DP8400 Simplified Block Diagram | National Instruments specification

TABLE IV. Check Bit Overhead for Multiple Bit Error

Detection and Single Bit Error Correction

Number of Bits	Number of	Percentage
in Memory	Check Bits	of Excess
Data Word	Required	Memory

8	5	63%

16	6	38%

24	6 (7)	25% (29%)

32	7	22%

48	7 (8)	15% (17%)

64	8	13%

Note: The number stated assumes the use of the DP8400; the number in parentheses is required by other error correction circuits.

lists the number of additional memory chips required to sup- port single bit error correction and double bit error detection as a function of the memory data word width.

This table also shows the percentage of DRAM overhead required to implement this function. Adding error correction also increases the memory access delay, since the informa- tion contained in the overhead chips must be analyzed in each read and generated in each write operation.

DP8400 16-Bit Expandable Error Correction Chip

The DP8400 expandable error checker/corrector is shown in block diagram form in Figure 8 . This circuit offers a high degree of flexibility in applications which range from 8-bit

to 80-bit data words. It is a 16-bit chip that is easily expand- able with the simple addition of more DP8400s for each 16- bit word increment.

Figures 9a, 9b and 9c demonstrate its basic operation in the write and read memory access cycles. Figure 9a shows the normal write cycle, where system data is used by the DP8400 to generate parity bits, called check bits, based on certain combinations of the data bits. This combination is defined by the DP8400’s matrix shown in Figure 10 . When- ever a ‘‘1’’ occurs in any row, the corresponding input data bit at the top of the column helps determine the parity for that check bit labeled at the end of the row. These check bits are written along with the data at the same memory address. Also, during a memory write cycle the DP8400 checks system byte parity. This is parity associated with the data bytes transmitted between the processor and the memory card. This is an optional feature that may prove very valuable in multiple board memory systems.

Sometime later a read will occur at this same memory ad- dress. The reading of memory data may be performed in two ways, as shown in Figures 9b and 9c . In the read cycle, the DP8400 uses the data read from memory and internally regenerates check bits using the same matrix. These newly generated check bits are then compared (using X-OR gates) with the check bits read from memory to detect er- rors. The result of this comparison is called a syndrome word. Any differences in the generated versus read check bits will result in at least one syndrome bit true. This indi- cates an error in either the read data or check bit field or both.

TL/F/5012 – 10

FIGURE 8. DP8400 Simplified Block Diagram

DP8400 specifications

The National Instruments DP8400 is a robust and versatile data acquisition and control platform that stands out in the landscape of advanced instrumentation solutions. Designed to meet the demands of both academic and industrial applications, the DP8400 serves as a comprehensive tool for engineers and researchers alike, facilitating data collection, processing, and analysis in real-time.

One of the key features of the DP8400 is its high-performance data acquisition capability. It supports a wide range of input types, including analog, digital, and thermocouples, allowing users to connect various sensors and devices easily. With sampling rates of up to 1 MHz and resolutions of up to 24 bits, this instrument ensures precise and reliable data capture across diverse applications.

The DP8400 also integrates advanced signal processing technologies, including built-in filtering, signal conditioning, and data preprocessing capabilities. These features enable users to refine their measurements and extract meaningful insights from raw data, reducing the need for extensive post-processing. This is particularly beneficial in complex experiments where signal noise can interfere with results.

Another notable characteristic of the DP8400 is its versatile connectivity options. Users can connect to the device using USB, Ethernet, or wireless interfaces, facilitating seamless integration into existing laboratory setups or remote monitoring configurations. The device is compatible with various software platforms, including LabVIEW and MATLAB, providing users with familiar environments for programming and data visualization.

The DP8400 also boasts robust data storage capabilities, allowing for high-speed data logging and management. With onboard memory and support for external storage devices, users can capture extensive datasets without loss of performance. This is especially useful in long-duration experiments or when conducting time-series analysis.

In terms of durability, the DP8400 is built to withstand challenging environments, featuring rugged housing and protection against dust and moisture. This makes it suitable for both laboratory and field applications, providing reliability in diverse operating conditions.

Overall, the National Instruments DP8400 represents a powerful solution for data acquisition and analysis, combining high performance, advanced features, and exceptional flexibility. Whether for educational purposes, research projects, or industrial applications, the DP8400 is an essential tool for engineers and scientists looking to streamline their data collection and enhance their analytical capabilities. With its user-friendly interface and extensive support, it empowers users to explore new frontiers in measurement science.