Cisco Systems 4027668, AAC400210112234 How Do I Renew the IP Address on My PC?

Page 28

Frequently Asked Questions

3Click Advanced in the User Mode window, and then click OK.

4Click the Up/Down selector arrows located to the right of the Connect Via section of the TCP/IP window, and then click Using DHCP Server.

5Click Options in the TCP/IP window, and then click Active in the TCP/IP Options window.

Note: Make sure that the Load only when needed option is unchecked.

6Verify that the Use 802.3 option located in the upper-right corner of the TCP/IP window is unchecked. If there is a check mark in the option, uncheck the option, and then click Info in the lower-left corner.

7Is there a Hardware Address listed in this window?

If yes, click OK. To close the TCP/IP Control Panel window, click File, and then scroll down to click Close. You have completed this procedure.

If no, you must power off your Macintosh.

8With the power off, simultaneously press and hold down the Command (Apple), Option, P, and R keys on your keyboard. Keeping those keys pressed down, power on your Macintosh but do not release these keys until you hear the Apple chime at least three times, then release the keys and let the computer restart.

9When your computer fully reboots, repeat steps 1 through 7 to verify that all TCP/IP settings are correct. If your computer still does not have a Hardware Address, contact your authorized Apple dealer or Apple technical support center for further assistance.

Q.How Do I Renew the IP Address on My PC?

A.If your PC cannot access the Internet after the cable modem is online, it is

possible that your PC did not renew its IP address. Follow the appropriate instructions in this section for your operating system to renew the IP address on your PC.

Renewing the IP address on Windows 95, 98, 98SE, and ME Systems

1Click Start, and then click Run to open the Run window.

2Type winipcfg in the Open field, and click OK to execute the winipcfg command. The IP Configuration window opens.

3Click the down arrow to the right of the top field, and select the Ethernet adapter that is installed on your PC. The IP Configuration window displays the Ethernet adapter information.

4Click Release, and then click Renew. The IP Configuration window displays a new IP address.

5Click OK to close the IP Configuration window, you have completed this procedure.

 

Note: If you cannot access the Internet, contact your service provider for further

 

assistance.

28

4030802 Rev C

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Important Safety Instructions This DocumentImportant Safety Instructions Mitteilung für CATV-Techniker Aviso a los instaladores de sistemas CatvPower Source Warning Ground the Product Protect the Product from Lightning Verify the Power Source from the On/Off Power LightProtect from Exposure to Moisture and Foreign Objects Service Warnings Check Product Safety Protect the Product When Moving ItFCC Compliance United States FCC ComplianceDeclaration of Conformity Canada EMI RegulationCE Compliance CEModem/EMTA Benefits and Features Introducing the DPC3010 and EPC3010Home Networking PerformanceDesign and Function ManagementWhats in the Carton? Front Panel Description Back Panel Description What Are the System Requirements for Internet Service? Minimum System Requirements for a PCMinimum System Requirements for Macintosh System Requirements for an Ethernet ConnectionDo Not Have a High-Speed Internet Access Account How Do I Set Up My High-Speed Internet Access Account?Already Have an Existing High-Speed Internet Access Account Where Is the Best Location for My Cable Modem? Before You Begin How Do I Mount the Cable Modem on the Wall?Mounting Instructions Location and Dimensions of the Wall-Mounting Slots Wall Mounting Instructions How Do I Connect My Devices to Use the Internet? Connecting and Installing Internet DevicesTo connect devices Connecting the Cable Modem for High-Speed Data Service Connecting the Cable Modem for High-Speed Data Service Installing USB Drivers Installing USB DriverInstalling USB Drivers Installing USB Drivers on Windows XP Systems How Do I Configure TCP/IP Protocol? Frequently Asked QuestionsConfiguring TCP/IP on Windows 95, 98, 98SE, or ME Systems Configuring TCP/IP on Windows XP Systems Configuring TCP/IP on Windows 2000 SystemsConfiguring TCP/IP on Macintosh Systems How Do I Renew the IP Address on My PC? How do I arrange for installation? Renewing the IP Address on Windows NT, 2000, or XP SystemsWhat if I dont subscribe to cable TV? How does the cable modem connect to my computer?Common Troubleshooting Issues Dont understand the front panel status indicatorsCan I run more than one device on the modem? Cable modem does not register an Ethernet connectionTips for Improved Performance Check and CorrectFront Panel LED Status Indicator Functions Initial Power Up, Calibration, and RegistrationPower Online Link Normal OperationsFront Panel LED Status Indicators During Special Conditions Special ConditionsTrademarks DisclaimerDocumentation Copyright Notice Software and Firmware Use NoticeFor Information If You Have Questions

AAC400210112234, 4027668 specifications

Cisco Systems, a global leader in networking technology, has introduced a range of products designed to empower organizations with cutting-edge solutions for their networking needs. Among their extensive portfolio, the model 4027668 (often referred to by its part number AAC400210112234) stands out, showcasing an impressive array of features and characteristics that cater to modern enterprises.

One of the primary features of Cisco Systems 4027668 is its advanced security capabilities, designed to protect network infrastructures against evolving cyber threats. This model incorporates next-gen firewall technology, intrusion prevention systems (IPS), and advanced malware protection, ensuring that organizations can safeguard sensitive data and maintain compliance with industry regulations.

In terms of performance, the 4027668 is engineered to handle high bandwidth requirements with ease. It supports a multi-gigabit architecture, enabling data transmission speeds that accommodate the demands of today’s applications, including video conferencing and cloud-based services. This capability is essential for organizations looking to provide seamless connectivity and optimize user experiences.

Flexibility and scalability are also hallmark characteristics of this Cisco model. It is designed with a modular approach, allowing businesses to configure their network according to current needs while retaining the ability to expand as requirements grow. This adaptability is particularly beneficial for dynamic environments where resource demands can fluctuate.

Cisco Systems 4027668 also embraces the latest networking technologies, including support for software-defined networking (SDN) and network functions virtualization (NFV). These technologies enable more efficient utilization of resources and facilitate quicker deployment of new services, leading to reduced operational costs and increased agility.

Management and monitoring capabilities are also enhanced in this model. With Cisco's powerful network management tools, IT teams can gain visibility into network performance, troubleshoot issues promptly, and apply configurations centrally, streamlining operations and improving overall efficiency.

Furthermore, the integration of cloud-based services allows for centralized control and automation of network processes, aligning with the trend towards hybrid IT environments. This makes the 4027668 an excellent choice for organizations leveraging cloud technology for their operational needs.

In summary, Cisco Systems 4027668, with part number AAC400210112234, is a robust networking solution characterized by its advanced security features, high performance, scalability, and modern technologies, making it a strategic investment for enterprises aiming to enhance their network infrastructure.
Top Page Image Contents