Fortinet 60B Switching to Transparent mode, To switch to Transparent mode Go to System Status

Page 24

Configuring Transparent mode

Configuring

Using the web-based manager

After connecting to the web-based manager, you can use the following procedures to complete the basic configuration of the FortiGate unit. Ensure you read the section “Connecting to the web-based manager” on page 16 before beginning.

Switching to Transparent mode

The FortiGate unit comes preset to NAT mode. You need to switch to Transparent mode.

To switch to Transparent mode

1Go to System > Status.

2Select Change beside the Operation Mode.

3Select Transparent.

4Enter the Management IP/Netmask address and the Default Gateway address.

The default gateway IP address is required to tell the FortiGate unit where to send network traffic to other networks.

5Select Apply.

Configure a DNS server

A DNS server is a service that converts symbolic node names to IP addresses. A domain name server (DNS server) implements the protocol. In simple terms, it acts as a phone book for the Internet. A DNS server matches domain names with the computer IP address. This enables you to use readable locations, such as fortinet.com when browsing the Internet.

DNS server IP addresses are typically provided by your internet service provider.

To configure DNS server settings

1Go to System > Network > Options.

2Enter the IP address of the primary DNS server.

3Enter the IP address of the secondary DNS server. Select Apply.

Adding firewall policies

Firewall policies enable traffic to flow through the FortiGate interfaces. Firewall policies define the FortiGate unit process the packets in a communication session. You can configure the firewall policies to allow only specific traffic, users and specific times when traffic is allowed.

For the initial installation, a single firewall policy that enables all traffic through will enable you to verify your configuration is working. On lower-end units such a default firewall policy is already in place. For the higher end FortiGate units, you will need to add a firewall policy.

The following steps add two policies that allows all traffic through the FortiGate unit, to enable you to continue testing the configuration on the network.

 

FortiGate-60B FortiOS 3.0 MR6 Install Guide

24

01-30006-0446-20080910

Image 24
Contents Install G U I D E Trademarks Regulatory complianceContents Advanced configuration Configuring the modem interfaceConfiguring Transparent mode Protection profilesFortiGate Firmware IndexPage Introduction Register your FortiGate unitAbout the FortiGate-60B About this documentDocument conventions Further Reading Typographic conventionsCustomer service and technical support Fortinet Knowledge CenterComments on Fortinet technical documentation Installing Environmental specificationsGrounding Rack mount instructionsConnecting to the network Plugging in the FortiGateTurning off the FortiGate unit MountingTurning off the FortiGate unit NAT vs. Transparent mode NAT modeConnecting to the FortiGate unit Transparent modeConnecting to the web-based manager To connect to the web-based managerConnecting to the CLI To connect to the CLIConfiguring NAT mode Using the web-based managerConfigure the interfaces To configure interfaces Go to System Network InterfaceConfigure a DNS server Adding a default route and gatewayTo modify the default gateway Go to Router Static Adding firewall policiesUsing the CLI To set an interface to use a static addressTo set an interface to use Dhcp addressing To configure DNS server settings To set an interface to use PPPoE addressingConfiguring Transparent mode To modify the default gatewayTo add an outgoing traffic firewall policy Switching to Transparent mode To switch to Transparent mode Go to System StatusTo switch to Transparent mode To configure DNS server settings Verify the configuration Backing up the configurationRestoring a configuration Additional configurationSet the Administrator password Set the time and dateConfigure FortiGuard Updating antivirus and IPS signaturesAdditional configuration Advanced configuration Protection profilesFirewall policies Firewall policiesConfiguring firewall policies Antivirus optionsAntiSpam options Web filtering Logging Selecting a modem mode Redundant modeConfiguring modem settings Stand alone modeTo configure modem settings Go to System Network Modem Dial on demandConfiguring the modem using the CLI SyntaxKeywords and variables Description Default Mode redudant Example Phone-numberAdding a Ping Server Dead gateway detectionAdministrative access through the modem port Configuring the Pcmcia modem cardTo configure the modem Go to System Network Modem Adding firewall policies for modem connectionsAt+cpin=5555 FortiGate Firmware Downloading firmwareUsing the web-based manager Upgrading the firmwareReverting to a previous version Backup and Restore from a USB key Using the USB Auto-InstallTo revert to a previous firmware version Using the CLI To upgrade the firmware using the CLIExecute restore image namestr tftpip4 To revert to a previous firmware version using the CLIInstalling firmware from a system reboot using the CLI Execute restore image namestr tftpipv4To install firmware from a system reboot Press any key to display configuration menuRestoring the previous configuration To backup configuration using the CLIAdditional CLI Commands for a USB key To restore configuration using the CLITo configure the USB Auto-Install using the CLI Testing new firmware before installing To test the new firmware imageTesting new firmware before installing Testing new firmware before installing Index System modem 43 system reboot, installing Page Page Page Page

60B specifications

The Fortinet FortiGate 60B is a compact, high-performance network security appliance designed for small to medium-sized businesses. As part of Fortinet's FortiGate series, the 60B integrates advanced security features and technologies, making it an ideal solution for organizations seeking to protect their networks from growing cyber threats.

One of the main features of the FortiGate 60B is its robust firewall capability. The device provides next-generation firewall (NGFW) functionalities, allowing businesses to monitor and control traffic at multiple layers. This includes application control, intrusion prevention, and web filtering, ensuring that only legitimate traffic is allowed access to critical resources. With a strong emphasis on threat detection, the 60B employs FortiGuard Labs' threat intelligence services to stay updated on the latest malware and attack vectors.

Another significant characteristic of the FortiGate 60B is its integrated virtual private network (VPN) capabilities. The device supports both site-to-site and remote access VPNs, enabling secure connections for remote employees and branch offices. This feature is essential for organizations that require secure communication over public networks, ensuring that sensitive data remains protected.

Performance is also a focal point of the FortiGate 60B. The appliance is equipped with dedicated hardware acceleration that optimizes throughput and minimizes latency. With impressive SSL inspection capabilities, it can handle encrypted traffic efficiently, making it well-suited for an increasingly secure internet landscape.

The FortiGate 60B also boasts extensive reporting and analytics features, enabling IT teams to gain valuable insights into network activity. This includes detailed logs and dashboards that help organizations identify potential security risks and respond to incidents in real time. In addition, the appliance is built with scalability in mind, allowing businesses to expand their security posture as they grow.

Furthermore, the FortiGate 60B is designed for ease of management. The unit can be configured and monitored through Fortinet's centralized management system, FortiManager, simplifying the administration of multiple devices across various locations.

In summary, the Fortinet FortiGate 60B is a powerful, versatile network security solution that combines advanced firewall capabilities, VPN support, and integrated threat intelligence. With its strong performance metrics and user-friendly management tools, it is an excellent choice for organizations aiming to bolster their cybersecurity defenses while maintaining operational efficiency.