Oracle Audio Technologies SunDual 10GbE XFP Verifying the Hardware Installation, Ok show-nets

Page 30

7. Connect the Ethernet cables.

Verifying the Hardware Installation

After you have installed the Sun 10-Gigabit Ethernet adapter, but before you boot your system, perform the following tasks to verify the installation. Refer to the your Solaris documentation for the detailed instructions.

Note – Verification is not required if your system supports dynamic reconfiguration (DR). Verification is not supported if your system is running Solaris x86 software.

To Verify the Hardware Installation

1.Power on the system, and when the banner appears, press the Stop-A key sequence to interrupt the boot process and display the OpenBoot (ok) prompt.

2.List the network devices on your system.

ok show-nets

a)/pci@7c0/pci@0/pci@8/network@0,1

b)/pci@7c0/pci@0/pci@8/network@0

c)/pci@7c0/pci@0/pci@2/network@0,1

d)/pci@7c0/pci@0/pci@2/network@0

e)/pci@780/pci@0/pci@1/network@0,1

f)/pci@780/pci@0/pci@1/network@0

q)NO SELECTION from the above list

Checking the .properties output for each device is the surest way to identify the device. Usually /pci@7c0/pci@0/pci@8 or /pci@7c0/pci@0/pci@9 correspond to PCIe slots, so look at those devices first.

a)/pci@7c0/pci@0/pci@8/network@0,1

b)/pci@7c0/pci@0/pci@8/network@0

Note – If you do not see the device listed, check that the adapter is properly seated. If necessary, reinstall the adapter.

20 Sun Dual 10GbE XFP PCI Express Card User’s Guide • May 2010

Image 30
Contents Sun Dual 10GbE XFP PCI Express Card Please Recycle Contents Network Configuration Configuring the nxge Device Driver ParametersConfiguring the Jumbo Frames Feature Configuring Link AggregationConfiguring VLANs Specifications Diagnostic SoftwareIndex Using This Documentation Using Unix CommandsShell Prompts Related Documentation Documentation, Support, and TrainingDocumentation Feedback Sun Dual 10GbE XFP PCI Express Card User’s Guide May Product Overview ComponentsProduct Description Hardware and Software Requirements 1shows the adapterFeatures Declaration of Conformity EMCDate Sun Dual 10GbE XFP PCI Express Card User’s Guide May Installing and Setting Up the Driver To Download the Driver on a Solaris PlatformFor Sparc systems, change to the following directory Uncompress the gzipped tar fileUnpack the tar file For x86 systemsTo discover the driver packages run the pkginfo command Select the packages you want to installVerify that the nxge driver is installed on the system To remove the driver packages run the pkgrm commandDownloading and Installing the Driver on a Linux Platform Login to your system# ifconfig -a grep eth # modprobe nxge To Remove the Driver From a Linux Platform # ethtool -i eth4 driver nxge version# rpm -e nxge-1.0-1 Installing the Adapter Installing the AdapterTo Install the Adapter Installing the Adapter Sun Dual 10GbE XFP PCI Express Card User’s Guide May Installing an Optical Transceiver Install the optical transceiversTo Install an Optical Transceiver Installing the Adapter Connect the Ethernet cables Verifying the Hardware InstallationTo Verify the Hardware Installation Ok show-netsOk cd /pci@7c0/pci@0/pci@8/network@0,1 Ok .propertiesRebooting the System Ok boot -rOk device-end Network Configuration Configuring the Network Host Files# ifconfig nxge0 plumb ip-addressup # grep nxge /etc/pathtoinst# cat /etc/hosts To Set Up a 10-Gigabit Ethernet Port on a Diskless Client Edit the hosts file in the diskless client’s root directoryExport/root/client-name Network Configuration # grep client-name /etc/bootparams Find the root directory of the client systemShut down and halt the client system Proceed with the Solaris Operating System installationOk boot /pci@7c0/pci@0/pci@8/network@0 # shutdown -i0 -g0 -yTo Boot Over the Network on Solaris x86 and Linux Systems # dladm show-devRefer the boot-device-order image Press the F12 key to install the OS from the network Image pxe-mac-addrConfiguring the nxge Device Driver Parameters Nxge Hardware and Software OverviewSetting nxge Driver Parameters on a Solaris Platform Setting Parameters Using the ndd UtilityNoninteractive and Interactive Modes To Specify Parameter Values Using the ndd Utility To Specify Device Instances for the ndd UtilityTo modify a parameter value, use the -setoption Setting Parameters Using the nxge.conf File # ndd /dev/nxge1 name to get/set ?Man prtconf Locate the path names and the associated instance numbers To Set Driver Parameters Using an nxge.conf FileFollowing parameters can be set using Set the parameters for the nxge devicesSun Dual 10GbE XFP PCI Express Card User’s Guide May Configuring the nxge Device Driver Parameters Class-opt-ipv4-tcp = 100 class-opt-ipv4-udp = # reboot -r Tuning for Maximum Performance on a Solaris PlatformReboot the system Save the nxge.conf fileTo Improve Performance on an AMD CPU Based Sun Platform Set ipipsqueuefanout=1 set ipsqueuesoftring=1Set ddimsixalloclimit=1 Configuring the nxge Device Driver Parameters Setting Parameters on a Linux Platform To Set Parameters Using the ethtool UtilityConfiguring the nxge Device Driver Parameters Following are some common parameters that can be changed # ethtool -C eth4 rx-usecs # ethtool -c eth4 # ethtool -k eth4# /usr/local/bin/nxgeconfig eth4 get # /usr/local/bin/nxgeconfig eth4 get classoptipv4udpNet.ipv4.tcpsack = Tuning for Maximum Performance on a Linux Platform# /usr/local/bin/nxgeconfig eth4 set classoptipv4tcp 0xfe0 Net.core.netdevmaxbacklog =Set up the sysctl utility # sysctl -p /etc/sysctlnxge.confConfiguring the Jumbo Frames Feature Checking Jumbo Frames ConfigurationsJumbo Frames Overview To Show the Driver Statistics in a Solaris Environment # kstat nxge1 grep rdcpackets# kstat Nxge38001 To Check Layer 2 Configuration Enabling Jumbo Frames in a Solaris EnvironmentSet the maximum MTU for maximum performance Ensure that the nxge software is installed To Check Layer 3 ConfigurationTo Enable Jumbo Frames in a Linux Environment Enabling Jumbo Frames in a Linux Environment# ifconfig eth4 To Show the Driver Statistics in a Linux EnvironmentSun Dual 10GbE XFP PCI Express Card User’s Guide May Configuring Link Aggregation Overview of Link AggregationConfiguring Link Aggregation in a Solaris Environment To Configure Link Aggregation in a Solaris Environment# ifconfig aggr33 192.168.1.1/24 broadcast + up Use the dladm show-aggr-scommand to display statistics# ifconfig aggr33 plumb # dladm show-aggr -sConfigure bond0 interface Configuring Link Aggregation in a Linux EnvironmentTo Configure Bonding for Multiple nxge Interfaces Load the bonding driverConfiguring VLANs Overview of VLANs1shows an example network that uses VLANs Configuring VLANs in a Solaris Environment To Configure Static VLANs # ifconfig -a Configuring VLANs in a Linux EnvironmentTo Configure VLANs in a Linux Environment Ensure that the nxge module is loaded# ifconfig eth2.5 xxx.xxx.xx.xxx up Configure the nxge Vlan eth2 in this example# /sbin/vconfig add eth2 Insert the Vlan moduleSpecifications ConnectorsPerformance Specifications Table A-1XFP Connector CharacteristicsPhysical Characteristics Power RequirementsSun Dual 10GbE XFP PCI Express Card User’s Guide May Diagnostic Software SunVTS Diagnostic SoftwareTo Update SunVTS to Recognize the Adapter Updating SunVTS to Recognize the AdapterUsing the SunVTS netlbtest To Use the netlbtestSun Dual 10GbE XFP PCI Express Card User’s Guide May Symbols IndexSun Dual 10GbE XFP PCI Express Card User’s Guide May