Fortinet 800F manual Installing and configuring the cluster, Internal Network

Page 57

High availability installation

Configuring FortiGate units for HA using the CLI

 

 

Figure 13: HA network configuration

Internal Network

Port 1Port 2

 

CONSOLE

USB

 

 

10/100

 

 

10/100/1000

Esc

Enter

 

1

2

3

4

5

6

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Port 4

 

 

Hub or

 

 

 

 

Hub or

Switch

 

 

 

 

 

 

 

 

Switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Port 4

 

CONSOLE

USB

 

 

10/100

 

 

10/100/1000

Esc

Enter

 

1

2

3

4

5

6

A

 

 

 

 

 

 

 

 

Router

Port 1 Port 2

Internet

2Power on all the FortiGate units in the cluster.

As the units start, they negotiate to choose the primary cluster unit and the subordinate units. This negotiation occurs with no user intervention and normally just takes a few seconds.

Installing and configuring the cluster

When negotiation is complete the you can configure the cluster as if it was a single

FortiGate unit.

If you are installing a NAT/Route mode cluster, use the information in “NAT/Route mode installation” on page 27 to install the cluster on your network

If you are installing a Transparent mode cluster, use the information in “Transparent mode installation” on page 41 to install the cluster on your network.

FortiGate-800/800F Installation Guide

01-28006-0024-20041026

57

Image 57
Contents October 01-28006-0024-20041026 Installation GuideRegulatory Compliance TrademarksTable of Contents Index Introduction Secure installation, configuration, and managementWeb-based manager Command line interfaceDocument conventions Setup wizardFortiGate documentation FortiGate Installation GuideFortiManager documentation Related documentationFortiClient documentation FortiMail documentationComments on Fortinet technical documentation FortiLog documentationCustomer service and technical support Comments on Fortinet technical documentation Getting started Package contents Mounting Turning the FortiGate unit power on and off Connecting to the web-based managerTo power off the FortiGate unit To connect to the web-based manager Connecting to the command line interface CLIWelcome To connect to the CLIFactory default NAT/Route mode network configuration Factory default FortiGate configuration settingsNetwork Settings Factory default Transparent mode network configurationFactory default protection profiles Factory default firewall configurationWeb protection profile settings NAT/Route mode Planning the FortiGate configurationTransparent mode NAT/Route mode with multiple external network connectionsConfiguration options Web-based manager and setup wizardFront control buttons and LCD Next steps Preparing to configure the FortiGate unit in NAT/Route mode NAT/Route mode installationDMZ Dhcp or PPPoE configurationUsing the web-based manager Configuring basic settingsTo configure interfaces Go to System Network Interface To configure DNS server settings Go to System Network DNS Using the front control buttons and LCDTo add a default route Go to System Router StaticConfiguring the FortiGate unit to operate in NAT/Route mode Using the command line interfaceTo add a default gateway to an interface To add/change the administrator passwordExample To configure interfacesGet system interface To configure DNS server settingsOn page 28 and on page 29 for other settings Using the setup wizardDhcp server Starting the setup wizardConnecting the FortiGate unit to the networks FortiGate-800FortiGate-800F To connect to FortiGate-800/800F user-defined interfaces To connect the FortiGate unit running in NAT/Route modeConfiguring the networks Go to System Config Time To set the date and timeTo register the FortiGate unit Go to System Maintenance Update Center To configure virus, attack, and spam definition updatesPreparing to configure Transparent mode Transparent mode installationTo change the Management IP Go to System Network Management To change the management IP address and netmask Reconnecting to the web-based managerTo add a default gateway To change to Transparent mode using the CLITo configure the management IP address End To configure the default gatewayTo start the setup wizard Connecting the FortiGate unit to your networkFortiGate-800F Internal Network Other Network To register your FortiGate unit Reconnecting to the web-based manager Configuring FortiGate units for HA operation High availability installationHigh availability configuration settings Priorities of heartbeat device and monitor prioritiesGroup ID MAC Address To change the FortiGate unit host name High availability settings ScheduleConfig system global Set hostname namestr end Configuring FortiGate units for HA using the CLITo configure the FortiGate unit for HA operation Connecting the cluster to your networksTo connect the cluster Internal Network Installing and configuring the clusterConfiguring FortiGate units for HA using the CLI CLI IndexIndex 01-28006-0024-20041026

800F, 800 specifications

Fortinet, a leader in cybersecurity solutions, has made significant strides in fortifying enterprise networks with its FortiGate 800 and 800F series. These next-generation firewalls are designed to deliver high performance and security for organizations seeking to protect their critical assets while ensuring optimal network efficiency.

The FortiGate 800 and 800F series are built on Fortinet's proprietary Security Fabric architecture, which provides a consolidated approach to security. This architecture allows organizations to leverage seamless integration across various security solutions and services, enhancing visibility and control. With a focus on scalability, these models support various deployment scenarios—from branch offices to data centers—making them versatile options for organizations of any size.

One of the standout features of the FortiGate 800 and 800F series is their robust threat intelligence capabilities. Powered by FortiGuard Labs, these firewalls provide real-time threat intelligence that enables proactive threat mitigation and incident response. This not only helps to defend against known threats but also enhances the firewall’s ability to identify emerging threats, ensuring comprehensive protection.

The series boasts impressive performance metrics. The FortiGate 800F can process up to 20 Gbps of firewall throughput and 1.5 million concurrent sessions, making it a suitable choice for high-performance environments. Additionally, the built-in SSL inspection capabilities allow organizations to decrypt and inspect encrypted traffic, which is crucial for detecting hidden threats.

The FortiGate 800 and 800F also feature advanced security technologies, including Intrusion Prevention System (IPS), antivirus, web filtering, and application control, all managed through a unified interface. This centralization simplifies management and reduces administrative overhead, allowing IT teams to focus on strategic initiatives.

Another significant characteristic of the FortiGate 800F is its energy efficiency. The design includes hardware optimizations that not only enhance performance but also reduce power consumption, aligning with the growing emphasis on sustainability practices.

In summary, the Fortinet FortiGate 800 and 800F series are comprehensive network security solutions that leverage advanced technologies to provide organizations with the security, performance, and flexibility necessary in today's threat landscape. With their robust threat intelligence and high throughput capabilities, these firewalls are well-suited for enterprises looking to fortify their defenses against an ever-evolving array of cyber threats.