Fortinet 800F manual Using the command line interface, To add a default gateway to an interface

Page 31

NAT/Route mode installation

Configuring the FortiGate unit to operate in NAT/Route mode

 

 

2Use the up and down arrows to highlight the name of the interface to change and press Enter.

3Press Enter for IP address.

4Use the up and down arrow keys to increase or decrease the value of each IP address digit. Press Enter to move to the next digit. Press Esc to move to the previous digit.

Note: When you enter an IP address, the LCD always shows three digits for each part of the address. For example, the IP address 192.168.100.1 appears on the LCD as 192.168.100.001. The IP address 192.168.23.45 appears as 192.168.023.045.

5After you set the last digit of the IP address, press Enter.

6Use the down arrow to highlight Netmask.

7Press Enter and change the Netmask.

8After you set the last digit of the Netmask, press Enter.

9Press Esc to return to the Main Menu.

To add a default gateway to an interface

The default gateway is usually configured for the interface connected to the Internet.

You can use the procedure below to configure a default gateway for any interface.

1Press Enter to display the interface list.

2Use the down arrow key to highlight the name of the interface connected to the Internet and press Enter.

3Use the down arrow to highlight Default Gateway.

4Press Enter and set the default gateway.

5After you set the last digit of the default gateway, press Enter.

6Press Esc to return to the Main Menu.

You have now completed the initial configuration of the FortiGate unit and you can proceed to “Next steps” on page 39.

Using the command line interface

You can also configure the FortiGate unit using the command line interface (CLI). For information about connecting to the CLI, see “Connecting to the command line interface (CLI)” on page 17.

Configuring the FortiGate unit to operate in NAT/Route mode

Use the information that you gathered in Table 6 on page 28 to complete the following procedures.

To add/change the administrator password

1Log in to the CLI.

2Change the admin administrator password. Enter:

FortiGate-800/800F Installation Guide

01-28006-0024-20041026

31

Image 31
Contents October 01-28006-0024-20041026 Installation GuideRegulatory Compliance TrademarksTable of Contents Index Introduction Secure installation, configuration, and managementWeb-based manager Command line interfaceDocument conventions Setup wizardFortiGate documentation FortiGate Installation GuideFortiMail documentation Related documentationFortiManager documentation FortiClient documentationComments on Fortinet technical documentation FortiLog documentationCustomer service and technical support Comments on Fortinet technical documentation Getting started Package contents Mounting Connecting to the web-based manager Turning the FortiGate unit power on and offTo power off the FortiGate unit To connect to the web-based manager Connecting to the command line interface CLIWelcome To connect to the CLIFactory default NAT/Route mode network configuration Factory default FortiGate configuration settingsNetwork Settings Factory default Transparent mode network configurationFactory default protection profiles Factory default firewall configurationWeb protection profile settings NAT/Route mode Planning the FortiGate configurationTransparent mode NAT/Route mode with multiple external network connectionsWeb-based manager and setup wizard Configuration optionsFront control buttons and LCD Next steps Preparing to configure the FortiGate unit in NAT/Route mode NAT/Route mode installationDMZ Dhcp or PPPoE configurationConfiguring basic settings Using the web-based managerTo configure interfaces Go to System Network Interface Go to System Router Static Using the front control buttons and LCDTo configure DNS server settings Go to System Network DNS To add a default routeTo add/change the administrator password Using the command line interfaceConfiguring the FortiGate unit to operate in NAT/Route mode To add a default gateway to an interfaceExample To configure interfacesGet system interface To configure DNS server settingsOn page 28 and on page 29 for other settings Using the setup wizardDhcp server Starting the setup wizardFortiGate-800 Connecting the FortiGate unit to the networksFortiGate-800F To connect to FortiGate-800/800F user-defined interfaces To connect the FortiGate unit running in NAT/Route modeConfiguring the networks To set the date and time Go to System Config TimeTo register the FortiGate unit Go to System Maintenance Update Center To configure virus, attack, and spam definition updatesPreparing to configure Transparent mode Transparent mode installationTo change the Management IP Go to System Network Management To change the management IP address and netmask Reconnecting to the web-based managerTo change to Transparent mode using the CLI To add a default gatewayTo configure the management IP address End To configure the default gatewayTo start the setup wizard Connecting the FortiGate unit to your networkFortiGate-800F Internal Network Other Network To register your FortiGate unit Reconnecting to the web-based manager Priorities of heartbeat device and monitor priorities High availability installationConfiguring FortiGate units for HA operation High availability configuration settingsGroup ID MAC Address To change the FortiGate unit host name High availability settings ScheduleConfig system global Set hostname namestr end Configuring FortiGate units for HA using the CLITo configure the FortiGate unit for HA operation Connecting the cluster to your networksTo connect the cluster Internal Network Installing and configuring the clusterConfiguring FortiGate units for HA using the CLI CLI IndexIndex 01-28006-0024-20041026

800F, 800 specifications

Fortinet, a leader in cybersecurity solutions, has made significant strides in fortifying enterprise networks with its FortiGate 800 and 800F series. These next-generation firewalls are designed to deliver high performance and security for organizations seeking to protect their critical assets while ensuring optimal network efficiency.

The FortiGate 800 and 800F series are built on Fortinet's proprietary Security Fabric architecture, which provides a consolidated approach to security. This architecture allows organizations to leverage seamless integration across various security solutions and services, enhancing visibility and control. With a focus on scalability, these models support various deployment scenarios—from branch offices to data centers—making them versatile options for organizations of any size.

One of the standout features of the FortiGate 800 and 800F series is their robust threat intelligence capabilities. Powered by FortiGuard Labs, these firewalls provide real-time threat intelligence that enables proactive threat mitigation and incident response. This not only helps to defend against known threats but also enhances the firewall’s ability to identify emerging threats, ensuring comprehensive protection.

The series boasts impressive performance metrics. The FortiGate 800F can process up to 20 Gbps of firewall throughput and 1.5 million concurrent sessions, making it a suitable choice for high-performance environments. Additionally, the built-in SSL inspection capabilities allow organizations to decrypt and inspect encrypted traffic, which is crucial for detecting hidden threats.

The FortiGate 800 and 800F also feature advanced security technologies, including Intrusion Prevention System (IPS), antivirus, web filtering, and application control, all managed through a unified interface. This centralization simplifies management and reduces administrative overhead, allowing IT teams to focus on strategic initiatives.

Another significant characteristic of the FortiGate 800F is its energy efficiency. The design includes hardware optimizations that not only enhance performance but also reduce power consumption, aligning with the growing emphasis on sustainability practices.

In summary, the Fortinet FortiGate 800 and 800F series are comprehensive network security solutions that leverage advanced technologies to provide organizations with the security, performance, and flexibility necessary in today's threat landscape. With their robust threat intelligence and high throughput capabilities, these firewalls are well-suited for enterprises looking to fortify their defenses against an ever-evolving array of cyber threats.