Extreme Networks Px Series manual 1Client IP persistence mode

Page 62

145.12.1.164.1.1.7

Client

www.buystuff.com

Figure 6-1:Client IP persistence mode

The following transactions occur in Figure 6-1:

The client with IP address 145.12.1.1 transmits its first TCP request to www.buystuff.com at its VIP address, 64.1.1.7.

Server 1

Server 2

Server 3

WS_001

Using its configured load balancing policy, the Px series application switch selects server 3 as the web server.

The application switch sends the first request to the selected web server.

The server sends a request back to the client via the application switch, thus establishing a session between the server and the client.

The client sends another request.

The application switch examines the IP address, sees that the request is from client 125.12.1.1.

The application switch forwards the request to server 3.

This scenario continues until the session persistence times out.

Client IP persistence mode requires that the IP address of the client remain the same for the entire session. It does not work if the client IP address changes dynamically within a session; for example, for large ISPs that conserve IP addresses by using a single proxy address for many different clients. In this case, use one of the cookie persistence modes.

6-4

Px Series Application Switch Installation and Configuration Guide

Image 62
Contents Published April Part number 100101-00 Rev Page Contents Installing the PxM Application Switch Module Configuring Servers and Services Index Index of Commands Preface IntroductionIcon Alerts you to ConventionsText Conventions Convention DescriptionRelated Publications Preface Server Load Balancing Concepts Purpose of Server Load BalancingTerms 1Conceptual view of server load balancingLoad Balancing Modes Layer 4 Load BalancingLayer 7 Load Balancing and Content Analysis 2Single client-server transaction using layer3Establishing a layer 7 request Getting Started on Load Balancing Configuration Port RewriteGetting Started on Load Balancing Configuration Page SummitPx1 Front View Installing the SummitPx1 Application SwitchOverview of the SummitPx1 Application Switch 1Px series application switch LEDs Color Indicates2DB-9 Adapter Pinouts SummitPx1 Application Switch Rear ViewSignal Description To DB-9Rack Mounting Installing the SummitPx1 Application SwitchDetermining the Location Powering On the SummitPx1 Free-StandingSetting Up Console Communication Configuring Switch IP Parameters Configuring the 10/100 Ethernet Management Port Installing the PxM Application Switch Module Installing I/O ModulesRemoving I/O Modules Removing I/O Modules Page Managing the Switch Syntax Symbols Using the Command-Line InterfaceAbbreviated Syntax and Command Completion 1Command Syntax SymbolsSpecifying Text Values Symbol DescriptionLine-Editing Keys 2Line-Editing KeysPrompt Text Configuring Management AccessCommand History Changing the Default Passwords Creating Accounts Modifying AccountsCommand Description Managing the PxMConfiguring VLANs Setting Description System Configuring Snmp4SNMP Configuration Settings ContactConfiguring DNS Client Services SettingDescriptionUsing Secure Shell 2 SSH2 5DNS Client Configuration CommandsEnabling SSH2 for Inbound Switch Access Config ssh2 keyUsing SCP2 from an External SSH2 Client SSH2 Client Functions on the Switch Checking Basic Connectivity UtilitiesShowing CPU Load Logging Configuring a Startup Banner Message Starting the GlobalPx Content Director AgentExample Configuration Internet DNS serverFollowing commands configure all system-related facilities Page Configuring Servers and Services Configuring Real ServersConfiguring Server Groups Configuring Virtual Services Layer 7 Virtual Services Layer 4 Port-based Load BalancingConfiguring Traffic Tagging Tag Specification Description Tag Range Configuration Example1Tag Specifications Configuration Example Page Choosing Policies, Persistence Modes, and NAT Scheduling PoliciesSpecifier Policy Description Persistence Modes1Scheduling Policies Client IP Persistence Mode UDP Flow Persistence1Client IP persistence mode Configuring Client IP Stickiness Cookie Persistence Modes2Self-identifying cookie persistence mode Persistence Modes Hashed Cookie Persistence Session Learned Cookie Persistence Mode 4Learned cookie persistence mode Configuring Cookie Stickiness SSL Session Identifier Persistence Full-NAT Mode NAT ModesServer-only Half-NAT Mode Configuring Full-NAT Mode and Proxy IP AddressesConfiguring Half-NAT Mode Config source-flow name next-hop gateway-mode ip Real Syslog server SummitPx1 Configuration Example Page URL Switching Domain and URL SwitchingDomain Switching 1Typical switching scenario2Domain switching example Configuring URL Switching URL Switching3Simple URL switching example 4More Complicated URL switching example 5Hierarchical approach to pattern rules Wildcard Example Definition Creating Domain and URL Switching Rules1Wildcard Combinations Modifying Existing URL Rules and Domains Application Servers Management net Configuration Example Page Configuring Redundancy Using Vrrp with the SummitPx1Adding and Configuring VRRPs Give backup systems lower prioritiesUsing Vrrp in Existing Redundant Networks 1Application switch using multiple VLANs Vrrp Automatic SynchronizationFollowing commands can be passed from master to backup Configuring Redundancy for the PxM Using Esrp with the PxMConfiguring the PxM for Multiple VLANs For SW2Configuring a Default Gateway Health Checks OverviewServer Startup Pacing Health Checking Procedure Types of Health Checks Configuring Health ChecksTimers and Counters You can disable health checks for a server group Page Showing Traffic Statistics Monitoring the Switch1Statistics Display Commands Displays packet-level counters for Showing Configuration Details 2Configuration Display CommandsConfiguration Displays Status Displays SummitPx128 # show server detailsShow health Information Column DescriptionManaging and Troubleshooting Operation 5Management and Troubleshooting CommandsCommandDescription Index EsrpHttp GET AUX Page Index of Commands