Fortinet 30B manual Restoring the previous configuration, To backup configuration using the CLI

Page 46

Installing firmware from a system reboot using the CLI

FortiGate Firmware

9Type the address of the TFTP server and press Enter: The following message appears:

Enter Local Address [192.168.1.188]:

10Type an IP address the FortiGate unit can use to connect to the TFTP server. The IP address can be any IP address that is valid for the network the interface is connected to. Make sure you do not enter the IP address of another device on this network.

The following message appears:

Enter File Name [image.out]:

11Enter the firmware image filename and press Enter.

The TFTP server uploads the firmware image file to the FortiGate unit and a message similar to the following appears:

Save as Default firmware/Backup firmware/Run image without saving: [D/B/R]

12Type D.

The FortiGate unit installs the new firmware image and restarts. The installation might take a few minutes to complete.

Restoring the previous configuration

Change the internal interface address, if required. You can do this from the CLI using the following command:

config system interface edit <interface>

set ip <address_ip4mask>

set allowaccess {pinghttpssshtelnethttp}

end

After changing the interface address, you can access the FortiGate unit from the web-based manager and restore the configuration.

Backup and Restore from a USB key

Use a USB key to either backup a configuration file or restore a configuration file. You should always make sure a USB key is properly install before proceeding since the FortiGate unit must recognize that the key is installed in its USB port.

Note: You can only save VPN certificates if you encrypt the file. Make sure the configuration encryption is enabled so you can save the VPN certificates with the configuration file. An encrypted file is ineffective if selected for the USB Auto-Install feature.

To backup configuration using the CLI

1Log into the CLI.

2Enter the following command to backup the configuration files: exec backup config usb <filename>

3Enter the following command to check the configuration files are on the key: exec usb-disk list

 

FortiGate-30B FortiOS 3.0 MR6 Install Guide

46

01-30006-0459-20080505

Image 46
Contents Install G U I D E Trademarks Regulatory complianceConfiguring InstallingConents Introduction Advanced configuration FortiGate FirmwareTesting new firmware before installing Installing firmware from a system reboot using the CLIIndex Page Introduction Register your FortiGate unitAbout the FortiGate-30B About this documentDocument conventions Further ReadingTypographic conventions Fortinet Knowledge Center Comments on Fortinet technical documentationCustomer service and technical support Customer service and technical support Installing Environmental specificationsRack mount instructions GroundingMounting To power off the FortiGate unit Connecting to the networkTo power on the FortiGate unit Plugging in the FortiGateTurning off the FortiGate unit NAT vs. Transparent mode NAT modeConnecting to the web-based manager Connecting to the FortiGate unitTransparent mode To connect to the web-based managerConnecting to the CLI To connect to the CLIConfigure the interfaces Configuring NAT modeUsing the web-based manager To configure interfaces Go to System Network InterfaceConfigure a DNS server Adding a default route and gatewayTo modify the default gateway Go to Router Static Adding firewall policiesTo set an interface to use a static address Using the CLITo set an interface to use Dhcp addressing To configure DNS server settings To set an interface to use PPPoE addressingTo modify the default gateway Configuring Transparent modeTo add an outgoing traffic firewall policy Switching to Transparent mode To switch to Transparent mode Go to System StatusTo switch to Transparent mode To configure DNS server settings Verify the configuration Backing up the configurationSet the Administrator password Restoring a configurationAdditional configuration Set the time and dateConfigure FortiGuard Updating antivirus and IPS signaturesAdditional configuration Advanced configuration Protection profilesFirewall policies Firewall policiesConfiguring firewall policies Antivirus optionsAntiSpam options Web filtering Logging FortiGate Firmware Downloading firmwareUpgrading the firmware Using the web-based managerReverting to a previous version Using the USB Auto-Install Backup and Restore from a USB keyTo revert to a previous firmware version Using the CLI To upgrade the firmware using the CLIExecute restore image namestr tftpip4 To revert to a previous firmware version using the CLIInstalling firmware from a system reboot using the CLI Execute restore image namestr tftpipv4To install firmware from a system reboot Press any key to display configuration menuRestoring the previous configuration To backup configuration using the CLITo restore configuration using the CLI Additional CLI Commands for a USB keyTo configure the USB Auto-Install using the CLI Testing new firmware before installing To test the new firmware imageTesting new firmware before installing Testing new firmware before installing Index Web filtering 37 web-based manager Page Page

30B specifications

Fortinet's FortiGate 30B is a compact yet powerful security appliance designed for small to medium-sized businesses and branch offices. This next-generation firewall (NGFW) integrates various security functions, helping organizations safeguard their networks without compromising on performance or ease of use.

One of the standout features of the FortiGate 30B is its robust security capabilities. It offers firewall protection, intrusion prevention systems (IPS), antivirus, web filtering, and application control, all in one device. This consolidated approach simplifies security management, enabling companies to deploy a range of protections without the need for multiple products.

The FortiGate 30B utilizes Fortinet's proprietary FortiOS operating system, which allows for centralized management and visibility into network traffic. With features like FortiView, administrators can gain insights into application usage, user activities, and security events, helping them make informed decisions to enhance their security posture.

Performance is another critical aspect of the FortiGate 30B. Equipped with Fortinet's purpose-built security processing units (SPUs), the device is designed to handle high throughput while maintaining low latency. This ensures that businesses can operate smoothly without facing interruptions caused by security measures.

Additionally, the FortiGate 30B supports advanced technologies such as VPN (Virtual Private Network) for secure remote access and SD-WAN (Software-Defined Wide Area Network) capabilities. This combination enables organizations to optimize their network performance and enhance connectivity between branch offices or remote workers, making it an ideal solution for today's flexible work environments.

A highlight of the FortiGate 30B is its ease of deployment. With a user-friendly interface and guided setup wizards, even those with limited IT experience can configure the device quickly. The included FortiCloud service allows for easy management and monitoring, further simplifying the administrative overhead.

Scalability is yet another critical characteristic of the FortiGate 30B. As businesses grow, they can easily expand their security infrastructure by integrating additional Fortinet solutions into their network, maintaining a cohesive security strategy without disrupting operations.

In summary, the FortiGate 30B offers a comprehensive, high-performance security solution for small and medium-sized organizations. With its integrated features, advanced technologies, and user-friendly management capabilities, it empowers businesses to protect their networks effectively while ensuring optimal performance and scalability for future growth.