LevelOne WAP-0005 user manual Setup using a Web Browser, Password Dialog

Page 13

Wireless Access Point User Guide

Setup using a Web Browser

Your Browser must support JavaScript. The configuration program has been tested on the following browsers:

Netscape V4.08 or later

Internet Explorer V4 or later

Setup Procedure

Before commencing, install the Wireless Access Point in your LAN, as described previously.

1.Check the Wireless Access Point to determine its Default Name. This is shown on a label on the base or rear, and is in the following format:

SCxxxxxx

Where xxxxxx is a set of 6 Hex characters ( 0 ~ 9, and A ~ F ).

2.Use a PC which is already connected to your LAN, either by a wired connection or an- other Access Point.

Until the Wireless Access Point is configured, establishing a Wireless connection to it may be not possible.

If your LAN contains a Router or Routers, ensure the PC used for configuration is on the same LAN segment as the Wireless Access Point.

3.Start your Web browser.

4.In the Address box, enter "HTTP://" and the Default Name of the Wireless Access Point e.g.

HTTP://SC2D631A

5.You should then see a login prompt, which will ask for a User Name and Password. Enter admin for the User Name, and password for the Password.

These are the default values. The password can and should be changed. Always enter the current user name and password, as set on the Admin Login screen.

Figure 7: Password Dialog

6.You will then see the Status screen, which displays the current settings and status. No data input is possible on this screen.

10

Image 13
Contents LevelOne Table of Contents Overview General Problems Wireless Access PointOverview Wireless LAN Terminology Overview Command ReferenceIntroduction Features of your Wireless Access PointAdvanced Features Security FeaturesPhysical Details Package ContentsPower port To Clear All Data and restore the factory default valuesRear Panel EthernetProcedure InstallationRequirements RequirementsUsing PoE Power over Ethernet Using PoE Power over EthernetSetup using the Windows Utility Access Point SetupInstallation OverviewButtons Wireless Access PointsWireless Security Wireless Security Setup ProcedurePassword Dialog Setup using a Web BrowserIf you cant connect System Access Control WirelessManagement Status Screen Data System Screen System ScreenIdentification IP AddressData Access Control Screen Access ControlTelnet Data Trusted Wireless Stations Trusted Wireless StationsButtons Select None Select AllEdit AddBasic Settings Screen Wireless ScreensData Basic Settings Screen Wireless ModeChannel No Remote APCurrent Channel Broadcast Ssid Security Settings Radius MAC Authentication Security Settings NoneUsing MAC authentication Data Radius-based MAC Authentication Screen Radius-based MAC authentication ScreenUAM authentication External UAM authentication InternalUAM Screen AuthenticationData UAM Screen InternalData WEP Screen Security Settings WEPKey Value Key InputPassphrase Radius MACData WPA-PSK Screen Security Settings WPA-PSKNetwork Key WPA EncryptionGroup Key Update Pairwise Key UpdateUpdate Group key when any membership terminates Key LifetimeData WPA-802.1x Screen Security Settings WPA-802.1xWPA-802.1x Update Group key UpdateWhen any member Update ReportData 802.1x Screen Security Settings802.1x Radius Server AddressWEP Key Size Update Report everyKey Exchange Data Advanced Settings Screen Advanced SettingsBasic Rate Options802.11b 2.4GHz only ParametersUsing WEP PC and Server ConfigurationMode SecurityUsing WPA-PSK Wireless Station Configuration Using WPA-802.1xRadius Server Configuration 802.1xWindows 2000 Domain Controller Setup 802.1x Server Setup Windows 2000 ServerServices Installation Components Screen CA Screen Dhcp server configurationIP Address Screen Certificate Authority Screen Certificate Authority SetupActive Directory Screen Group Policy Screen Service Screen Internet Authentication Service Radius SetupAuthentication Screen Dial-in Screen Remote Access Login for UsersClient Certificate Setup 802.1x Client Setup on Windows XPWireless CA Screen Identifying Information Screen Encryption Settings 802.1x Authentication SetupEnabling Encryption Wireless Networks ScreenProperties Screen Using 802.1x Mode without WPA Operation Operation and StatusStatus Screen Wireless Access PointData Status Screen SecurityData Activity Log Activity LogData Data Station List Screen Station ListStation List Statistics Screen 4GHz WirelessData Statistics Screen System Up TimeControl Admin Login Screen Other Settings & FeaturesData Admin Login Screen Password Dialog Data Config File Screen Config FileBackup RestoreGeneral Data Snmp ScreenManagers TrapsTo perform the Firmware Upgrade Firmware UpgradeWireless Access Point SpecificationsHardware Specifications Wireless SpecificationsFeature Details Software SpecificationsMessage Log FCC Radiation Exposure Statement FCC StatementGeneral Problems TroubleshootingTo Find the Access Points IP Address Appendix B Troubleshooting Windows TCP/IP Checking TCP/IP Settings Windows 9x/MENormally, no changes need to be made Using Specify an IP Address Using DhcpWindows NT4.0 TCP/IP Checking TCP/IP Settings Windows NT4.0Obtain an IP address from a Dhcp Server Network Configuration Win Checking TCP/IP Settings WindowsUsing a fixed IP Address Use the following IP Address Network Configuration Windows XP Checking TCP/IP Settings Windows XPUsing Dhcp Wireless LAN Terminology About Wireless LANsAd-hoc Mode Infrastructure ModeWPA-802.1x Channels802.1x Using the CLI Telnet Command Line InterfaceUsing the CLI Serial Port CLI Port Settings Command ReferenceAppendix E Command Line Interface Wireless Access Point User Guide Appendix E Command Line Interface Wireless Access Point User Guide Set Extended Channel Mode Wireless Access Point User Guide Set wep -- Set Encryption Mode
Related manuals
Manual 108 pages 28.18 Kb