Maxtor 546106, 51536H2, 52049H3, 53073H4 specifications Glossary, Accesstime

Page 59

GLOSSARY

Glossary

A

ACCESS

To obtain data from, or place data into, RAM, a register, or data storage device.

ACCESSTIME

The interval between the issuing of an access command and the instant that the target data may be read or written. Access time includes seek time, latency and controller overhead time.

ADDRESS

A number, generally binary, distinguishing a specific member of an ordered set of locations. In disk engineering, the address may consist of drives (unit address), radial positions (cylinder address), or circumferential position (sector address).

ALLOCATION

A process of assigning designated areas of the disk to particular files.

ALTERNATETRACK

A spare track used in the event that a normal track becomes damaged or is unusable.

ANALOG

A signal or system that does not use digital states to convey information. A signal may have any number of significant states (values), contrasted to digital signals which can only have two states.

ANSI

American National Standards Institute.

APPLICATIONPROGRAM

A sequence of programmed instructions that tell the computer how to perform some end-user task, such as accounting or word processing.

AREALDENSITY

Bit density (bits per inch) multiplied by track density (tracks per inch) or bits per square inch.

ASYMMETRY

A distortion of the readback signal which is shown in different intervals between the positive and negative voltage peaks.

AUXILIARYMEMORY

Memory other than main memory; generally a mass-storage subsystem containing disk drives and backup tape drives, controller(s) and buffer memory (also called peripheral memory).

AVERAGEACCESSTIME

The average time to make all possible length accesses (seeks).

AVERAGESEEKTIME

The average time to make all possible length seeks. A typical measure of performance.

B

BADBLOCK

A block that cannot store data because of a media flaw.

BIT

An abbreviation for binary digit, of which there are two (0 and 1). A bit is the basic data unit of most digital computers. A bit is usually part of a data byte or word, but bits may be used singly to control or read logic “on-off” functions. The fundamental unit information, often used loosely to refer to a circuit or magnetization state at a particular instant in time.

BIOS

Acronym for Basic Input/Output System. The firmware area of a CPU that controls operations through the system bus and to the attached cards and peripheral devices.

BPI

Acronym for bits per inch. See bit density.

BLOCK

A group of bytes handled, stored, and accessed as a logical data unit, such as an individual file record.

BUFFER

A temporary data storage area that compensates for a difference in data transfer rates and/or data processing rates between sender and receiver.

BUS

A collection of functionally parallel conductors that forms an interconnection between functional blocks in a digital device. A length of parallel conductors that forms a major interconnection route between the computer system CPU (central processing unit) and its peripheral subsystems. Depending on its design, a bus may carry data, addresses, power, and more.

BYTE

An ordered collection of bits treated as a unit. Most often, a byte is understood to consist of eight bits. One byte is necessary to define an alphanumeric character.

C

CACHE

Random access memory (RAM) used as a buffer between the CPU and the disk drive.

CAPACITY

The amount of data, usually expressed in bytes, which can be stored in a given device or portion of same.

CENTRALPROCESSINGUNIT(CPU)

The heart of the computer system that executes programmed instructions. It includes the arithmetic logic unit (ALU) for performing all math and logic operations, a control section for interpreting and executing instructions, internal memory for temporary storage of program variables and other functions.

CHANNEL

A collection of electronic circuits used in the process of writing and reading information to and from magnetic media.

CHARACTER

An ordered collection of bits representing one of a set of predefined symbols. Often the term is used interchangeably with byte, but this is inexact.

CLOSEDLOOP

A control technique that enables the positioning system to correct off-track errors in real time. The actual head position is monitored and compared to the ideal track position to determine any position error that might be occurring. This information is then used to produce a correction signal (feedback) that goes to the positioner to correct the error. (See also track following servo).

CLOSEDLOOPSERVO

A servo control technique that uses position feedback to correct off-track errors. See Track Following Servo.

CLUSTER

The smallest allocatable unit of disk storage allowed by MS-DOS; each FAT entry represents one cluster.

CONTROLLER

An electronic device for connecting one or more mass storage peripherals (rigid disk drives, tape drives, and optical disk drives) to the input/output circuits of a host computer. Controllers vary in complexity, with more sophisticated units able to buffer and schedule commands, correct data errors, and bypass media defects without host intervention.

GL – 1

Image 59
Contents Corporate Headquarters REV EC N O SEC Tion Desc Ription ATE U T I O N Before You BeginContents Handling and Installation Product SpecificationsHost Software Interface Interface CommandsAT Interface Description Glossary Service and SupportFigures Abbreviations IntroductionMaxtorCorporation ManualOrganizationConventions Product Description KeyFeaturesModel S SP T MAX LB a Apac IT Y Product FeaturesFunctional / Interface CacheManagement MajorHDAComponents CylinderLimitationJumperDescription SubsystemConfigurationJumper Location / Configuration ModelsandCapacities ProductSpecificationsDriveConfiguration PerformanceSpecificationsAram E TE R Stan D ARD ME T RIC PhysicalDimensionsmaximumEnvironmentalLimits PowerRequirementsPowerModeDefinitions EPA Energy Star ComplianceParam E TE R OP ER AT ING ON- OPE R AT ING ReliabilitySpecificationsShock and Vibration EMC/EMI SafetyRegulatoryComplianceElectro-StaticDischargeESD HandlingandInstallationHardDriveHandlingPrecautions Multi-pack Shipping Container UnpackingandInspectionRepacking PhysicalInstallationHook up Before You BeginStart up Set upPIN IGN AL InterfaceConnectorATInterfaceDescription PinDescriptionSummaryPin Description Table PIN Name Signal Name Signal Desc RiptionPIO Timing IM in G Paramet ERS ModeDMATiming Imin G Paramet ERS ModeMode Ultra DMA TimingSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst POR T EAD WR ITE HostSoftwareInterfaceTask File Registers Conten TS LBA Bits CommandRegister M M a N D N a M E M M a N D code PA R a M E T E R S U S E D SummaryControl Diagnostic Registers Reset and Interrupt Handling InterfaceCommands ReadCommands Read DMA WriteCommands Write Multiple LE VE L ModeSet/CheckCommandsVAL UE DES C RIP Tion VAL UE Omman D Timer VAL UE TIME-OUT Period PowerModeCommandsSleep Mode Or D ENT Desc Ription InitializationCommandsOr D 15- 10, as c urrently defined Initialize Drive Parameters ER ROR Code Desc Ription Seek,FormatandDiagnosticCommandsKey Register A.R.T. CommandSetSupport ServiceandSupportServicePolicy NoQuibbleServiceFrom Dial Glossary AccesstimeCorrectableerror Fetch Landingzoneorlzone Physicalsector Softerror