Fortinet 60B manual Restoring a configuration, Additional configuration, Set the time and date

Page 28

Restoring a configuration

Configuring

Restoring a configuration

Should you need to restore the configuration file, use the following steps.

To restore the FortiGate configuration

1Go to System > Maintenance > Backup & Restore.

2Select to upload the restore file from your PC or a USB key.

The USB Disk option will be grayed out if the FortiGate unit supports USB disks but none are connected.

3Enter the path and file name of the configuration file, or select Browse to locate the file.

4Enter a password if required.

5Select Restore.

The FortiGate unit will load the configuration file and restart. Once the restart has completed, verify that the configuration has been restored.

Additional configuration

With the FortiGate connected and allowing traffic to pass-through, there are a few other configuration. While not mandatory, they will help in ensuring better control with the firewall.

Set the time and date

For effective scheduling and logging, the FortiGate system date and time must be accurate. You can either manually set the system date and time or configure the FortiGate unit to automatically keep its time correct by synchronizing with a Network Time Protocol (NTP) server.

To set the date and time

1Go to System > Status.

2Under System Information > System Time, select Change.

3Select your Time Zone.

4Optionally, select Automatically adjust clock for daylight saving changes.

5Select Set Time and set the FortiGate system date and time.

6If you want to synchronize the time with an NTP server, enable the option.

7Select OK.

Note: If you choose the option Automatically adjust clock for daylight saving changes, the system time must be manually adjusted after daylight savings time ends.

Set the Administrator password

The default administrator password is no password. You will want to apply a password to prevent anybody logging into the FortiGate and changing configuration options.

 

FortiGate-60B FortiOS 3.0 MR6 Install Guide

28

01-30006-0446-20080910

Image 28
Contents Install G U I D E Trademarks Regulatory complianceContents Advanced configuration Configuring the modem interfaceConfiguring Transparent mode Protection profilesFortiGate Firmware IndexPage Introduction Register your FortiGate unitAbout this document About the FortiGate-60BDocument conventions Further Reading Typographic conventionsFortinet Knowledge Center Customer service and technical supportComments on Fortinet technical documentation Installing Environmental specificationsGrounding Rack mount instructionsConnecting to the network Plugging in the FortiGateTurning off the FortiGate unit MountingTurning off the FortiGate unit NAT vs. Transparent mode NAT modeConnecting to the FortiGate unit Transparent modeConnecting to the web-based manager To connect to the web-based managerConnecting to the CLI To connect to the CLIConfiguring NAT mode Using the web-based managerConfigure the interfaces To configure interfaces Go to System Network InterfaceConfigure a DNS server Adding a default route and gatewayTo modify the default gateway Go to Router Static Adding firewall policiesTo set an interface to use a static address Using the CLITo set an interface to use Dhcp addressing To configure DNS server settings To set an interface to use PPPoE addressingTo modify the default gateway Configuring Transparent modeTo add an outgoing traffic firewall policy Switching to Transparent mode To switch to Transparent mode Go to System StatusTo switch to Transparent mode To configure DNS server settings Verify the configuration Backing up the configurationRestoring a configuration Additional configurationSet the Administrator password Set the time and dateConfigure FortiGuard Updating antivirus and IPS signaturesAdditional configuration Advanced configuration Protection profilesFirewall policies Firewall policiesConfiguring firewall policies Antivirus optionsAntiSpam options Web filtering Logging Selecting a modem mode Redundant modeConfiguring modem settings Stand alone modeTo configure modem settings Go to System Network Modem Dial on demandConfiguring the modem using the CLI SyntaxKeywords and variables Description Default Mode redudant Example Phone-numberAdding a Ping Server Dead gateway detectionAdministrative access through the modem port Configuring the Pcmcia modem cardTo configure the modem Go to System Network Modem Adding firewall policies for modem connectionsAt+cpin=5555 FortiGate Firmware Downloading firmwareUpgrading the firmware Using the web-based managerReverting to a previous version Using the USB Auto-Install Backup and Restore from a USB keyTo revert to a previous firmware version Using the CLI To upgrade the firmware using the CLIExecute restore image namestr tftpip4 To revert to a previous firmware version using the CLIInstalling firmware from a system reboot using the CLI Execute restore image namestr tftpipv4To install firmware from a system reboot Press any key to display configuration menuRestoring the previous configuration To backup configuration using the CLITo restore configuration using the CLI Additional CLI Commands for a USB keyTo configure the USB Auto-Install using the CLI Testing new firmware before installing To test the new firmware imageTesting new firmware before installing Testing new firmware before installing Index System modem 43 system reboot, installing Page Page Page Page

60B specifications

The Fortinet FortiGate 60B is a compact, high-performance network security appliance designed for small to medium-sized businesses. As part of Fortinet's FortiGate series, the 60B integrates advanced security features and technologies, making it an ideal solution for organizations seeking to protect their networks from growing cyber threats.

One of the main features of the FortiGate 60B is its robust firewall capability. The device provides next-generation firewall (NGFW) functionalities, allowing businesses to monitor and control traffic at multiple layers. This includes application control, intrusion prevention, and web filtering, ensuring that only legitimate traffic is allowed access to critical resources. With a strong emphasis on threat detection, the 60B employs FortiGuard Labs' threat intelligence services to stay updated on the latest malware and attack vectors.

Another significant characteristic of the FortiGate 60B is its integrated virtual private network (VPN) capabilities. The device supports both site-to-site and remote access VPNs, enabling secure connections for remote employees and branch offices. This feature is essential for organizations that require secure communication over public networks, ensuring that sensitive data remains protected.

Performance is also a focal point of the FortiGate 60B. The appliance is equipped with dedicated hardware acceleration that optimizes throughput and minimizes latency. With impressive SSL inspection capabilities, it can handle encrypted traffic efficiently, making it well-suited for an increasingly secure internet landscape.

The FortiGate 60B also boasts extensive reporting and analytics features, enabling IT teams to gain valuable insights into network activity. This includes detailed logs and dashboards that help organizations identify potential security risks and respond to incidents in real time. In addition, the appliance is built with scalability in mind, allowing businesses to expand their security posture as they grow.

Furthermore, the FortiGate 60B is designed for ease of management. The unit can be configured and monitored through Fortinet's centralized management system, FortiManager, simplifying the administration of multiple devices across various locations.

In summary, the Fortinet FortiGate 60B is a powerful, versatile network security solution that combines advanced firewall capabilities, VPN support, and integrated threat intelligence. With its strong performance metrics and user-friendly management tools, it is an excellent choice for organizations aiming to bolster their cybersecurity defenses while maintaining operational efficiency.