Citrix Systems 9.3 setup guide To remove the inner rails from the rail assembly

Page 77

Citrix NetScaler Hardware Installation and Setup Guide

Each appliance ships with a mounting rail kit that contains two rail assemblies, one for the left side and the other for the right side of the appliance, and screws to attach the rails. An assembly consists of an inner rail and a rack rail. The supplied rail kit is 28 inches long (38 inches extended). Contact your Citrix sales representative to order a 23-inch (33 inches extended) rail kit.

Note: The same rail kit is used for both square-hole and round-hole racks. See

"Installing the Rail Assembly to the Rack" for specific instructions for threaded, round- hole racks.

To mount the appliance, you must first install the rails and then install the appliance in the rack.

Perform the following tasks to mount the appliance:

wRemove the inner rails from the rail assembly.

wAttach the inner rails to the appliance.

wInstall the rack rails on the rack.

wInstall the appliance in the rack.

The appliance is shipped with rack-rail hardware. This hardware consists of two inner rails that you attach to the appliance, one on each side, and a rack-rail assembly that you attach to the rack. The following figure illustrates the steps involved in mounting the Citrix NetScaler appliance to a rack.

To remove the inner rails from the rail assembly

1.Place the rail assembly on a flat surface.

2.Slide out the inner rail toward the front of the assembly.

3.Depress the latch until the inner rail comes all the way out of the rail assembly.

4.Repeat steps 1 through 3 to remove the second inner rail.

To attach the inner rails to the appliance

1.Position the right inner rail behind the handle on the right side of the appliance.

2.Align the holes on the rail with the corresponding holes on the side of the appliance.

3.Attach the rail to the appliance with the provided screws: 4 per side for a 1U appliance and 5 per side for a 2U appliance, as shown in the following figure.

77

Page 76 Page 78
Image 77
Page 76 Page 78
Contents Citrix NetScaler Hardware Installation and Setup Guide Copyright and Trademark Notice Contents Preparing for Installation Lights Out Management Port of the NetScaler Appliance Contents Formatting Conventions Meaning Boldface Formatting Conventions for NetScaler DocumentationThis Preface To view the documentation Documentation Available on the NetScaler ApplianceConvention Meaning To provide feedback at the Knowledge Center home Getting Service and SupportNetScaler Documentation Feedback Preface Topics Introduction to the Hardware PlatformsCommon Hardware Components Booting ScreenLCD Display Startup ScreenLCD Startup Screen Out-of-Service Screen LCD Http Statistics Screen Network Traffic Statistics Screen Http Statistics Screen10.Port Information for a 10-port Appliance Ports Row abbreviation/symbol IndicatesCopper Ethernet Ports RS232 Serial PortManagement Ports 1G SFP, 10G SFP+, and XFP PortsShort Reach Fiber 1G SFP Distance Specifications Copper 1G SFP Distance Specifications1G Pluggable Media PackSingle GE Pluggable Media Long Reach Fiber 1G SFP Distance SpecificationsShort Reach Fiber 10G SFP+ Distance Specifications Short Reach XFP 10G Distance Specifications 11.Long Reach Fiber XFP 10G Distance Specifications 10.Long Reach Fiber 10G SFP+ Distance SpecificationsDescription Products LED Port-Status IndicatorsIntroduction to the Hardware Platforms Port Type LED Location LED Function LED Color LED Indicates Field Replaceable Units Power SupplyAmber Power Supply Type LED Color LED IndicatesReplacing an AC Power Supply Replacing a DC Power Supply CompactFlash Card 13.Removing the Existing DC Power SupplyReplacing a CompactFlash Card 15.Removing the Existing CompactFlash Card To replace a solid-state drive Solid-State Drive17.Removing the Existing Solid-State Drive Shutdown -p nowHard Disk Drive To install a hard disk drive19.Removing the Existing Hard Disk Drive Direct Attach Cable21.Inserting a DAC into the 10G port To install or remove a direct attach cableCitrix NetScaler 9010 Fips Hardware Platforms25.Citrix NetScaler 9010 Fips appliance, back panel Citrix NetScaler 12000-10G26.Citrix 12000-10G appliance, front panel 28.Citrix NetScaler MPX 5500, front panel Citrix NetScaler MPX29.Citrix NetScaler MPX 5500, back panel Citrix NetScaler MPX 5550 and MPX31.Citrix NetScaler MPX 5550/5650 appliance, back panel Citrix NetScaler MPX 7500 and MPX34.Citrix NetScaler MPX 7500/9500, back panel Citrix NetScaler MPX 8200, MPX 8400, MPX 8600, and MPX Introduction to the Hardware Platforms 38.Citrix NetScaler MPX 9700/10500/12500/15500, front panel Citrix NetScaler MPX 9700, MPX 10500, MPX 12500, and MPXIntroduction to the Hardware Platforms Page Introduction to the Hardware Platforms Citrix NetScaler MPX 44.Citrix NetScaler MPX 15000 appliance, front panel Citrix NetScaler MPX 47.Citrix NetScaler MPX 17000 appliance, back panel Citrix NetScaler MPX 17500, MPX 19500, and MPXCitrix NetScaler Hardware Installation and Setup Guide Citrix NetScaler MPX 17550, MPX 19550, MPX 20550, and MPX Citrix NetScaler Hardware Installation and Setup Guide Introduction to the Hardware Platforms 16.Standard Platform Summary Fips 12000-10G Summary of Hardware Specifications17.MPX Platform Summary MPX 5550/MPX MPX 7500/MPX 5650 9500 Fips 12000-10G8x10/100/1000B Ase-T copperCitrix NetScaler Hardware Installation and Setup Guide 18.MPX Platform Summary contd MPX 8200/MPX MPX 9700/MPX MPX MPX 5550/MPX MPX 7500/MPX 5650Ten network 6x1G SFP + Port model 6x10/100/100010G and Fips MPX MPX 8200/MPX MPX 9700/MPX2x10G SFP+ 6x10/100/1000 Base-T copper Ethernet model Four network 2x10G SFP+ 10G and FipsUL & TUV-C CSA MPX 22040/MPX 19.MPX Platform Summary contd MPX 17500/MPX12x1G SFP + 24x10G SFP+ modelTUV CSA MPX Introduction to the Hardware Platforms Preparing for Installation Unpacking the Appliance Rack Requirements Preparing the Site and RackSite Requirements Space requirements Electrical Safety PrecautionsAppliance Precautions Rack Precautions Installing the Hardware Platform Number of rack units Rack Mounting the ApplianceTo attach the inner rails to the appliance To remove the inner rails from the rail assemblyAttaching inner rails To install the rack rails on the rackInstalling the Rail Assembly to the Rack To install the appliance in the rackRack Mounting the Appliance Installing and Removing 1G SFP TransceiversInstalling a 1G SFP transceiver To install a 1G SFP transceiverTo remove a 1G SFP transceiver Installing and Removing XFP and 10G SFP+ TransceiversTo install an XFP/10G SFP+ transceiver Locking an XFP transceiver To remove an XFP/10G SFP+ transceiverConnecting the Ethernet Cables Connecting the CablesTo connect the console cable to a computer or terminal Connecting the Console CableConnecting the Power Cable To connect the appliance to the power source Switching on the ApplianceTo switch on the appliance 11.Power switch on back panel Initial Configuration LCD Key Functions Using the LCD KeypadTo configure initial settings by using a serial console Using the NetScaler Serial ConsoleCitrix Application Firewall Reboot ExampleCitrix NetScaler Access Gateway Using the Setup WizardTo configure initial settings by using the Setup Wizard Using Dhcp for Initial Access Prerequisites Killall dhcpd dhcpd Sample Dhcp configuration dhcpd.confTo find the Snip address from the Dhcp server To find the Snip address from the NetScaler consoleUsing Dhcp When a Configuration File is Present Accessing a NetScaler by Using SSH Keys and No Password At the shell prompt, change the directory to /nsconfig/ssh Changing the Administrative Password Example Lights Out Management Port NetScaler Appliance Configuring the LOM Port Accessing the LOM Port by using a Web BrowserTo Configure the NetScaler LOM Port To access the LOM by using a web browserAccessing the Appliance by using the Access Console Power Cycling the ApplianceTo power cycle the appliance Performing a Core DumpObtaining Health Monitoring Information Obtaining Properties of the HostUnder Options, click Console Redirection To obtain health monitoring informationTo perform power control operations Power Control Operations using the LOM PortLights Out Management Port of the NetScaler Appliance 108 To migrate a configuration To migrate a configuration

9.3 specifications

Citrix Systems 9.3 represents a significant advancement in the realm of virtualization and application delivery technologies. As a part of Citrix's suite of products, this version builds on the strengths of previous iterations while introducing innovative features designed to enhance performance, security, and user experience.

One of the standout features of Citrix Systems 9.3 is its improved application virtualization capabilities. This version allows organizations to deliver applications seamlessly to any device, regardless of the underlying operating system. Users can access their applications from a variety of endpoints, including desktops, laptops, tablets, and smartphones, creating a flexible work environment that fosters productivity.

Another key characteristic of Citrix Systems 9.3 is the integration of advanced security measures. In an age where cyber threats are ever-evolving, this version provides robust security protocols to protect sensitive data while ensuring compliance with industry regulations. Features such as multi-factor authentication and enhanced encryption protocols are essential in safeguarding information from unauthorized access.

Performance enhancements are also a crucial aspect of Citrix Systems 9.3. This iteration includes optimizations that improve application delivery speed and user experience. By leveraging cutting-edge technologies such as HDX (High Definition Experience) and intelligent WAN optimization, Citrix ensures that applications run smoothly, even in low-bandwidth scenarios. This is particularly beneficial for remote workforces who require consistent access to critical applications.

Scalability is another hallmark of Citrix Systems 9.3. Organizations can easily scale their virtual environments up or down based on demand, making it a suitable choice for enterprises of all sizes. The management tools included in this version simplify administrative tasks, allowing IT teams to manage resources efficiently and effectively.

Additionally, Citrix Systems 9.3 has made significant strides in compatibility and user experience. The focus on a unified user interface makes navigating applications intuitive, reducing the learning curve for new users. Furthermore, the platform's adaptability ensures that it can integrate with existing systems, minimizing disruption during transitions to new technologies.

In summary, Citrix Systems 9.3 is a powerful platform offering enhanced application delivery, robust security features, improved performance, and scalability. Its focus on user experience and compatibility makes it an ideal choice for organizations looking to optimize their IT environments in today's rapidly evolving digital landscape. With Citrix Systems 9.3, businesses can confidently embrace virtualization as a means to drive productivity and innovation.
Top Page Image Contents