Asante Technologies 7000 user manual Power On LED Indicators, MII Power LED

Page 26

LED Indicators

FRIENDLYNET 7000 SERIES GIGABIT SWITCH

A1

A2

A3

A4

A5

A6

A7

A8

B1

B2

B3

B4

B5

B6

B7

B8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100/10Mbps

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Full/Half

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Link/Data

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100/10Mbps

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Full/Half

Power

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Link/Data

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

Power

100/10 Mbps

Full/Half

Link/Data

100/10 Mbps

Full/Half

Link/Data

Figure 3-2 FS7000 LEDs

Units with a Gigabit SX XP module installed have the following additional LEDs for monitoring the status of the Gigabit port:

Power

Link/Data

Full Duplex/Collision

Power On LED Indicators

After power is turned on, the LED indicators should respond as follows:

All LED indicators blink momentarily. This represents a system reset.

The Link/Data LEDs blink from slow to steady as traffic increases.

The Power LED indicator lights and remains ON. If this indicator is not lit, check to make sure that the power cord is properly connected at both ends.

MII Power LED

The green MII Power LED indicates whether an MII 100Base-FX module is connected to the Switch. Table 3-1 describes the possible status indications of the MII Power LED.

Table 3-1 MII Power LED Status Indicator

State

Status

On

100Base-FX module is connected

Off

100Base-FX module is not connected

Page 3-2

Image 26
Contents User’s Manual Copyright Notice Trademarks Table of Contents LED Indicators Troubleshooting Specifications Technical SupportAbout This Manual Chapter Contents Document ConventionsIntroduction Introducing the FriendlyNET 7000 SeriesModel Numbering Convention Configuration OptionsFeatures Switch Acts as a Bridge Between Network Segments Switching TechnologyPerformance Features Fast Ethernet and Gigabit Ethernet Technology Introduction Installation Package ContentsComponents FS7108Gigabit SX XP Module Expansion ModulesFS7016 Base Unit Installing a Gigabit module 10/100 8-Port XP ModuleFX MII Module MII slotInstalling an MII module Mounting ConfigurationsDesktop Mounting Rack MountingCabling Requirements 11 Mounting the FS7000 in an equipment rackConnecting Network Devices Connecting a Computer to the SwitchConnecting a Hub or a Switch to the Asanté Switch Connecting a Hub with No Uplink Port to the SwitchVoltage Requirements Powering on the SwitchCascading Multiple FS7000 Switches Installation LED Indicators Power On LED Indicators MII Power LEDFull/Half Duplex LED LED Indicators for Port Connections100/10Mbps Operation LED Link/Data LED LED Indicators on Gigabit SX ModulePower LED Full Duplex/Collision LED LED Indicators Troubleshooting A-2 Specifications FS7000 Series Physical and Environmental Specifications Gigabit SX XP Module Specifications B-4 Technical Support Contacting Technical SupportC-2 Asanté TECHNOLOGIES, INC., 821 FOX LANE, SAN JOSE, CA