On this equipment is a label that contains, among other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company.

If your telephone equipment causes harm to the telephone network, the Telephone Company may discontinue your ser- vice temporarily. If possible, they will notify in advance. But, if advance notice is not practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with the FCC.

Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect proper operation of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service.

The FCC prohibits this equipment to be connected to party lines or coin-telephone service.

In the event that this equipment should fail to operate properly, disconnect the equipment from the phone line to determine if it is causing the problem. If the problem is with the equipment, discontinue use and contact your dealer or vendor.

The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part 68, Sec. 68.381 (c) (3)).

FCC Class B Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful interference in a residential installation. This equipment generates, uses and can radiate radio fre- quency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio com- munications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

18

Image 20
Contents High Performance V.34+/V.42bis 33,600 BPS Internal Plug and Play FAX/Voice/Data ModemFeaturing Advanced Full Duplex Speakerphone Functions MAN081 RevContents Section Two - Installation Section One - Introduction2.1 Unpacking Your Modem 2.2 What You Need You will needBack Plate 2.3 Hardware InstallationExpansion Slots Section 2.4.3 if you are running Windows 3.1x on a non-PnP PC 2.4.2 Configuring in a Plug and Play System without Windows 2.4.3 Configuring in a Non-Plug and Play System2.5 Software Installation and Configuration 2.9 Where To Go From Here 2.7 Testing Your Modem After Installation2.8 Using Your Modem Section Three - AT Command Set @ wait for five seconds of silence flash Reportlinespeed,errorcorrectionprotocol ModemsendsbreaksignalforfoursecondsForce Carrier Detect Signal High ON Modem returns to Command Mode afterConfiguration Profile 0 active upon Grant Remote Digital Loopback TestenabledwithV.8/V.32AnnexA.Parameter Enable MNP Class 5 and V.42bis data300, 33600. Parameter “a” specifies the Returns Caller ID capabilities of modemV.42/MNP/Normal data link V.42 data link onlyMNP data link only Enable Caller ID detection and reporting Section Four - S RegistersRange/units Default Table 4-1 S - RegistersRegister FunctionSection Five - Result Codes Section Six - TroubleshootingModem does not respond to commands Modem experiences errors while communicating with a remote modem Modem does not dialModem dials but does not connect Modem makes a connection but no data appears on your screenModem exhibits poor voice record or playback Section Seven - Support and ServiceAppendix A - Specifications FCC Class B Statement Appendix B - FCC , DOC & Other NoticesFCC Compliance DOC Compliance Information UL Notice