Cabling Information
The cables included with your adapter are designed with custom components and cannot be indepen- dently manufactured. If you require multiple periph- eral cables of one type, you may order additional cables from Digi. To extend the length of a Digi cable, use standard interface cabling between the end of Digi’s cable and the peripheral.
Interface Pinouts
Each cable provided by Digi has a
Pin | Description | Pin | Description |
2 | TXD | 20 | DTR |
3 | RXD | 6 | DSR |
15 | TXCIN | 8 | DCD |
17 | RXC | 24 | TXCOUT |
4 | RTS | 22 | RI |
5 | CTS | 7 | GND |
1 and | CGND |
|
|
shell |
|
|
|
V.35, Male 34-pin Connector
Pin | Description | Pin | Description |
A | CGND | R | RXD(A) |
B | GND | T | RXD(B) |
C | RTS | U | TXCLKOUT(A) |
D | CTS | W | TXCLKOUT(B) |
E | DSR | V | RXCLK(A) |
F | DCD | X | RXCLK(B) |
H | DTR | Y | TXCLKIN(A) |
P | TXD(A) | AA | TXCLKIN(B) |
S | TXD(B) |
|
|
X.21, Male DB-15 Connector
Pin | Description | Pin | Description |
2 | TXD(A) | 12 | Indicator(B) |
9 | TXD(B) | 6 | SETI(A)* |
3 | Control(A) | 13 | SETI(B)* |
10 | Control(B) | 7 | SETO(A)** |
4 | RXD(A) | 14 | SETO(B)** |
11 | RXD(B) | 8 | Signal Ground |
5 | Indicator(A) | 1 and | CGND |
|
| shell |
|
*SETI=Signal Element Timing In
**SETO=Signal Element Timing Out
EIA-530, Male DB-25 Connector
Pin | Description | Pin | Description |
2 | TXD(A) | 13 | CTS(B) |
14 | TXD(B) | 20 | DTE Ready(A) |
3 | RXD(A) | 23 | DTE Ready(B) |
16 | RXD(B) | 6 | DCE Ready(A) |
15 | TXCLKIN(A) | 22 | DCE Ready(B) |
12 | TXCLKIN(B) | 8 | RLSD(A)* |
17 | RXCLK(A) | 10 | RLSD(B)* |
9 | RXCLK(B) | 24 | TXCLKOUT(A) |
4 | RTS(A) | 11 | TXCLKOUT(B) |
19 | RTS(B) | 7 | Signal Ground |
5 | CTS(A) | 1 and | CGND |
|
| shell |
|
| * RLSD=Received Line Signal Detector | ||
Regulatory Notices
Federal Communications Commission (FCC) Statement
Radio Frequency Interference (RFI) (FCC 15.105)
This device has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 Subpart B, of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter- ference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accor- dance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Labeling Requirements (FCC 15.19)
This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Modifications (FCC 15.21)
Changes or modifications to this equipment not expressly approved by Digi may void the user’s authority to operate this equipment.
Declaration Of Conformity
(In accordance with FCC Dockets
Manufacturer’s Name: | Digi International |
Corporate Headquarters: | 11001 Bren Road East |
| Minnetonka MN 55343 |
Manufacturing Headquarters: 10000 West 76th Street | |
| Eden Prairie MN 55344 |
Digi International declares, that the product: | |
Product Name: | SYNC/570i PCI |
Model Numbers: | |
| 63000002, 63000003, |
| 63000004 and/or 63000008 |
To which this declaration relates, meets the requirements specified by the Federal Communications Commission as detailed in the following specifi- cations
•Part 15, Subpart B, for Class B Equipment
•FCC Docket
The product listed above has been tested at an External Test Laboratory certified per FCC rules and has been found to meet the FCC, Part 15, Class
B, Emission Limits. Documentation is on file and available from the Digi International Homologation Department.
Tested to Comply
With FCC Standards
FOR HOME OR OFFICE USE
Industry Canada
This Class B digital apparatus meets the requirements of the Canadian Interference Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le máteriel brouilleur du Canada.
European EMC Standards
This device meets the following electromagnetic emissions standards:
•EN55022
•
European TTE Standard
This device meets the
Safety Standards
This device meets the following safety standards:
•UL 1950
•CSA 22.2 No. 950
•EN60950
SYNC/570i (PCI) Installation Card | SYNC/570i | SYNC/570i (PCI) Installation Card | SYNC/570i |