B&B Electronics EIR510-2MT-T, EIR510-2MC-T, EIR510-2SC-T manual Remove

Page 72

2.Group ID: There are three trunk groups to configure. Choose the "Group ID" and click Select .

3.LACP: If enabled, the group is an LACP static trunk group. If disabled, the group is local static trunk group. All ports support LACP dynamic trunk. If connected to a device that also supports LACP, the LACP dynamic trunk group is automatically created.

4.Work ports: A maximum of four ports can be aggregated at the same time. With LACP static trunk group, any excess ports are considered standby and can be aggregated if a work port fails. If it is local static trunk group, the number of ports must be the same as the group member ports.

5. Select the ports to add to the trunk group. Click Add button to add

the port. To remove unwanted ports, select the port and click

Remove

button.

6.When LACP is enabled, you can configure LACP Active/Passive status for each port on the State Activity page.

7.Click Apply

8.Use Delete button to delete Trunk Group. Select the Group ID and click Delete button.

64

Manual Documentation Number: EIR510-xSFP-T_0708m

 

 

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104www.bb-elec.com

 

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445www.bb-europe.com

Image 72
Contents Product Description Ten Port Managed Industrial Ethernet Switches FCC Content About Web-based Management Preparing for Web Management Tftp Restore Configuration Tftp Backup Configuration Rapid Spanning Tree Technical Specification Features IntroductionManual Documentation Number EIR510-xSFP-T0708m Package Contents Physical Dimension W x D x H Front PanelBottom View LED Indicators FaultStatus Meaning P1 through P8Ports „ RJ-45 portsRJ-45 Pin Assignments Pin Number „ Fiber Port Cabling Wiring the Power Inputs Wiring the Fault Alarm Contact 1A@24VMounting Installation DIN-Rail MountingManual Documentation Number EIR510-xSFP-T0708m Panel Mounting Hardware Installation Installation StepsNetwork Application Ring ApplicationCoupling Ring Application Dual Homing Application Connecting to the Console Port Login in the Console InterfaceDB9 Connector RJ-45 Connector CLI Management Commands Level Modes Access Prompt Exit About This Mode1 MethodCommands Set List VlanSystem Commands Set Password UsernameLow IP High IPPort Commands Set PortidFull half 101001000autoValue Enable Disable Trunk Commands Set Vlan Commands Set GroupIDTrunk-link tag TaggedVID ListSpanning Tree Commands Set ~61440Seconds Spanning-tree Hello-time secondsForward-time seconds Stp-path-costQOS Commands Set Weighted-fairstrictAutoTrueFalse TrueFalseIgmp Commands Set Port-basedcos-onlytosOnlycos-firsttos-first Mac / Filter Table Commands Set Snmp Commands SetAuthentication Password Privacy V1v2cv3v1v2cv3Community Community-stringExactPrifix Read View Name Write View Name Notify ViewView Name ExcludedIncludedPort Mirroring Commands Set 802.1x Commands SetPort ID WordsSec Disable reject accept NumberAuthorize Tftp Commands Set SystemLog, Smtp and Event Commands SetClientserverboth Account Index Email addressSystemlogSMTPBoth Link-UPLink-DownBotSntp Commands Set Start time End timeMinute Ring Commands Set No Xring No Xring masterNo Xring couplering No Xring dualhomingAbout Web-based Management Preparing for Web ManagementSystem Login IP Configuration System InformationDhcp Server System configuration Dhcp Client System Configuration Dhcp Server Port and IP BindingsTftp Update Firmware Tftp Restore Configuration Tftp Backup ConfigurationTftp Server IP Address Enter the Tftp server IP System Event Log Syslog Configuration System Event Log Smtp Configuration System Event Log Event Configuration Fault Relay Alarm Sntp Configuration Local Time Zone Conversion from UTC Time at 1200 UTCManual Documentation Number EIR510-xSFP-T0708m „ Daylight Saving Offset mins Enter the offset in minutes IP Security User Authentication Port StatisticsPort Control Aggregator setting Port TrunkRemove Aggregator Information State ActivityPort Mirroring Rate Limiting Vlan configuration Vlan configuration Port-based Vlan „ The Vlan is displayed Use 802.1Q Configuration 802.1Q VlanGroup Configuration „ Hybrid Link Both Access Link and Trunk LinkRstp System Configuration Rapid Spanning TreeRstp System Configuration interface Rstp Port Configuration Snmp Configuration System Configuration„ Community Strings Trap Configuration SNMPV3 Configuration „ Authentication Password Enter the passwordContext Table User ProfileSnmp V3 configuration interface Access Table Group TableMIBview Table QoS Configuration QoS Policy and Priority TypeQoS Configuration interface COS Configuration TOS ConfigurationPort Base Priority Igmp Configuration Message DescriptionQuery ReportRing Ring Interface 802.1X/Radius Configuration System Configuration„ Security 802.1x Per Port Configuration Misc Configuration MAC Address Table Static MAC Address„ Add the Static MAC Address MAC Filtering Factory Default All MAC AddressesSave Configuration System RebootTrouble shooting Standard ProtocolManagement RFC StandardSnmp Trap TechnologyTransfer Rate Packet filter„ SC Single mode 9/125um Optical cable Power SupplyPower Class of serviceFirmware update Relay AlarmManagement IP SecurityInstall Temperature CaseDimensions Safety