Dell ISCSI manual Cluster, Select Advanced → Minimum

Page 44

Problem

Probable Cause

Corrective Action

 

 

 

• The system has just been

• Use the Event Viewer and

booted and services are still

look for the following events

starting.

logged by the Cluster Service:

 

Microsoft Cluster

 

Service

 

successfully formed

 

a cluster on this

 

node.

 

Or

 

Microsoft Cluster

 

Service

 

successfully joined

 

the cluster.

 

• If these events do not appear

 

in Event Viewer, see the

 

Microsoft Cluster Service

 

Administrator’s Guide for

 

instructions on setting up the

 

cluster on your system and

 

starting the Cluster Service.

The cluster network name is not responding on the network because the Internet Connection Firewall is enabled on one or more nodes.

Configure the Internet Connection Firewall to allow communications that are required by MSCS and the clustered applications or services. For more information, see the article KB883398 at support.microsoft.com.

You are prompted to configure one network instead of two during MSCS installation.

Using Microsoft Windows NT 4.0 to remotely administer a Windows Server 2003 cluster generates error messages.

The TCP/IP configuration is incorrect.

The node-to-node network and public

 

network must be assigned static IP

 

addresses on different subnets.

The private (point-to-point) network is

Ensure that all systems are powered

disconnected.

on so that the NICs in the private

 

network are available.

This is a known issue. Some

It is strongly recommended that you

resources in Windows Server 2003

use Windows XP Professional or

are not supported in Windows NT 4.0.

Windows Server 2003 for remote

 

administration of a cluster running

 

Windows Server 2003.

Unable to add a node to the cluster.

The new node cannot access the shared disks. The shared disks are enumerated by the operating system differently on the cluster nodes.

Using Windows Disk Administration ensure that the new cluster node can enumerate the cluster disks. If the disks do not appear in Disk Administration:

1.Check all cable connections.

2.Check the volumes assignments.

3.Select Advanced Minimum.

44

Image 44
Contents Hardware Installation and Troubleshooting Guide Page Contents Page Cluster Solution ConnectivityCluster Storage Cluster Hardware RequirementsCluster Nodes Network Switches Dedicated To iSCSI Cluster Storage RequirementsDell EqualLogic PS Series Storage Array Requirements NICs Dedicated To iSCSINetwork Configuration Recommendations ISCSI SAN-Attached Cluster Supported Cluster ConfigurationsOther Documents You May Need Page Power Supplies Cabling Information Mouse, Keyboard, And Monitor Cabling InformationPrivate network Cluster Cabling Information For Public And Private NetworksNetwork Connection Description Public network Method Hardware Components For Public NetworkFor Private Network Storage Arrays Cabling Information NIC TeamingCabling The Storage For Your iSCSI SAN-Attached Cluster Dual-Port Network Adapters UsageTwo-Node iSCSI SAN-Attached Cluster Cabling The Dell EqualLogic PS4110/PS6110 Storage Arrays Sixteen-Node iSCSI SAN-Attached ClusterFor more information, see the figures below Dell EqualLogic PS6110 storage system Cluster node Switch Cabling The Dell EqualLogic PS5000/PS5500 Storage Arrays Dell EqualLogic PS5000 storage system Dell EqualLogic PS6000 storage system Switch Dell EqualLogic PS6500 storage system Obtaining More Information Page Configuring a Cluster Preparing Your Systems For ClusteringHost Integration Tools Installation OverviewAdditional Information For Installing iSCSI NICs Installing The Host Integration Tools Running The Remote Setup WizardArray Configuration EqualLogic PS Series Arrays And GroupsGroup Configuration Initializing An Array And Creating a GroupInitializing An Array And Expanding a Group Member Successfully Added to GroupComputer Access To a Group Enabling Computer Access To a GroupConfiguring Multipath I/O Between a Computer And a Group Configuring Group Access dialog box, click FinishInstalling The Microsoft iSCSI Software Initiator Configuring Firewall To Allow Icmp Echo RequestsModifying The Registry Settings Configuration Overview Of Shared Storage ArraysCreating Volumes Click Volumes and Create volumeRunning The Group Manager GUI Group Manager GUI ComponentsCreating Access Control Records Advanced Storage Features Connecting Hosts To VolumesRestoring Snapshots SnapshotsCreating Snapshots Volumes Cloning VolumesRestoring Volumes Clone Volume Space Reserve dialog box is displayedReplicating Volumes ReplicationInstallation And Configuration Of a Failover Cluster Volume CollectionsCreating Volume Collections Thin ProvisioningPage Problem Probable Cause Corrective Action Support.microsoft.comCluster Select Advanced → MinimumProblem Probable Cause Select Modify Volume SettingsClick Cluster Services ServiceDo you want to proceed y/nn Cluster Information Additional NetworksPage ISCSI Configuration Worksheet