Fortinet 800/800F manual Introduction, Register your FortiGate unit

Page 7

 

 

 

Introduction

Register your FortiGate unit

Introduction

Welcome and thank you for selecting Fortinet products for your real-time network protection.

The FortiGate Unified Threat Management System improves network security, reduces network misuse and abuse, and helps you use communications resources more efficiently without compromising the performance of your network. The FortiGate Unified Threat Management System are ICSA-certified for firewall, IPSec, and antivirus services.

The FortiGate Unified Threat Management Systemis a dedicated, easily managed security device that delivers a full suite of capabilities, which include:

application-level services such as virus protection and content filtering

network-level services such as firewall, intrusion detection, VPN and traffic shaping

The FortiGate Unified Threat Management System uses Fortinet’s Dynamic Threat Prevention System (DTPS™) technology, which leverages breakthroughs in chip design, networking, security and content analysis. The unique ASIC-based architecture analyzes content and behavior in real-time, enabling key applications to be deployed right at the network edge where they are most effective at protecting your networks.

Register your FortiGate unit

Register the FortiGate unit by visiting http://support.fortinet.com and select Product Registration.

To register, enter your contact information and the serial numbers of the FortiGate units that you or your organization have purchased. You can register multiple FortiGate units in a single session without re-entering your contact information.

By registering your FortiGate unit, you will receive updates to threat detection and prevention databases (Antivirus, Intrusion Detection, etc.) and will also ensure your access to technical support.

For more information, see the Fortinet Knowledge Centre article “Registration Frequently Asked Questions” (http://kc.forticare.com/default.asp?id=2071).

FortiGate-800 and FortiGate-800F FortiOS 3.0 MR6 Install Guide

 

01-30006-0455-20080910

7

Image 7
Contents Install G U I D E Regulatory compliance TrademarksContents FortiGate Firmware Advanced configurationTesting new firmware before installing Installing firmware from a system reboot using the CLIIndex Page Register your FortiGate unit IntroductionAbout this document About the FortiGate-800/800FDocument conventions Typographic conventions Further ReadingFortinet Knowledge Center Customer service and technical supportComments on Fortinet technical documentation Environmental specifications InstallingRack mount instructions GroundingMounting To install the FortiGate unit into a rackPlugging in the FortiGate Connecting to the networkTo power on the FortiGate unit To power off the FortiGate unitNAT mode NAT vs. Transparent modeTo connect to the web-based manager Connecting to the FortiGate unitTransparent mode Connecting to the web-based managerTo connect to the CLI Connecting to the CLITo configure interfaces Go to System Network Interface Configuring NAT modeUsing the web-based manager Configure the interfacesAdding a default route and gateway Configure a DNS serverAdding firewall policies To modify the default gateway Go to Router StaticTo set an interface to use a static address Using the CLITo set an interface to use Dhcp addressing To set an interface to use PPPoE addressing To configure DNS server settingsTo add an outgoing traffic firewall policy To modify the default gatewaySwitching to Transparent mode Configuring Transparent modeTo switch to Transparent mode Go to System Status Source Address All Destination Interface To switch to Transparent mode Backing up the configuration Verify the configurationSet the time and date Restoring a configurationAdditional configuration Set the Administrator passwordUpdating antivirus and IPS signatures Configure FortiGuardAdditional configuration Protection profiles Advanced configurationFirewall policies Firewall policiesAntivirus options Configuring firewall policiesAntiSpam options Web filtering Logging Downloading firmware FortiGate FirmwareUpgrading the firmware Using the web-based managerReverting to a previous version Using the USB Auto-Install Backup and Restore from a USB keyTo revert to a previous firmware version To upgrade the firmware using the CLI Using the CLITo revert to a previous firmware version using the CLI Execute restore image namestr tftpip4Execute restore image namestr tftpipv4 Installing firmware from a system reboot using the CLIPress any key to display configuration menu To install firmware from a system rebootTo backup configuration using the CLI Restoring the previous configurationTo restore configuration using the CLI Additional CLI Commands for a USB keyTo configure the USB Auto-Install using the CLI To test the new firmware image Testing new firmware before installingTesting new firmware before installing Testing new firmware before installing Index Web filtering 35 web-based manager Page Page