Fortinet 60B manual Plugging in the FortiGate, Turning off the FortiGate unit, Mounting

Page 13

 

 

 

Installing

Plugging in the FortiGate

Mounting

If required to fit into a rack unit, remove the rubber feet from the bottom of the FortiGate unit.

Adhere the rubber feet included in the package to the underside of the FortiGate unit, near the corners of the device.

Place the FortiGate unit on any flat, stable surface. Ensure the unit has sufficient clearance on each side to ensure adequate airflow for cooling.

Plugging in the FortiGate

Use the following steps to connect the power supply to the FortiGate unit.

To power on the FortiGate unit

1Connect the AC adapter to the power connection at the back of the FortiGate unit.

2Connect the AC adapter to the power cable.

3Connect the power cable to a power outlet.

The FortiGate unit starts and the Power and Status LEDs light up. The Status LEDs flash while the FortiGate unit starts up, and remain lit when the system is running.

Connecting to the network

Using the supplied Ethernet cable, connect one end of the cable to your router or modem, whatever the connection is to the Internet. Connect the other end to the FortiGate unit. Connect to either the External, WAN port, or port 1. Connect additional cable to the Internal port or port 2 and your internal hub or switch.

Turning off the FortiGate unit

Always shut down the FortiGate operating system properly before turning off the power switch to avoid potential hardware problems.

To power off the FortiGate unit

1From the web-based manager, go to System > Status.

2In the Unit Operation display, select Shutdown, or from the CLI enter: execute shutdown

3Disconnect the power cables from the power supply.

FortiGate-60B FortiOS 3.0 MR6 Install Guide

 

01-30006-0446-20080910

13

Image 13
Contents Install G U I D E Regulatory compliance TrademarksContents Configuring the modem interface Advanced configurationConfiguring Transparent mode Protection profilesIndex FortiGate FirmwarePage Register your FortiGate unit IntroductionAbout this document About the FortiGate-60BDocument conventions Typographic conventions Further ReadingFortinet Knowledge Center Customer service and technical supportComments on Fortinet technical documentation Environmental specifications InstallingRack mount instructions GroundingPlugging in the FortiGate Connecting to the networkTurning off the FortiGate unit MountingTurning off the FortiGate unit NAT mode NAT vs. Transparent modeTransparent mode Connecting to the FortiGate unitConnecting to the web-based manager To connect to the web-based managerTo connect to the CLI Connecting to the CLIUsing the web-based manager Configuring NAT modeConfigure the interfaces To configure interfaces Go to System Network InterfaceAdding a default route and gateway Configure a DNS serverAdding firewall policies To modify the default gateway Go to Router StaticTo set an interface to use a static address Using the CLITo set an interface to use Dhcp addressing To set an interface to use PPPoE addressing To configure DNS server settingsTo modify the default gateway Configuring Transparent modeTo add an outgoing traffic firewall policy To switch to Transparent mode Go to System Status Switching to Transparent modeTo switch to Transparent mode To configure DNS server settings Backing up the configuration Verify the configurationAdditional configuration Restoring a configurationSet the Administrator password Set the time and dateUpdating antivirus and IPS signatures Configure FortiGuardAdditional configuration Protection profiles Advanced configurationFirewall policies Firewall policiesAntivirus options Configuring firewall policiesAntiSpam options Web filtering Logging Redundant mode Selecting a modem modeStand alone mode Configuring modem settingsDial on demand To configure modem settings Go to System Network ModemSyntax Configuring the modem using the CLIKeywords and variables Description Default Mode redudant Phone-number ExampleDead gateway detection Adding a Ping ServerConfiguring the Pcmcia modem card Administrative access through the modem portTo configure the modem Go to System Network Modem Adding firewall policies for modem connectionsAt+cpin=5555 Downloading firmware FortiGate FirmwareUpgrading the firmware Using the web-based managerReverting to a previous version Using the USB Auto-Install Backup and Restore from a USB keyTo revert to a previous firmware version To upgrade the firmware using the CLI Using the CLITo revert to a previous firmware version using the CLI Execute restore image namestr tftpip4Execute restore image namestr tftpipv4 Installing firmware from a system reboot using the CLIPress any key to display configuration menu To install firmware from a system rebootTo backup configuration using the CLI Restoring the previous configurationTo restore configuration using the CLI Additional CLI Commands for a USB keyTo configure the USB Auto-Install using the CLI To test the new firmware image Testing new firmware before installingTesting new firmware before installing Testing new firmware before installing Index System modem 43 system reboot, installing Page Page Page Page

60B specifications

The Fortinet FortiGate 60B is a compact, high-performance network security appliance designed for small to medium-sized businesses. As part of Fortinet's FortiGate series, the 60B integrates advanced security features and technologies, making it an ideal solution for organizations seeking to protect their networks from growing cyber threats.

One of the main features of the FortiGate 60B is its robust firewall capability. The device provides next-generation firewall (NGFW) functionalities, allowing businesses to monitor and control traffic at multiple layers. This includes application control, intrusion prevention, and web filtering, ensuring that only legitimate traffic is allowed access to critical resources. With a strong emphasis on threat detection, the 60B employs FortiGuard Labs' threat intelligence services to stay updated on the latest malware and attack vectors.

Another significant characteristic of the FortiGate 60B is its integrated virtual private network (VPN) capabilities. The device supports both site-to-site and remote access VPNs, enabling secure connections for remote employees and branch offices. This feature is essential for organizations that require secure communication over public networks, ensuring that sensitive data remains protected.

Performance is also a focal point of the FortiGate 60B. The appliance is equipped with dedicated hardware acceleration that optimizes throughput and minimizes latency. With impressive SSL inspection capabilities, it can handle encrypted traffic efficiently, making it well-suited for an increasingly secure internet landscape.

The FortiGate 60B also boasts extensive reporting and analytics features, enabling IT teams to gain valuable insights into network activity. This includes detailed logs and dashboards that help organizations identify potential security risks and respond to incidents in real time. In addition, the appliance is built with scalability in mind, allowing businesses to expand their security posture as they grow.

Furthermore, the FortiGate 60B is designed for ease of management. The unit can be configured and monitored through Fortinet's centralized management system, FortiManager, simplifying the administration of multiple devices across various locations.

In summary, the Fortinet FortiGate 60B is a powerful, versatile network security solution that combines advanced firewall capabilities, VPN support, and integrated threat intelligence. With its strong performance metrics and user-friendly management tools, it is an excellent choice for organizations aiming to bolster their cybersecurity defenses while maintaining operational efficiency.