Dialogic manual DM/F240-1T1-PCI DM/F300-1E1-PCI, Before You Begin, Configuring the Hardware

Page 1

Dialogic®

DM3 Fax Boards

Quick Install Card for PCI

DM/F240-1T1-PCI

DM/F300-1E1-PCI

Part number 64-0044-02

Copyright © 2002-2007

Dialogic Corporation.

All Rights Reserved.

Before You Begin

Protecting the Board from Damage

Caution! All computer boards are sensitive to electrostatic discharge (“ESD”). Handle all static-sensitive boards and components at a static-safe work area, and observe anti-static precautions at all times.

If you are not familiar with ESD safety precautions, visit http://www.dialogic.com/support/hwinstall to learn more.

Unpacking the Board

Unpack the Dialogic® DM3 Fax Board (“board”) according to the following steps:

Red

Yellow

Green

Loopback

5

3 4

2

1

CH4 CH3 CH2 CH1

Physical Description

 

1.

RJ-48C Jack: Connector to external

 

8

digital telephone network interface.

 

General Network Interface Alarm LED

 

2.

 

3.

Power LED

7

4.

Reset LED

6

5.

SW1: Rotary switch to set board

 

identification (LINUX systems only).

 

 

 

6.

Alarm LEDs: Indicate network alarms for

 

 

trunk 1 (CH1).

 

 

Red: Indicates loss of signal.

9Yellow: Indicates loss of frame synchronization at far end of external

network.

10Green: Indicates signal present; powered up and receiving signal from external sources.

Loopback: Indicates loopback mode is activated.

LEDs also indicate POST status.

7. CT/MVIP Bus Termination Jumpers*:

Bus signal is terminated when the

JP2Acorresponding jumper clip is installed.

JP2B

JP2A: CT Bus termination jumper

JP2B: MVIP Bus termination jumper

8. P3: CT Bus connector

9. ISA Edge Retainer

10. Signal Processing Daughterboard

*Note: Signal must be terminated only on boards at each end of the CT Bus cable.

1.Prepare a static-safeguarded work area.

2.Carefully remove the board from the shipping carton and anti-static packaging. Handle the board by the edges and avoid touching the board’s components.

3.Lay the board on the static-dissipative work surface.

Note: Place boards in static-shielding bags when carrying boards from station to station.

CAUTION: Do not remove the board from the anti-static packaging until you are ready to install it. Observe proper anti-static precautions at all times.

Configuring the Hardware

Board Identification

The DM3 device driver, part of the system software, assigns board instance numbers in ascending order (beginning with 0) as it detects each board in your system. A board instance

number is the identification (ID) number used by the system software to recognize the board.

NOTE: If you add or remove a board, the system may change the existing board instance (ID) numbers.

Windows System

After the hardware and the system software are installed, refer to the Dialogic® Configuration Manager (DCM) utility to retrieve the board instance (ID) number(s) assigned to the board(s) in your system.

See the DCM online help for more details about board identification.

Linux System

In a Linux system, you must set SW1 to a unique number for each DM3 board in your system. Use a non-magnetic screwdriver to turn SW1 to 1 of 16 board settings, 0-9 or A-F.

After the hardware and system software are installed, refer to the proper configuration files to retrieve the board instance (ID) number(s) assigned to the board(s) in your system.

For more information about Linux configuration files, see the Software Installation Reference.

Installing the Hardware

NOTE: You should install the hardware before the system software. However, if you are adding DM3 hardware to an existing DM3 system, you do not need to uninstall existing DM3 software.

1.With your computer on the static-safe work area, switch off the power and disconnect all power cords from the electrical outlets.

2.Remove the computer cover.

3.Select an empty PCI expansion bus slot and remove the slot’s retaining screw and access cover plate (if applicable).

Image 1
Contents Installing the Hardware Configuring the HardwareDM/F240-1T1-PCI DM/F300-1E1-PCI Before You BeginWarranty and Return Information After Installing HardwareWarranty Period Contacting Technical Support Sales Assistance

DM/F300-1E1-PCI, DM/F240-1T1-PCI specifications

The Dialogic DM/F300-1E1-PCI and DM/F240-1T1-PCI are advanced telecommunication interface cards designed for seamless connectivity in voice and data applications. These cards are part of Dialogic’s extensive portfolio and serve as robust solutions for various networking needs, particularly in telephony and data communications systems.

One of the standout features of the DM/F300-1E1-PCI card is its ability to support E1 connections. It provides users with a reliable interface capable of handling up to 30 voice channels, making it ideal for organizations that require high-density communication. The card operates with advanced signaling protocols including ISDN and CAS, which ensures compatibility with a wide range of telephony systems.

Conversely, the DM/F240-1T1-PCI card focuses on T1 connections, supporting up to 24 voice channels. This flexibility allows businesses to tailor their communication strategies based on their specific infrastructure and service requirements. Both cards leverage Dialogic's proprietary technologies, providing superior voice quality, echo cancellation, and call handling capabilities.

In terms of installation and integration, these cards feature a PCI interface that is straightforward to integrate into existing systems. Their design ensures compatibility with a variety of operating systems, enhancing their usability across multiple platforms. Additionally, the DM/F300 and DM/F240 cards offer extensive debugging and diagnostics capabilities, which simplify troubleshooting and maintenance tasks.

Their versatility is further enhanced with support for common voice applications such as Interactive Voice Response (IVR), automatic call distribution (ACD), and unified communications. This makes them suitable for various environments ranging from call centers to enterprise telephony, allowing organizations to improve customer interaction and operational efficiency.

Moreover, both cards support multiple-channel voice coding, including G.711, G.729, and G.723. This allows users to effectively balance voice quality and bandwidth usage, adapting to specific business needs while ensuring cost-efficiency.

In summary, the Dialogic DM/F300-1E1-PCI and DM/F240-1T1-PCI cards are engineered to provide high-density, high-quality voice and data communication. With their extensive features, compatibility with various signaling protocols, and support for multiple voice applications, these interface cards stand out as essential components in modern telecommunications infrastructure. Their capabilities empower businesses to improve communication efficiency and enhance customer experiences across diverse platforms.