Acnodes FES7611 Super Io Device, Onboard FDC Controller, Onboard Serial Port 1/2, RxD, TxD Active

Contents Fanless Embedded Controller comes with FES7611FES-7611 Fanless Embedded Controller Intel Celeron M ULV Processor Intel Celeron M ULV 1.0GHz ProcessorCE NOTICE COPYRIGHT NOTICEACKNOWLEDGEMENTS FCC NOTICEContents Chapter 2 Hardware ConfigurationChapter 1 Introduction Chapter 4 Award BIOS Setup Chapter 3 Software UtilitiesAppendix A Programming The Watchdog Timer Appendix B Technical SummaryIntroduction CHAPTERAppendix A System Assembly Chapter 2 Hardware ConfigurationChapter 4 Award BIOS Setup 1-1. ABOUT THIS MANUAL1-2 Case Illustration z KEYBOARD/MOUSE CONNECTOR 1-3. SYSTEM SPECIFICATIONz BIOS z CPUz IDE INTERFACE z LED INDICATORz DISPLAY z LAN INTERFACEz SYSTEM DIMENSION 1-4. SAFETY PRECAUTIONSz INPUT POWER REQUIREMENT z SYSTEM NET WEIGHTHardware Configuration 2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE 2-2 Component Locations 2-3. HOW TO SET THE JUMPERS JUMPERS AND CAPSCopyright 2009 Acnodes, Inc 2-4 COM Port Connector 2-5. RS-232/422/485 COM2 Selection 2.6 Keyboard/ Mouse Connector 2.7 Hard Disk Drive LED Connector2.8 Power LED Connector 2.9 VGA Connector 2.10 Hard Disk Drive Connector 2.11 Universal Serial Bus Connector 2.12 LAN Connector2.13 Clear CMOS Data Selection 2.14. Power Requirement Selection 2.15 AT Power Connector2.16 Reset/ NMI Watchdog Selection 2.17 Sound Connector 2.18 LAN LEDSoftware Utilities CHPATER3.1 Introduction 3-2-1. Installation of VGA Driver 3.2 VGA Driver Utility3-3. FLASH BIOS UPDATE 3-3-1. System BIOS Update3-3-2. To update VGA BIOS for LCD Flat Panel Display Select Y, and the BIOS will be renewed. When you are refreshing the BIOS, do not turn off or reset the system, or you will damage the BIOS. After you have completed all the programming, the screen displays the table below 3-4. LAN DRIVER UTILITY 3-4-1. Introduction3-5-2. Installation Procedure for Windows 9x/NT/2000/XP 3-5. SOUND DRIVER UTILITY3-5-1. Introduction 3-6. INTEL CHIPSET SOFTWARE INSTALLATION UTILITY 3-6-2. Installation of Utility for Windows 98SE/ME/2000/XP3-6-1. Introduction 3.7 USB2.0 Software Installation Utility 3-7-1. Installation of Utility for Windows 98SE/ 2000/XP2 Configurate the configuration registers 3.8 Watchdog Timer ConfigurationConfiguration Sequence 1 Enter the extended function modeExample Program Award BIOS Setup 4-1. INTRODUCTION 4-2. ENTERING SETUP Date 4-3. THE STANDARD CMOS FEATURESCMOS Setup screen TimeIDE Primary Master / Slave IDE Secondary Master / Slave BASE MEMORY VIDEOHALT ON EXTENDED MEMORYHARD DISK ATTRIBUTES CapacityFES7611 4-4. THE ADVANCED BIOS FEATURES Copyright 2009 Acnodes, Inc 4-5. ADVANCED CHIPSET FEATURES Advanced Chipset Features Chipset Features Setup ScreenDRAM TIMING BY SELECTABLE SYSTEM BIOS CACHEABLEVIDEO BIOS CACHEABLE CAS LATENCY TIMEAGP APERTURE SIZE BOOT DISPLAY depend on chipsetDELAYED TRANSACTION ON-CHIP VGA4.6 INTEGRATED PERIPHERALS Copyright 2009 Acnodes, Inc All rights reserved. Product description and product specificationsFES7611 661 Brea Canyon Rd., SuiteCopyright 2009 Acnodes, Inc 1. Onboard FDC Controller 7. Use IR PinsSUPER IO DEVICE 2. Onboard Serial Port 1/2POWER MANAGEMENT 4.7 POWER MANAGEMENT SETUPPower Management Setup Screen MODEM USE IRQ4.8 PNP/PCI Configuration PNP/PCI Configuration Setup ScreenRESET CONFIGURATION DATA RESOURCE CONTROLLED BY IRQ RESOURCES1. IRQ-n Assigned to CURRENT WARNING TEMPERATURE PC Health Status Setup Screen4.9 PC HEALTH STATUS CURRENT CPU TEMPERATUREAUTO DETECT PCI CLK Frequency Control Setup Screen4.10 Frequency Control SPREAD SPECTRUM4-11. LOAD FAIL-SAFE DEFAULTS 4-12. LOAD OPTIMIZED DEFAULTS4-13. Set Supervisor Password/ Set User Password TO SET A PASSWORDTO DISABLE THE PASSWORD 4-14. SAVE & EXIT SETUP 4-15. EXIT WITHOUT SAVING System Assembly APPENDIXA.1 Exploded Disgram For Rack Mount Holder A.2 Exploded Diagram For System Heat Sink A.3 Exploded Diagram For 3.5” Hard Disk Drive A.4 Exploded Diagram For 2.5” Hard Disk Drive Holder A.5 Exploded Diagram For Hard Disk Drive Holder A.6 Exploded Diagram For DC to DC Power A.7 Exploded Diagram For LED Indicator A.8 Exploded Diagram For System I/O Ports A.9 Exploded Diagram For PC104 A.10 Exploded Diagram For Motherboard A.11 Exploded Diagram For Installing DDR RAM A.12 Exploded Diagram For Removing Hard Disk Drive I/O Information B.1 Block Diagram B.2 Interrupt Map B.3 RTC & CMOS RAM Map B.4 Timer & DMA Channels Map B.5 I/O Memory Map