CyberPower Systems CPS725SL user manual Guaranteed Uninterruptible Power System, Description

Page 3

CPS725SL

Guaranteed Uninterruptible Power System

IMPORTANT SAFETY INSTRUCTIONS (SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of unit. Read this manual thoroughly before attempting to unpack, install, or oper- ate.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area, free of conductive contaminants. (Please see specifications for acceptable temperature and humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery. No user serviceable parts inside except for battery.

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is discon- nected.

CAUTION! UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into an outlet that is not grounded. If you need to de- energize this equipment, turn off and unplug the unit.

CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before servicing the battery or installing a computer component.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell prod- ucts for life support or medical applications. DO NOT use in any circumstance that would affect operation or safety of any life support equipment or with any medical applica- tions or patient care.

DO NOT USE WITH OR NEAR AQUARIUMS! To re- duce the risk of fire or electric shock, do not use with or near an aquarium. Condensation from the aquarium can cause the unit to short out.

DESCRIPTION

1.Battery/Surge Outlets

Provides three battery powered/surge outlets for con- nected equipment and insures temporary uninterrupted operation of your equipment during a power failure.

2.Full-Time Surge Protection Outlets

Provides three always on surge suppression outlets.

3.Power Switch

Can be used as a mater on/off switch for equipment connected to the battery power supplied outlets.

4.Power On Indicator

This LED is illuminated when the utility condition is normal and the UPS outlets are providing power, free of surges and spikes.

5.Electrical Wiring Fault Indicator

This LED indicator will illuminate to warn the user that a wiring problem exists, such as bad ground, miss ground or reversed wiring. If this is illuminated, user is advised to disconnect all electrical equipment from the outlet and have an electrician check to ensure the outlet is properly wired.

6.Circuit Breaker

Located on the side of the UPS, the circuit breaker serves to provide overload and fault protection. Under normal operating conditions, the circuit breaker is depressed.

7.Serial Port to PC

This port allows connection and communication from the DB-9 serial port on the computer to the UPS unit. The UPS communicates its status to the PowerPanel™ soft- ware. This interface is also compatible with the UPS service provided by Windows NT and Windows 2000.

8.Coaxial Cable Surge Protection

Connect the coaxial cable from your cable / antenna dish source to one of the surge protector’s video connectors market “IN”. With another section of coaxial cable, con- nect the surge protector’s corresponding video connector marked

9.Communication Protection Ports

Communication protection ports will protect any standard modem, fax or telephone line.

10.Outlets Designed for AC Adapters

Allows six AC power adapter blocks to be plugged into the UPS without blocking adjacent outlets.

INSPECTION

The box should contain the following:

(1) PowerPanel™ software (floppy disk); (1) serial interface cable (DB-9);

(1)telephone communication cable; (1) user manual; (1) warranty registration card;

(1)USB adapter ; (1) UPS unit.

1

Image 3
Contents Additional Installation Tips can be Found AT Table of Contents Description Guaranteed Uninterruptible Power SystemHOW to Determine the Power Requirements of Your Equipment Hardware Installation GuideOverview For Windows NT Installation GuideUSB Function Optional For Windows 95 /98 /MEFor Windows XP Home and Professional PowerPanel Setup Window See FigurePowerPanel Main Window Description See Figure Oprating InstructionPowerPanel Shutdown Window See Figure Using the Windows NT UPS ServiceUsing the Windows 2000 UPS Service If you are using PowerPanel software Testing Your UPS SystemCondition Definitions for Illuminated LED IndicatorsAdditional troubleshooting information can be found at Trouble ShootingExpected Runtime in Minutes SpecificationsExclusive Remedies Under Limited Warranty Limited Warranty and Power Control GuaranteeMaking a Power Control Guarantee Claim Making a Limited Warranty ClaimCyberPower’s Duties Exclusion of Consequential and Other Damages Page Email sales@cyberpowersystems.com