Maxtor ATA manual Clearance, Ventilation

Page 25

Installation

CAUTION: The PCB is very close to the mounting holes. Do not exceed the specified length for the mounting screws. The specified screw length allows full use of the mounting hole threads, while avoiding damaging or placing unwanted stress on the PCB. The QuickView Serial ATA specifies the minimum clearance between the PCB and the screws in the mounting holes. To avoid stripping the mounting hole threads, the max- imum torque applied to the screws must not exceed 8 inch- pounds. A maximum screw length of 0.25 inches may be used.

3.5.2Clearance

Clearance from the drive to any other surface (except mounting surfaces) must be a minimum of 1.25 mm (0.05 inches).See Figure 3-5.

3.5.3Ventilation

The QuickView Serial ATA hard disk drives operate without a cooling fan, provided the base casting temperature as measured where the motor is attached to the base does not exceed 131° F (60° C). Drive reliability and warranty will be limited if the drive is exposed to temperatures greater than 60° C. Figures 3-6 and 3-7 show airflow recommended for adequate cooling. Clearance from the drive to any surface above and below the drive must be a minimum of 1.25mm. Maxtor leaves the design and application of cooling and clearance for the disk drive to the user, but the drive must maintain a case temperature at or below 60° C.

3-10 Maxtor QuickView 400/500GB Serial ATA Hard Disk Drive

Page 24 Page 26
Image 25
Page 24 Page 26
Contents January 13 Part Number QuickView 400/500GB Serial ATA Product ManualPatents UL/CSA/VDE/TUV /RoHSPublication Number Part Number Before You Begin Table of Contents Sata BUS Interface and ATA Commands Introduction List of Figures List Of Tables Manual Organization AudienceATA Terminology and ConventionsReferences Product Overview General DescriptionKEY Features Product EMI/EMS Qualifications Regulatory Compliance StandardsHardware Requirements Space Requirements InstallationUnpacking Instructions 220-Pack Shipping Container Normal operation 3Gbps Limit Data Transfer Rate 1.5Gbps Hardware Options Serial ATA Interface ConnectorAdapter Board Serial ATA Bus Connector1Device plug connector pin definition Mounting ATA Bus Interface Connector J1, Section COrientation Following points should be noted5Mounting Screw Clearance and Mounting Screw Locations 6QuickView Serial ATA Mounting Dimensions Ventilation Clearance7Lengthwise Airflow Cooling Techniques in Drive Configuration Adapter Board InstallationFor Systems with AN ATA Adapter Board Operating System LimitationsTo use the Maxtor Big Drive Enabler Big Drive Enabler Software downloadInstallation Model Number and Capacity Drive ConfigurationPhysical Dimensions Performance SpecificationsMode EPA Energy Star Compliance Power Mode DefinitionsParameter Operating NON-OPERATING Environmental LimitsPSD Shock and VibrationAnnualized Return Rate Reliability SpecificationsStart/Stop Cycles Data ReliabilityCanadian Emissions Statement Safety Regulatory ComplianceIntroduction Command InterfaceMechanical Interface Electrical InterfaceCommand Feature Register Code Values Supported CommandsRead LOG Extension Identify Drive Command Content Description Capabilities Sata Bus Interface and ATA Commands Minimum PIO transfer cycle time without flow control Minor version number See Address Offset Reserved Area Boot, Incits TR272001 = release interrupt enabled General Purpose Logging feature set supported Content Description Removable Media Status Notification feature set support Security status Sata Bus Interface and ATA Commands Product Support Warranty ServicesGlossary Glossary FCI Acronym for flux changes per inch. See also BPI Kilobyte Kb a unit of measure consisting of 1,024 210 bytes Millisecond ms One thousandth of a second .001 sec Glossary Sata Acronym for Serial ATA Glossary Index

ATA specifications

Maxtor ATA drives have played a significant role in the evolution of data storage technology, particularly during the late 20th and early 21st centuries. Known for their reliability and performance, these drives became a popular choice for consumers and businesses alike.

One of the main features of Maxtor ATA (Advanced Technology Attachment) drives is their interface. The ATA standard, which later evolved into the Parallel ATA (PATA) and Serial ATA (SATA) interfaces, allowed for the easy connection of hard drives to computers. This ensured broad compatibility across various systems, making it easier for users to upgrade their storage without facing compatibility issues.

The performance of Maxtor ATA drives was also a notable characteristic. With spinning speeds typically around 5400 RPM and 7200 RPM, these drives provided competitive read and write speeds compared to their contemporaries. The utilization of larger cache memory, often up to 8 MB or more, helped improve data transfer rates, ensuring quick access to files and applications.

Maxtor also deployed various technologies to enhance the reliability and longevity of their drives. One such innovation was the use of Shock Protection technologies, which minimized the risk of data loss due to physical shocks or impacts. This was particularly important for portable storage devices, where movement and jostling are common.

The drives were also designed with data integrity in mind. Maxtor incorporated features like S.M.A.R.T (Self-Monitoring, Analysis, and Reporting Technology) to help predict drive failures by monitoring various parameters. This proactive approach greatly assisted users in taking precautions against data loss.

Capacity-wise, Maxtor ATA drives varied significantly over the years, from a few gigabytes in the early 1990s to several terabytes by the time the brand was phased out. This scalability made Maxtor products suitable for both casual users and enterprises needing to store vast amounts of data.

In conclusion, the Maxtor ATA drives represented a significant step forward in storage technology, combining reliability, performance, and innovation. Their legacy continues to influence modern storage solutions, as many of the underlying principles and technologies have persisted into the current era of data storage. Though the brand is no longer in active development, its impact remains a noteworthy chapter in the history of computing.
Top Page Image Contents