POWER SOURCES
Notes on 
•During playback (batteries are in use), 
is on.
•When the battery voltage level is low, 
will flash. 10~15 minutes, playback still continues in this period.
•Playback will automatically come to a stop when the batteries have no
more power. Do not repeat pressing 
as the unit may operate incorrectly. Replace all the batteries with new ones.
•
will not be on if an AC adaptor is used.
Using on house current
If the unit you purchased does not include an AC power adaptor, please use a 6V 450mA AC power adaptor. Otherwise use only the supplied AC power adaptor.
Be sure to disconnect the AC power adaptor when the unit is not in use.
LISTENING TO THE RADIO
1.Set the FUNCTION switch to select "RADIO".
2.Press BAND button to select the desired band AM (MW) or FM.
3.Press TUNING buttons to turn the station.
To tune faster
Hold down the TUNING button. While the button is being held, the frequency will change faster.
To search for a station quickly (AUTO Search)
Keep the TUNING's or 
button pressed until the tuner starts searching for a station. After tuning in to a station, the search stops.
To stop the Auto Search manually, press the TUNING's or 
button. * The Auto Search may not stop at stations with very weak signals.
To turn off the RADIO
Press OFF button or set the FUNCTION switch to "CD".
Presetting RADIO station
You can tune into a stored station directly by entering the preset number.
•10 stations on FM band can be preset.
•10 stations on AM (MW) band can be preset.
1.Set the FUNCTION switch to select "RADIO".
2.Press BAND button to select the desired band AM (MW) or FM.
3.Press TUNING buttons to tune your required station.
4.Press MEM (Memory) button.
The "PGM" indicator will flash in the display window.
5.Select a preset number (M1 ~M5+) button, or press the PRESET button to select preset number.
6.Press MEM (Memory) button to store the station.
7.Repeat steps 2 to 6.
To select a numbered button from M6 to M10.
First press the M5+ button, then press one of numeric buttons.
Tuning into a preset station
Press the preset number (M1~M5+) button.
Or press the PRESET button to select preset number.
For better reception
To improve FM reception: | To improve AM (MW) reception: |
extend the headphone cord. | rotate the unit. |
NOTE:
*The FM "STEREO" indicator lights up when the tuned-in station is broadcasting in stereo and the reception is good.
DISC PLAYING
1.Set the FUNCTION switch to select " CD".
2.Open the CD door with the OPEN button.
3.Insert the CD with the printed side facing upwards and push the disc gently until it clicks so that the disc fits into the pivot.
4.Press the CD door to close.
Note: To play an 8 cm (3-inch) disc, you can play it without an adaptor.
On display window
When you press 
, the display window shows:-
First track playing begins
During play
The track number of the current selection appears.
When " 
/OFF" is pressed during play, total number of tracks on the disc will be displayed and the unit is still on. If " 
/OFF" is pressed again the unit will be returned to full stop mode. If " 
" is pressed the unit returns to play mode. The unit will be returned to full stop mode automatically after approximately 30 seconds if no button is pressed.
During pause
The playing track number flashes.
Pause mode of the second track
When no disc is inserted onto the player and when " 
" is pressed, the
display window shows " 
"
The unit cannot be operated when no disc message is displayed. After approx. 30 seconds the unit will return to full stop mode, or reset the player by pressing " 
/OFF" once and then insert a disc to start playing.
VARIOUS PLAYING MODES
During playback, every time the P. MODE (PLAY MODE) key is pressed, the mode will change to the next one as follows:
NORMAL play -> INTRO -> PGM (PROGRAM) -> SHUFFLE
Normal Play - Playing the Whole Disc
The CD is played once from beginning to end.
INTRO Play - Playing the First Ten Seconds of All the Selections
1. Press P. MODE (Play mode) during play until
" 
" flashes in the display window.
2. Press 
to begin the INTRO play.
3. Pressing P.MODE again will cease the INTRO play and continue playback in the NORMAL play mode.
*INTRO play always starts from the first track.
PGM (Program) Play - Playing the Selections in the Desired Order
1. Press P. MODE (Play mode) button until
“PGM” flash and " 
" in the display window.
2. Press 
or 
to select the desired selection.
3. Press MEM/REPEAT/ENTER button to store this track in memory.
4. To add additional tracks, repeat steps 2 and
3.
5. Press 
, "PGM" stops flashing and play starts.
To Edit Program Play:
To check: | Press "MEM/REPEAT/ENTER" lightly during programming |
| before you press . Each time "MEM/REPEAT/ENTER" |
| is pressed the track number appears in the display |
| window. | | |
To change: | When checking press either | or | to alter the track |
| number for the program currently displayed. Press "MEM/ |
| REPEAT/ENTER" to register the newly selected track into |
| memory. | | |
To delete: | When open the CD door including that program will be |
| cancelled. | | |
SHUFF (Shuffle) Play - Playing the Selections in Random Order
1. Press P. MODE (Play Mode) during play until "SHUFF" flashes in the display window.
2. Press 
to begin the SHUFFLE play.
* To locate the beginning of the track being
played: press 
.
* To locate the next track: press 
. However, you cannot locate a previous track even if
you keep 
pressed.
Repeat Playback (Repeat One and Repeat All)
•To repeat the same track
Press MEM/REPEAT/ENTER during play until
" 
1" appears in the display window. Select desired track to be played only once
by pressing 
or 
.
• To repeat the whole disc
Press MEM/REPEAT/ENTER during play until
"
ALL" appears in the display window.
Note:
* Repeat play can be performed during program, intro and shuffle play.
*The program is also erased when the disc compartment is opened or the auto power off function turns the power off.
*If the program mode is exited by means of the “ 
/OFF” key, all the programs would still remain in memory.
*During the program play, the AMS operates in the programed order. (AMS-auto music sensor)
DIGITAL ANTI-SHOCK SYSTEM
The Digital Anti-Shock System incorporates a special electronic circuit that prevents sound from skipping when the unit is subjected to shocks and vibration during play.
When you start playback, the Anti-Shock System turn on and "
" indicator appears in the display to prevent sound skipping.
When the unit receives a physical shock which prevents the laser pick-up from "reading" the CD, this system immediately starts playing the sound stored in its memory and continues until the laser pick-up recovers.
If the unit is subjected to continuous shocks and all the data stored in memory is used up the sound will skip.
If the vibration stops then the data memory will be restored. If continuous vibration is applied when the data memory is empty, an error message "
" will be displayed. To reset the CD player press " 
/OFF" once.
To cancel the Anti-Shock System, press the ANTI-SHOCK button, then "
" indicator disappears in the display
NOTES:
•In the "DIGITAL ANTI-SHOCK SYSTEM", battery power consumption is more because the disc rotates faster than normal and the memory circuit is active.
•When the Digital Anti-Shock System is switched on or off, the sound will be interrupted for a short time. This is normal.
•Under some conditions, noise may be heard or sound skipping may occur.
-when the disc is dirty or scratched.
-when the disc contains certain signals.
-when the unit is subjected to a certain kind of shock.
In these conditions, try to release "DIGITAL ANTI-SHOCK SYSTEM."
TROUBLESHOOTING GUIDE
Should any problem persist after you have made the following checks, consult your nearest service facility.
Disc play does not start:
•The disc is inserted upside down or incorrectly. Insert the disc correctly with the label surface up • Dusty or defective disc • Dirty or dusty lens. • The disc compartment lid is not closed • Moisture condensation -> Leave the unit in a warm place until the moisture evaporates • The AC power adaptor is not plugged into the wall outlet
•The unit is not placed on a level surface • Weak batteries
No sound from the headsets:
•The headphones/earphone plug is not firmly connected to the PHONES jack • Adjust the VOL control • Dirty plug
No sound from the connected speakers:
•Check the connections • The amplifier is not turned on
Skipping of sound:
•Dirty or defective disc • Dirty lens. • Strong vibration
When using with batteries the battery life is short:
•Manganese batteries are used. Use alkaline batteries
Display window shows " 
" error message and the unit cannot be operated:
•No disc , dirty disc or scratched disc. The unit will return to full stop mode after approx. 30 seconds, or reset the player by pressing "STOP" once and then insert a disc to start playing.
MAINTENANCE
Cleaning the unit
Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft cloth.
Cleaning CD
If the CD skips or will not play, the disc may need to be cleaned. Before playing, wipe the disc in a circular motion from the centre out with a cleaning cloth. After playing, store the disc in its case.
Handling the disc
Only touch the CD on the edge to avoid finger prints on its surface. Do not stick paper or tape nor write anything on the surface.
SPECIFICATIONS
General
Compact disc digital audio system
•Digital filter two-time oversampling
•Three-spot optical pick up
| | | | | | |
Output (at 1KHz 0dB level) | Line output (stereo minijack) |
| Output level 0.4V (Rms) at 47KΩ at 1KHz |
| Headphones/earphone (stereo minijack) |
| 15 mW + 15 mW at 16Ω to 32Ω |
Power requirements | 2 size AA (LR6 or UM-3) alkaline batteries, |
| or | | | |
| DC IN 6V, 450mA power adaptor |
| Polarity of plug | |
| | | | |
Operating voltage: | U.S.A., Canada: | |
(AC adaptor) | 120V AC | 5% 60 Hz |
| Middle East and Australia: |
| 240V AC | 5% 50 Hz |
| UK and Germany: |
| 230V AC | 5% 50 Hz |
| Chile: 230V AC | 5% 50 Hz |
| Singapore, Malaysia & Thailand: |
| 200-240V AC | 5% 50 Hz |
| Japan: 100V AC | 5% 50/60Hz |
Frequency range: | FM | 87.3 - 108.1 MHz |
| AM | 520 - 1720 KHz |
Dimensions: | Approx. 132 x 147 x 38 mm (w/h/d) |
Weight: | Approx. 290g (not incl. batteries) |
Design and specifications are subject to change without notice.
Printed in CHINA | 811-990591-010 |
