Lancom Systems 3550 manual Activate UMTS/GPRS profile

Page 47

LANCOM 3550 Wireless

Chapter 5: Setting up the UMTS profile

The UMTS/GPRS profile settings are to be found in LANconfig in the configu- ration area 'Interface' on the 'WAN' tab with the UMTS/GPRS profile button.

EN

ple, by using Telnet under /Status/External-Interface/Net- work-List. A manual network search can be initiated with the commands do /Status/External-Interface/Scan-Networks

or so Setup/Interfaces/UMTS-GPRS-parameters/Scan- Networks.The name of the network can be read from LANmonitor or, for exam-

5.3.2Activate UMTS/GPRS profile

Operating the LANCOM devices with the UMTS/HSPDA function in varying locations or with different UMTS/GPRS data cards may well require different sets of settings. The relevant information for operating data cards is collected in a UMTS/HSPDA/GPRS profile. The profile can be switched very quickly via the interface settings for the UMTS interface.

The activation of the UMTS interface and the selection of the profile are to be found in LANconfig in the configuration area 'Interfaces' on the 'WAN' tab with the Interface settings button.

47

Image 47

Contents

Lancom 3550 Wireless Lancom Systems GmbH, Wuerselen Germany. All rights reserved Thank you for placing your trust in this Lancom product Security settingsThis documentation was compiled … Further server services DHCP, DNS, charge management Important instruction that should be followed Contents Point-to-point connections Setting up Internet accessSetting up the Umts profile Radio channel regulations for WLANs Options and accessoriesAppendix Which hardware to use? What is a Wireless LAN?Operation modes of Wireless LANs and base stations IntroductionLast mile via UMTS/HSPDA Advantages of the UMTS/HSPDA solutionInternet Mobile conference roomUMTS/HSPDA Backup Internet connection over DSL Applications What can your Lancom Router do?Wireless LAN Lancom System preconditions InstallationPackage contents Front side Status displays, interfaces an hardware installationStatus display Meanings of the LEDsGreen Red Blinking Time or connect-charge reached LED remains lit greenWireless link display can assume four different conditions Flashing Power-LED but no connection?Expert Configuration Setup Charges-module Nal wireless network card is not indicated on this displayBack of the unit Hardware installation Software installation Plexity considerably Which software should you install? Starting Lancom setupInstallation Which information is necessary? Basic configuration1 TCP/IP settings Information required for manual TCP/IP configuration New LAN-fully automatic configuration possibleConfigure manually nevertheless? Settings for the Wireless LAN Configuration protectionSelection of a radio channel Settings for the DSL connectionConnect charge protection LANconfig Start up LANconfig by clicking Start Programs LancomComplete the configuration with Finish Instructions for WEBconfigNetwork with Dhcp server Network without Dhcp serverOr with a name as discribed above Starting the wizards in WEBconfigWEBconfig main menu will be displayed Basic configuration Entering the password in the web browser TCP/IP settings to workstation PCsManual IP address assignment IP address assignment via the Lancom Router defaultIP address assignment via a separate Dhcp server Setting up Internet access LANconfig Quick access to the setup wizards Instructions for LANconfigBar, select Tools Setup Wizard Setting up Internet access Internet access Setting up the Umts profileSetting up the Umts profile Setting up the Umts profile VPN site coupling Setting up the Umts profile Choosing the mobile telephone network Other settingsActivate UMTS/GPRS profile UMTS/HSPDA only or automatic UMTS/HSPDA/GPRS selection Set up a time limit Point-to-point connections Configuration with LANconfig Configuration tool Menu/Table Connections under the following paths Access points in relay modeSecurity for point-to-point connections Encryption with 802.11i/WPAConfiguration area Wlan Security on the 802.11i/WEP tab Leps for P2P connections Found under WEBconfig or Telnet under the following pathsClosed network Security settingsSecurity for the Wireless LAN Lancom Enhanced Passphrase Security Access control via MAC addressEncryption of the data transfer  ensure that you have a secure connection 5 802.1x / EAPStandard WEP encryption IPSec over Wlan Tips for handling keysMand bar Extras Setup Wizard Security settings wizardWizard for LANconfig Firewall wizard Wizard for WEBconfigRules Security checklistConfiguration under WEBconfig Have you activated the Firewall? Have you assigned a password for the configuration?Have you permitted remote configuration? Have you assigned a password to the Snmp configuration?Have you closed critical ports with filters? Have you activated the IP masquerading?Security settings Security settings Antenna Diversity Options and accessoriesOptional Lancom Wireless Router antennas Lancom Public Spot Option Installation of AirLancer Extender antennasRadius PIN Handling TroubleshootingMenü/Tabelle Has the correct transfer protocol been selected? Problems with the cabling?You can monitor and correct the protocol settings under Increasing the TCP/IP window size under Windows DSL data transfer is slowUnwanted connections under Windows XP Appendix Performance data and specificationsWAN interface, 10/100base-TX Contact assignmentLAN interface, 10/100base-TX Declaration of conformity Radio channel regulations for WLANs Numerics LAN Link LAN Rx/Tx Power WAN Link WAN Status Wireless Link Connector cable LAN connectionNode/hub switch Optional antennas Options and accessories Relay function Remote configuration Reset15, 59 WAN connector WEBconfig PasswordWork Incorrect PIN PIN handling Time limit