Dell FE100, FL100 manual User’s Guide

Page 30

6.During the installation, check the appropriate box to install the Cluster Service files when prompted.

NOTICE: Do not configure the Cluster Service in this step.

7.Configure the public and private networks in each node, and place each network on separate subnets with static Internet protocol (IP) addresses.

NOTE: The public network refers to the NIC used for client connections. The pri- vate network refers to the cluster interconnect that connects the cluster nodes together.

8.Update the miniport driver for the Fibre Channel HBAs in each node.

9.Install the QLogic Fibre Channel configuration software on each node and reboot.

10.Install Dell OpenManage Application Transparent Failover (ATF) on each node and reboot.

11.Install Dell OpenManage Managed Node (Data Agent) on each node.

12.Install Dell OpenManage Data Supervisor or Dell OpenManage Data Admin- istrator on node 1.

13.Reboot node 1 and shutdown all other nodes.

14.From node 1, configure the RAID level on the storage system and then reboot node 1.

15.Run Microsoft Windows 2000 Disk Management and format and assign drive letters to the Fibre Channel hard-disk drives in the shared storage system.

16.Verify disk access and functionality to all new hard-disk drives in the shared stor- age system.

17.Power off the node.

18.Repeat steps 15 through 17 on all other nodes for each shared volume. NOTE: You do not have to reformat the disks.

19.Power on node 1 and configure the Cluster Service.

20.After the Cluster Service has started on node 1, power on all other cluster nodes and then install Cluster Service on these nodes.

21.Verify the functionality of the cluster.

22.Configure the failover for each cluster node.

23.Install and setup your application programs.

24.Record the configuration of the cluster using the data sheets in Appendix B, “Cluster Data Sheets.”

2-2 User’s Guide

Image 30
Contents USER’S Guide Page Preface Warranty and Return Policy Information Other Documents You May NeedTypographical Conventions Example del drive path filename /p Contents Configuring Storage Systems Low-Level Configuration Configuring the System SoftwareCabling the Cluster Hardware Installing Cluster Management Systems Management Software Upgrading Your PowerEdge System to a Cluster ConfigurationMaintaining the Cluster SAN ComponentsIndex Figures TablesXiv Getting Started Overview of Microsoft Windows 2000 Datacenter ServerUser’s Guide SAN-Attached Cluster Configuration Shows an advanced SAN-attached cluster configurationPowerEdge Cluster FE100/FL100 Identification SAN-Attached Cluster ConfigurationActiven/Active and Activen/Passive Configurations PowerEdge Cluster FE100/FL100 ConfigurationsActiven/Active and Activen/Passive Configuration Types Advantage Failover and Failback Support+1 Failover DisadvantagesN+1 Failover Configuration for a 4-Node Cluster Multiway FailoverExample of a 4-Node Multiway Failover Configuration Cascading FailoverDisadvantage Way Migration AdvantagesExample of a 4-Node N-Way Migration Solution Failover ConfigurationsCluster Nodes Cluster StorageCluster Interconnect Connections Private Network Cluster Client Network Connections Public Network Operating System and System Management SoftwareCluster Node Requirements PowerEdge Cluster FE100/FL100 Shared Storage Requirements SAN-Attached Cluster Requirements SAN-Attached Cluster RequirementsUser’s Guide Installation Overview User’s Guide Preparing PowerEdge and PowerVault Systems for Clustering Adding Peripherals to Your ClusterConfiguring Fibre Channel HBAs on Separate PCI Buses Configuring PowerVault DPE and DAE Enclosure AddressesCabling the Cluster Hardware Cluster Cabling ComponentsFibre Channel Copper Connectors DB-9 ConnectorUsing NICs in Your Public Network Cabling Your Public NetworkCabling Your Private Network Using Giganet cLAN for the Private Network Protecting Your Cluster From Power Failure Connecting Standby Power Supplies in the PowerVault SystemCable Configuration of PowerVault 65xF Power Supplies Cabling Your Mouse, Keyboard, Monitor in a Dell RackConfiguring Storage Systems Low-Level Configuration Configuring PowerVault Shared Storage Hard-Disk DrivesConfiguring Internal Scsi Hard-Disk Drives RAID Level for the Internal Scsi Hard-Disk DrivesConfiguring the System Software Configuring the Cluster Nodes in a Windows 2000 Domain Configuring the Windows 2000 Cluster Service Configuring the Public and Private Networks Static IP AddressConfiguring the IP Addresses for the Private Network IP Addresses for the Private NetworkIP Addresses IP Addresses Updating the Host Bus Adapter Driver Dell OpenManage Storage Management Software Dell OpenManage SoftwareDell OpenManage Description Cluster Product Nodes Configuring the System Software Using the Windows 2000 Dynamic Disks and Volumes Installing and Configuring the Windows 2000 Cluster Service Verifying Cluster ReadinessCluster Resource Group Verifying Cluster Service Verifying Cluster FunctionalityVerifying Cluster Resource Availability Configuring the Data Agent for Cluster Failover Open the Agent ConfiguratorOpen the Cluster Administrator Resource Type menu, select Generic ServiceRight-clickCluster Group and select Bring Online Configuring Failover and Failback Support Failover Support Through Four-Node ClusteringModifying the Failover Sequence of the Disk Groups User’s Guide Installing Cluster Management Systems Management Software Microsoft Cluster AdministratorRunning Cluster Administrator on a Cluster Node User’s Guide Support.dell.com User’s Guide Upgrading Your PowerEdge System to a Cluster Configuration User’s Guide Maintaining the Cluster Connecting to Data Agent Using Data Administrator Identifying the Cluster NameConnecting to Data Agent Using Data Supervisor Identifying the Device Name of the Storage ProcessorDetermining the RAID Levels of the Shared Disk Volumes Open a Command Prompt windowStart the Dell OpenManage Data Agent Configurator Adding a Third NIC to a Cluster NodeCluster Nodes and Component Identification Make New Connection wizard startsChanging the IP Address of a Cluster Node Uninstalling Cluster Service Running chkdsk /f on a Quorum DiskReplacing a Cluster Node Maintaining the Cluster User’s Guide Overview of a PowerVault SAN SAN ComponentsSAN-Attached Clusters Fibre Channel Fabrics Attaching a SAN-Attached Cluster Configuration to a Network PowerEdge server Fibre Channel switch Bridge PowerVault 130T Using Dell PowerVault Fibre Channel Switches SAN Components Additional PowerEdge Cluster Maintenance Procedures Troubleshooting Table A-1. General Cluster TroubleshootingTroubleshooting Windows Table A-2. Windows 2000 TroubleshootingCluster Data Sheets Cluster Type PowerEdge Cluster FE100/FL100 Datacenter Server Cluster Data Sheets Pre-Installation SettingsConfigure Storage Subsystem Components User’s Guide Cluster Service Configuration Post-Microsoft Cluster Service Installation Windows 2000 Datacenter Server Settings Configuring the Shared Storage System Microsoft Cluster Service InstallationIndex User’s Guide SAN-attached clusters Attaching a PowerVault storage system User’s Guide
Related manuals
Manual 12 pages 2.34 Kb Manual 24 pages 52.77 Kb Manual 2 pages 8.37 Kb Manual 56 pages 60.33 Kb

FL100, FE100 specifications

The Dell FE100, FL100, FL200, and FE200 are part of Dell's lineup of advanced networking switches designed to cater to the increasing demand for efficient data handling in enterprise environments. These switches combine powerful performance with a range of features that ensure scalability, reliability, and ease of management.

The Dell FE100 is a compact yet robust switch that caters primarily to small and medium-sized businesses. It provides gigabit connectivity with multiple ports for enhanced network performance. The FE100 is equipped with layer 2 capabilities, which offer essential features such as VLAN support, port mirroring, and link aggregation, ensuring seamless data flow across the network.

In contrast, the Dell FL100 stands out with its advanced layer 3 functionality. This switch is designed for more complex enterprise environments where routing capabilities are necessary. The FL100 supports static and dynamic routing protocols, which enhance network efficiency and traffic management. Furthermore, its Quality of Service (QoS) features enable prioritization of critical applications, optimizing network resources.

Moving up the lineup, the Dell FL200 offers increased port density and enhanced performance metrics. It caters to high-traffic networks with features such as enhanced security protocols and advanced traffic management capabilities. The FL200 integrates seamlessly into larger network infrastructures and is designed to support advanced IPv6 routing, ensuring future-proofing in an evolving technological landscape.

Finally, the Dell FE200 switch is a high-performance, enterprise-grade solution suited for environments that demand maximum throughput and minimal latency. It offers dual-speed capability, supporting both 10GbE and 1GbE connections. The FE200 is characterized by its high level of robustness and redundancy features, including dual power supplies, which safeguard against potential downtime. The switch also provides comprehensive management tools, enabling network administrators to monitor and configure the network seamlessly.

In conclusion, the Dell FE100, FL100, FL200, and FE200 switches represent a versatile and powerful range of networking devices tailored to meet various business needs. With a blend of advanced features, scalability options, and exceptional performance characteristics, these switches are invaluable assets for organizations aiming to optimize their network infrastructure. Whether for small setups or large enterprises, Dell's networking solutions provide reliability and efficiency in today’s fast-paced digital landscape.