Acnodes FES7611 user manual COM Port Connector, Fanless Embedded Controller comes with, Walnut, CA

Page 17

2-4 COM Port Connector

FES7611

Fanless Embedded Controller comes with

Intel Celeron M ULV 1.0GHz Processor

2-4 COM Port Connector

COM1: COM1 Connector

COM1 is fixed as RS-232

The pin assignment is as follows:

COM2: COM2 Connector

The COM2 is selectable as RS-232/422/485.

The pin assignment is as follows:

	© Copyright 2009 Acnodes, Inc.
661 Brea Canyon Rd., Suite 3	All rights reserved. Product description and product specifications
Walnut, CA 91789	are subject to change without notice. For latest product information,
tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com	please visit Acnodes’ web site at www.acnodes.com.

Image 17

Contents FES-7611 Fanless Embedded Controller Intel Celeron M ULV Processor FES7611Fanless Embedded Controller comes with Intel Celeron M ULV 1.0GHz ProcessorACKNOWLEDGEMENTS COPYRIGHT NOTICECE NOTICE FCC NOTICEChapter 1 Introduction ContentsChapter 2 Hardware Configuration Chapter 3 Software Utilities Chapter 4 Award BIOS SetupAppendix B Technical Summary Appendix A Programming The Watchdog TimerCHAPTER IntroductionChapter 4 Award BIOS Setup Chapter 2 Hardware ConfigurationAppendix A System Assembly 1-1. ABOUT THIS MANUAL1-2 Case Illustration z BIOS 1-3. SYSTEM SPECIFICATIONz KEYBOARD/MOUSE CONNECTOR z CPUz DISPLAY z LED INDICATORz IDE INTERFACE z LAN INTERFACEz INPUT POWER REQUIREMENT 1-4. SAFETY PRECAUTIONSz SYSTEM DIMENSION z SYSTEM NET WEIGHTHardware Configuration 2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE 2-2 Component Locations JUMPERS AND CAPS 2-3. HOW TO SET THE JUMPERSFES7611 2-4 COM Port Connector 2-5. RS-232/422/485 COM2 Selection 2.8 Power LED Connector 2.6 Keyboard/ Mouse Connector2.7 Hard Disk Drive LED Connector 2.9 VGA Connector 2.10 Hard Disk Drive Connector 2.12 LAN Connector 2.11 Universal Serial Bus Connector2.13 Clear CMOS Data Selection 2.15 AT Power Connector 2.14. Power Requirement Selection2.16 Reset/ NMI Watchdog Selection 2.18 LAN LED 2.17 Sound ConnectorCHPATER Software Utilities3.1 Introduction 3.2 VGA Driver Utility 3-2-1. Installation of VGA Driver3-3-2. To update VGA BIOS for LCD Flat Panel Display 3-3. FLASH BIOS UPDATE3-3-1. System BIOS Update Select Y, and the BIOS will be renewed. When you are refreshing the BIOS, do not turn off or reset the system, or you will damage the BIOS. After you have completed all the programming, the screen displays the table below 3-4-1. Introduction 3-4. LAN DRIVER UTILITY3-5-1. Introduction 3-5-2. Installation Procedure for Windows 9x/NT/2000/XP3-5. SOUND DRIVER UTILITY 3-6-1. Introduction 3-6. INTEL CHIPSET SOFTWARE INSTALLATION UTILITY3-6-2. Installation of Utility for Windows 98SE/ME/2000/XP 3-7-1. Installation of Utility for Windows 98SE/ 2000/XP 3.7 USB2.0 Software Installation UtilityConfiguration Sequence 3.8 Watchdog Timer Configuration2 Configurate the configuration registers 1 Enter the extended function modeExample Program Award BIOS Setup 4-1. INTRODUCTION 4-2. ENTERING SETUP CMOS Setup screen 4-3. THE STANDARD CMOS FEATURESDate TimeIDE Primary Master / Slave IDE Secondary Master / Slave HALT ON VIDEOBASE MEMORY EXTENDED MEMORYCapacity HARD DISK ATTRIBUTESIntel Celeron M ULV 1.0GHz Processor 4-4. THE ADVANCED BIOS FEATURES FES7611 Advanced Chipset Features Chipset Features Setup Screen 4-5. ADVANCED CHIPSET FEATURESVIDEO BIOS CACHEABLE SYSTEM BIOS CACHEABLEDRAM TIMING BY SELECTABLE CAS LATENCY TIMEDELAYED TRANSACTION BOOT DISPLAY depend on chipsetAGP APERTURE SIZE ON-CHIP VGA4.6 INTEGRATED PERIPHERALS FES7611 All rights reserved. Product description and product specificationsCopyright 2009 Acnodes, Inc 661 Brea Canyon Rd., SuiteFES7611 SUPER IO DEVICE 7. Use IR Pins1. Onboard FDC Controller 2. Onboard Serial Port 1/2Power Management Setup Screen 4.7 POWER MANAGEMENT SETUPPOWER MANAGEMENT MODEM USE IRQRESET CONFIGURATION DATA 4.8 PNP/PCI ConfigurationPNP/PCI Configuration Setup Screen 1. IRQ-n Assigned to RESOURCE CONTROLLED BYIRQ RESOURCES 4.9 PC HEALTH STATUS PC Health Status Setup ScreenCURRENT WARNING TEMPERATURE CURRENT CPU TEMPERATURE4.10 Frequency Control Frequency Control Setup ScreenAUTO DETECT PCI CLK SPREAD SPECTRUM4-12. LOAD OPTIMIZED DEFAULTS 4-11. LOAD FAIL-SAFE DEFAULTSTO DISABLE THE PASSWORD 4-13. Set Supervisor Password/ Set User PasswordTO SET A PASSWORD 4-14. SAVE & EXIT SETUP 4-15. EXIT WITHOUT SAVING APPENDIX System AssemblyA.1 Exploded Disgram For Rack Mount Holder A.2 Exploded Diagram For System Heat Sink A.3 Exploded Diagram For 3.5” Hard Disk Drive A.4 Exploded Diagram For 2.5” Hard Disk Drive Holder A.5 Exploded Diagram For Hard Disk Drive Holder A.6 Exploded Diagram For DC to DC Power A.7 Exploded Diagram For LED Indicator A.8 Exploded Diagram For System I/O Ports A.9 Exploded Diagram For PC104 A.10 Exploded Diagram For Motherboard A.11 Exploded Diagram For Installing DDR RAM A.12 Exploded Diagram For Removing Hard Disk Drive I/O Information B.1 Block Diagram B.2 Interrupt Map B.3 RTC & CMOS RAM Map B.4 Timer & DMA Channels Map B.5 I/O Memory Map