Acnodes FES7611 Clear CMOS Data Selection, Fanless Embedded Controller comes with, Walnut, CA

Contents Intel Celeron M ULV 1.0GHz Processor FES7611FES-7611 Fanless Embedded Controller Intel Celeron M ULV Processor Fanless Embedded Controller comes withFCC NOTICE COPYRIGHT NOTICEACKNOWLEDGEMENTS CE NOTICEChapter 1 Introduction ContentsChapter 2 Hardware Configuration Chapter 3 Software Utilities Chapter 4 Award BIOS SetupAppendix B Technical Summary Appendix A Programming The Watchdog TimerCHAPTER Introduction1-1. ABOUT THIS MANUAL Chapter 2 Hardware ConfigurationChapter 4 Award BIOS Setup Appendix A System Assembly1-2 Case Illustration z CPU 1-3. SYSTEM SPECIFICATIONz BIOS z KEYBOARD/MOUSE CONNECTORz LAN INTERFACE z LED INDICATORz DISPLAY z IDE INTERFACEz SYSTEM NET WEIGHT 1-4. SAFETY PRECAUTIONSz INPUT POWER REQUIREMENT z SYSTEM DIMENSIONHardware Configuration 2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE 2-2 Component Locations JUMPERS AND CAPS 2-3. HOW TO SET THE JUMPERS661 Brea Canyon Rd., Suite 2-4 COM Port Connector 2-5. RS-232/422/485 COM2 Selection 2.8 Power LED Connector 2.6 Keyboard/ Mouse Connector2.7 Hard Disk Drive LED Connector 2.9 VGA Connector 2.10 Hard Disk Drive Connector 2.12 LAN Connector 2.11 Universal Serial Bus Connector2.13 Clear CMOS Data Selection 2.15 AT Power Connector 2.14. Power Requirement Selection2.16 Reset/ NMI Watchdog Selection 2.18 LAN LED 2.17 Sound ConnectorCHPATER Software Utilities3.1 Introduction 3.2 VGA Driver Utility 3-2-1. Installation of VGA Driver3-3-2. To update VGA BIOS for LCD Flat Panel Display 3-3. FLASH BIOS UPDATE3-3-1. System BIOS Update Select Y, and the BIOS will be renewed. When you are refreshing the BIOS, do not turn off or reset the system, or you will damage the BIOS. After you have completed all the programming, the screen displays the table below 3-4-1. Introduction 3-4. LAN DRIVER UTILITY3-5-1. Introduction 3-5-2. Installation Procedure for Windows 9x/NT/2000/XP3-5. SOUND DRIVER UTILITY 3-6-1. Introduction 3-6. INTEL CHIPSET SOFTWARE INSTALLATION UTILITY3-6-2. Installation of Utility for Windows 98SE/ME/2000/XP 3-7-1. Installation of Utility for Windows 98SE/ 2000/XP 3.7 USB2.0 Software Installation Utility1 Enter the extended function mode 3.8 Watchdog Timer ConfigurationConfiguration Sequence 2 Configurate the configuration registersExample Program Award BIOS Setup 4-1. INTRODUCTION 4-2. ENTERING SETUP Time 4-3. THE STANDARD CMOS FEATURESCMOS Setup screen DateIDE Primary Master / Slave IDE Secondary Master / Slave EXTENDED MEMORY VIDEOHALT ON BASE MEMORYCapacity HARD DISK ATTRIBUTESIntel Celeron M ULV 1.0GHz Processor 4-4. THE ADVANCED BIOS FEATURES 661 Brea Canyon Rd., Suite Advanced Chipset Features Chipset Features Setup Screen 4-5. ADVANCED CHIPSET FEATURESCAS LATENCY TIME SYSTEM BIOS CACHEABLEVIDEO BIOS CACHEABLE DRAM TIMING BY SELECTABLEON-CHIP VGA BOOT DISPLAY depend on chipsetDELAYED TRANSACTION AGP APERTURE SIZE4.6 INTEGRATED PERIPHERALS 661 Brea Canyon Rd., Suite All rights reserved. Product description and product specificationsFES7611 Copyright 2009 Acnodes, Inc661 Brea Canyon Rd., Suite 2. Onboard Serial Port 1/2 7. Use IR PinsSUPER IO DEVICE 1. Onboard FDC ControllerMODEM USE IRQ 4.7 POWER MANAGEMENT SETUPPower Management Setup Screen POWER MANAGEMENTRESET CONFIGURATION DATA 4.8 PNP/PCI ConfigurationPNP/PCI Configuration Setup Screen 1. IRQ-n Assigned to RESOURCE CONTROLLED BYIRQ RESOURCES CURRENT CPU TEMPERATURE PC Health Status Setup Screen4.9 PC HEALTH STATUS CURRENT WARNING TEMPERATURESPREAD SPECTRUM Frequency Control Setup Screen4.10 Frequency Control AUTO DETECT PCI CLK4-12. LOAD OPTIMIZED DEFAULTS 4-11. LOAD FAIL-SAFE DEFAULTSTO DISABLE THE PASSWORD 4-13. Set Supervisor Password/ Set User PasswordTO SET A PASSWORD 4-14. SAVE & EXIT SETUP 4-15. EXIT WITHOUT SAVING APPENDIX System AssemblyA.1 Exploded Disgram For Rack Mount Holder A.2 Exploded Diagram For System Heat Sink A.3 Exploded Diagram For 3.5” Hard Disk Drive A.4 Exploded Diagram For 2.5” Hard Disk Drive Holder A.5 Exploded Diagram For Hard Disk Drive Holder A.6 Exploded Diagram For DC to DC Power A.7 Exploded Diagram For LED Indicator A.8 Exploded Diagram For System I/O Ports A.9 Exploded Diagram For PC104 A.10 Exploded Diagram For Motherboard A.11 Exploded Diagram For Installing DDR RAM A.12 Exploded Diagram For Removing Hard Disk Drive I/O Information B.1 Block Diagram B.2 Interrupt Map B.3 RTC & CMOS RAM Map B.4 Timer & DMA Channels Map B.5 I/O Memory Map