Lucent Technologies 7820-0766-004 manual Main menu Second-level menus/description

Page 20

Command-Line Interface

Bridging commands

save	- save and restart			modem
show	-	display	configuration of PVC and Ethernet
ver	-	display	software	version

Note: *The WAN interface displayed in the menu is dependent on the interface supported by your unit. This generic form of presentation has been arrived at to eliminate the need of representing every interface.

Table 3-1 lists the main menu commands and their corresponding second-level menus. The different WAN interfaces and their corresponding menus are presented in sequence. Select the interface and menus appropriate to your unit.

Table 3-1. Main menu and second-level bridging commands

Main menu	Second-level menus/description

adsl	abort	- abort ADSL line
	bitdn	- ADSL downstream bit loading value
	bitup	- ADSL upstream bit loading value
	coding	- <0><1><2><3><4><5><6><Auto> dB -
		coding gain
	counts	- display ADSL counters
	default	- reset to default ADSL setting
	ec_fdm	- <Ec><Fdm> - set EC or FDM mode
	rx_bin	- <start_bin> <end_bin>
	show	- display ADSL parameter configuration
	startup	- restart ADSL line
	status	- display ADSL line status
	stnl	- <T1.413><g.Lite><g.Dmt><Multi Mode>
	trellis	- <Enable><Disable> - Trellis encoding
	tx_pwr	- <0> .. <12> dB - Tx power attenuation
	tx_bin	- <start_bin> <end_bin>

3-4	CellPipe™ 20 Series User’s Guide

Image 20

Contents CellPipe 20 Series Lucent Technologies Customer Service Customer ServiceFinding information and software Obtaining technical assistanceCustomer Service Contents Upgrading System Software Introduction About this guideWhat is the CellPipe 20 Series Product Family? What is the CellPipe 20 Series Product Family?Lucent TURN-UP Lucent TURN-UPCellPipe 20 Series management Page Setup Verifying package contentsItems you need for installation Items you need for installationConnecting CellPipe 20 Series products Connecting CellPipe 20 Series products CellPipe 20 Series rear panelsChecking status lights Console setupChecking status lights Console setup Page Command-Line Interface Syntax of command-line interfaceUsing the commands Displaying information about a commandUsing the commands Viewing the main menuBridging commands Displaying second-level commandsSaving configurations Bridging commandsMain menu Second-level menus/description Set all configuration to factory setting Routing commands Routing commandsAdditional main-menu and second-level routing commands Command-Line Interface Command-Line Interface Page Configuring a 20 Series CellPipe Auto-provisioningConfiguring WAN interface Configuring WAN interfaceSdsl commands and configurations Select the dbit command to configure the sdsl data bit Adsl commands and configurations Select the abort command to abort the Adsl connection Multimode Configuring LAN interface Configuring LAN interfaceConfiguring LAN interface in bridging mode Configuring LAN interface in routing mode Configuring the manage command Configuring the manage commandConfiguring the mode command Configuring the quick command Quick command in bridging modeQuick command in routing mode Configuring the quick commandConfiguring the r1483 command Configuring the r1483 commandR1483 command in bridging mode R1483 command in routing mode Configuring the dnsrelay command Configuring the dnsrelay commandConfiguring the ipoa command Configuring the pppoa command Configuring the pppoa commandConfiguring the pat command Configuring the pat commandSelect the show command to display the Pat configuration Obtaining software Preparing to upgradeUpgrading System Software Upgrading software Upgrading softwareProduct warranty Warranties and FCC RegulationsWarranty repair Out-of warranty repairFCC Part 15 Notice FCC Part 15 NoticeIC CS-03 Notice IC CS-03 Notice