Lancom Systems 3550 manual Configuration tool Menu/Table

Page 52

LANCOM 3550 Wireless

Chapter 6: Point- to- point connections

Activate the suitable point-to-point operation mode here and set the channel selection scheme to either 'Master' or 'Slave'. Enter the appropri- ate MAC address for the WLAN card at the remote station (maximum 6).

EN

other end of the connections are to be entered here! Not the access

point's own MAC address, and not the MAC addresses from any other interfaces that may be present in the access points.Please observe that only the MAC addresses of the WLAN cards at the

You will find the WLAN MAC address on a sticker below the corresponding antenna connector. Only use the string that is marked as the "WLAN MAC" or "MAC-ID". The other addresses that may be found are not the WLAN MAC address but the LAN MAC address.

Alternatively you will find the MAC addresses for the WLAN cards in the devices under WEBconfig, Telnet or a terminal program under the following paths:

Configuration tool	Menu/Table
WEBconfig	Expert configuration Status WLAN-statistics Inter-
	face-statistics

Terminal/Telnet	Status/WLAN-statistics/Interface-statistics

52

Image 52

Contents

Lancom 3550 Wireless Lancom Systems GmbH, Wuerselen Germany. All rights reserved Security settings Thank you for placing your trust in this Lancom productFurther server services DHCP, DNS, charge management This documentation was compiled … Important instruction that should be followed Contents Setting up the Umts profile Setting up Internet accessPoint-to-point connections Appendix Options and accessoriesRadio channel regulations for WLANs What is a Wireless LAN? Operation modes of Wireless LANs and base stationsIntroduction Which hardware to use?Advantages of the UMTS/HSPDA solution Last mile via UMTS/HSPDAMobile conference room InternetUMTS/HSPDA Backup Internet connection over DSL What can your Lancom Router do? ApplicationsWireless LAN Lancom Package contents InstallationSystem preconditions Status displays, interfaces an hardware installation Status displayMeanings of the LEDs Front sideLED remains lit green Green Red Blinking Time or connect-charge reachedFlashing Power-LED but no connection? Expert Configuration Setup Charges-moduleNal wireless network card is not indicated on this display Wireless link display can assume four different conditionsBack of the unit Hardware installation Software installation Plexity considerably Starting Lancom setup Which software should you install?Installation 1 TCP/IP settings Basic configurationWhich information is necessary? Configure manually nevertheless? New LAN-fully automatic configuration possibleInformation required for manual TCP/IP configuration Configuration protection Settings for the Wireless LANConnect charge protection Settings for the DSL connectionSelection of a radio channel Start up LANconfig by clicking Start Programs Lancom LANconfigInstructions for WEBconfig Complete the configuration with FinishNetwork without Dhcp server Network with Dhcp serverWEBconfig main menu will be displayed Starting the wizards in WEBconfigOr with a name as discribed above Basic configuration TCP/IP settings to workstation PCs Entering the password in the web browserIP address assignment via a separate Dhcp server IP address assignment via the Lancom Router defaultManual IP address assignment Setting up Internet access Bar, select Tools Setup Wizard Instructions for LANconfigLANconfig Quick access to the setup wizards Setting up Internet access Setting up the Umts profile Internet accessSetting up the Umts profile Setting up the Umts profile VPN site coupling Setting up the Umts profile Other settings Choosing the mobile telephone networkActivate UMTS/GPRS profile UMTS/HSPDA only or automatic UMTS/HSPDA/GPRS selection Set up a time limit Point-to-point connections Configuration with LANconfig Configuration tool Menu/Table Access points in relay mode Security for point-to-point connectionsEncryption with 802.11i/WPA Connections under the following pathsConfiguration area Wlan Security on the 802.11i/WEP tab Found under WEBconfig or Telnet under the following paths Leps for P2P connectionsSecurity for the Wireless LAN Security settingsClosed network Access control via MAC address Lancom Enhanced Passphrase SecurityEncryption of the data transfer Standard WEP encryption 5 802.1x / EAP ensure that you have a secure connection Tips for handling keys IPSec over WlanWizard for LANconfig Security settings wizardMand bar Extras Setup Wizard Wizard for WEBconfig Firewall wizardConfiguration under WEBconfig Security checklistRules Have you assigned a password for the configuration? Have you permitted remote configuration?Have you assigned a password to the Snmp configuration? Have you activated the Firewall?Have you activated the IP masquerading? Have you closed critical ports with filters?Security settings Security settings Optional Lancom Wireless Router antennas Options and accessoriesAntenna Diversity Installation of AirLancer Extender antennas Lancom Public Spot OptionRadius Troubleshooting PIN HandlingMenü/Tabelle You can monitor and correct the protocol settings under Problems with the cabling?Has the correct transfer protocol been selected? Unwanted connections under Windows XP DSL data transfer is slowIncreasing the TCP/IP window size under Windows Performance data and specifications AppendixLAN interface, 10/100base-TX Contact assignmentWAN interface, 10/100base-TX Declaration of conformity Radio channel regulations for WLANs Numerics Connector cable LAN connection Node/hub switch Optional antennas Options and accessoriesRelay function Remote configuration Reset LAN Link LAN Rx/Tx Power WAN Link WAN Status Wireless LinkWAN connector WEBconfig Password Work Incorrect PINPIN handling Time limit 15, 59