Dialogic®
Physical Description
IP Board
Quick Install Card
Part number
Copyright ©
Dialogic Corporation.
All Rights Reserved.
Before You Begin
Protecting the Board from Damage
CAUTION: All computer boards are sensitive to electrostatic discharge (“ESD”). Handle all
Board
Extractor
POWER
|
| 1 | 2 |
| A |
| RED |
Alarm | L |
| YEL |
M |
| LOOP | |
| A |
| CARR |
Status | R |
| SGNL |
S | 3 | 4 | |
| S |
|
|
LEDs | / |
|
|
A |
| RED | |
| T |
|
|
| T |
| YEL |
| U |
| |
| S |
| CARR |
|
| SGNL | |
|
|
| LOOP |
OUT OF
SERVICE
Board | Daughterboard | Baseboard |
|
| |
Extractor |
|
|
Faceplate | Compact PCI Board |
(front view) |
|
P5
P4
P1
E th e rn e t |
|
In te rfa c e |
|
C o n n e c to r |
|
P 5 |
|
| Trunk 1 |
J 1 | T ru n k 2 |
R J | T ru n k 3 |
| |
| T ru n k 4 |
P 2 |
|
| E th e rn e t |
|
| In te rfa c e |
|
P 5 | C o n n e c to r |
|
|
| |
B N C C o n n e c to rs | P 2 | |
|
| |
|
| |
Rear I/O Module |
| |
observe
If you are not familiar with ESD safety precautions, visit
http://www.dialogic.com/support/hwinstall to learn more.
Unpacking the Board
Unpack the Dialogic®
1. | Prepare a |
2. | Carefully remove the board from the shipping |
| carton and |
| board by the edges and avoid touching the board’s |
| components. |
Compact PCI Baseboard
Part: | Function: |
Power LED | Indicates board is powered up. |
Red Alarm LEDs | Not functional in this assembly. |
Yellow Alarm LEDs | Not functional in this assembly. |
Carrier Signal LEDs | Not functional in this assembly. |
Loopback LEDs | Not functional in this assembly. |
Out of Service LED | Indicates board is out of service |
| or in reset from host. |
P1, P4, P5 | Compact PCI board connectors |
| to backplane. |
Rear I/O Modules
Part: | Function: |
Not functional in this assembly. | |
P2 | Telephony network interface test port |
P5 | Rear I/O module connector to Compact PCI |
| backplane |
BNC | Not functional in this assembly |
Connectors |
|
Ethernet | Connection to Ethernet network |
Connector |
|
3. Lay the board on the |
surface. |
Note: Place boards in
NOTES: Rear I/O Modules are ordered separately and are available in two different forms depending on the type of connectors used, guided or unguided. Select a Rear I/O Module that is compatible with your chassis type. See the PICMG 2.0 D3.0 Compact PCI Specification for more information on guided and unguided connectors.
CAUTION: Do not remove the board from the
Installing the Hardware
NOTE: In a Windows environment, install the software first, the hardware second, and then run the Dialogic® Configuration Manager (DCM) to configure the system.
1.Turn the power to the chassis OFF if you do not have a live insertion system. If you do have live insertion capability, the power to the chassis can remain ON.
2.Remove the chassis cover plate or open the front door.
3.Select an empty expansion bus slot.
NOTE: When power is on, the Rear I/O module should be installed first, before the main board.
4.Install the Rear I/O module in the rear of the slot selected in step 3. Use the slot’s board guides as you insert the board into the chassis slot. Make sure that the tabs on the board extractors engage the guide holes in the chassis card cage, then lock down the board extractors until the red locking tabs snap shut.
CAUTION
cPCI backplane pins are bent easily. Make sure that the board is seated with hand pressure before fully seating board. If board extractors are used to seat the board, make sure to seat evenly.
5.Install the board in the front of the slot selected in step 3. Use the slot’s board guides as you insert the board into the chassis slot. Make sure that the tabs on the board extractors engage the guide holes in the chassis card cage, then lock down the board extractors until the red locking tabs snap shut.
NOTE: If the power to the chassis is on, power is automatically applied to the board, the Out of Service LED lights briefly and then goes out, and the Power LED goes on.
6.Tighten the retaining screws to secure the board firmly in the chassis slot (optional).
7.Select a new slot and repeat steps