Asante Technologies 7000 user manual Components, FS7108

Page 14

Installation

Components

This section describes the front- and back-panel layouts of the FS7108 and FS7016 Switches.

The only control on the front panel is the uplink push-button switch. The only control on the rear panel is the power switch. The LED indicators are described in detail in Chapter 3.

The uplink push-button switch is connected to a single port on each Switch. In Normal position, the port associated with the uplink switch operates like any other port on the unit. When the uplink push-button is in the depressed position, the port associated with the uplink switch becomes an uplink port and eliminates the need for a crossover cable.

FS7108

The front panel of the FS7108 contains eight 10/100Mbps ports, one Gigabit Ethernet port, one uplink switch button, and LED indicators. See Figure 2-1.

 

 

 

 

 

 

 

 

 

Uplink Switch Button

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FRIENDLYNET 7108 GIGABIT SWITCH

Switched Gigabit Ethernet Port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100/10Mbps

 

 

Link/Data

 

 

 

 

 

 

 

 

 

 

 

 

Power

 

Full Duplex/Collision

 

 

 

 

 

 

 

 

 

 

 

 

 

Full/Half

TxRx

 

 

Uplink

 

 

 

 

 

 

 

 

MII

Power

Link/Data

 

 

 

 

 

 

1

2

3

4

5

6

7

8

1 2 3 4 5 6

7 8

 

 

 

 

 

 

Normal

 

 

 

 

 

 

 

 

Power

 

 

 

 

 

 

 

 

 

 

Uplink

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LEDs

 

 

 

 

 

 

 

 

 

Eight 10/100 Ports

 

 

Figure 2-1 FS7108 front panel

The back panel of the FS7108 contains a 100–240 volt AC power connector, a power switch, and an MII slot. See Figure 2-2.

Power Connector

100–240 Vac Input

On

MII Module

Off

MII Slot

Power Switch

Figure 2-2 FS7108 back panel

Page 2-2

Image 14
Contents User’s Manual Copyright Notice Trademarks Table of Contents LED Indicators Troubleshooting Specifications Technical SupportAbout This Manual Chapter Contents Document ConventionsIntroduction Introducing the FriendlyNET 7000 SeriesModel Numbering Convention Configuration OptionsFeatures Switch Acts as a Bridge Between Network Segments Switching TechnologyPerformance Features Fast Ethernet and Gigabit Ethernet Technology Introduction Installation Package ContentsComponents FS7108Gigabit SX XP Module Expansion ModulesFS7016 Base Unit Installing a Gigabit module 10/100 8-Port XP ModuleFX MII Module MII slotInstalling an MII module Mounting ConfigurationsDesktop Mounting Rack MountingCabling Requirements 11 Mounting the FS7000 in an equipment rackConnecting Network Devices Connecting a Computer to the SwitchConnecting a Hub or a Switch to the Asanté Switch Connecting a Hub with No Uplink Port to the SwitchVoltage Requirements Powering on the SwitchCascading Multiple FS7000 Switches Installation LED Indicators Power On LED Indicators MII Power LEDFull/Half Duplex LED LED Indicators for Port Connections100/10Mbps Operation LED Link/Data LED LED Indicators on Gigabit SX ModulePower LED Full Duplex/Collision LED LED Indicators Troubleshooting A-2 Specifications FS7000 Series Physical and Environmental Specifications Gigabit SX XP Module Specifications B-4 Technical Support Contacting Technical SupportC-2 Asanté TECHNOLOGIES, INC., 821 FOX LANE, SAN JOSE, CA