Maxtor ATA manual Glossary

Page 62

Glossary

SUBSTRATE – The material the disk platter is made of beneath the magnetic coating. Hard disks are generally made of aluminum or magnesium alloy (or glass, for optical disks) while the substrate of floppies is usually mylar.

SURFACE – The top or bottom side of the platter which is coated with the magnetic material for recording data. On some drives one surface may be reserved for positioning information.

T

THIN FILM – A type of coating, used for disk surfaces. Thin film surfaces allow more bits to be stored per disk.

TPI – Acronym for tracks per inch. The number of tracks or cylinders that are written in each inch of travel across the surface of a disk.

TRACK – One of the many concentric magnetic circle patterns written on a disk surface as a guide to where to store and read the data.

TRACK DENSITY – How closely the tracks are packed on a disk surface. The number is specified as tracks per inch (TPI).

TRACK TO TRACK SEEK TIME – The time required for the read/write heads to move to an adjacent track.

TRANSFER RATE – The rate at which the disk sends and receives data from the controller. Drive specifications usually reference a high number that is the burst mode rate for transferring data across the interface from the disk buffer to system RAM. Sustained data transfer is at a much lower rate because of system processing overhead, head switches, and seeks.

U

UNFORMATTED CAPACITY – The total number of bytes of data that could be fit onto a disk. Formatting the disk requires some of this space to record location, boundary definitions, and timing information. After formatting, user data can be stored on the remaining disk space, known as formatted capacity. The size of a Maxtor drive is expressed in formatted capacity.

V

VOICE COIL – A type of motor used to move the disk read/write head in and out to the right track. Voice-coil actuators work like loudspeakers with the force of a magnetic coil causing a proportionate movement of the head. Maxtor's actuator uses voice-coil technology, and thereby eliminates the high stress wearing parts found on stepper motor type actuators.

W

WEDGE SERVO – The position on every track that contains data used by the closed loop positioning control. This information is used to fine tune the position of the read/write heads exactly over the track center.

WINCHESTER DISKS – Hard disks that use a technology similar to an IBM model using Winchester as the code name. These disks use read/write heads that ride just above the magnetic surface, held up by the air flow created by the turning disk. When the disk stops turning, the heads land on the surface, which has a specially lubricated coating. Winchester disks must be sealed and have a filtration system since ordinary dust particles are large enough to catch between the head and the disk.

WRITE ONCE – In the context of optical disks, technologies that allow the drive to store data on a disk and read it back, but not to erase it.

G-8 Maxtor QuickView 400/500GB Serial ATA Hard Disk Drive

Image 62
Contents QuickView 400/500GB Serial ATA Product Manual January 13 Part NumberUL/CSA/VDE/TUV /RoHS PatentsPublication Number Part Number Before You Begin Table of Contents Sata BUS Interface and ATA Commands Introduction List of Figures List Of Tables Audience Manual OrganizationTerminology and Conventions ATAReferences General Description Product OverviewKEY Features Regulatory Compliance Standards Product EMI/EMS QualificationsHardware Requirements Installation Space RequirementsUnpacking Instructions 220-Pack Shipping Container Hardware Options Serial ATA Interface Connector Normal operation 3Gbps Limit Data Transfer Rate 1.5GbpsSerial ATA Bus Connector Adapter Board1Device plug connector pin definition Orientation ATA Bus Interface Connector J1, Section CMounting Following points should be noted5Mounting Screw Clearance and Mounting Screw Locations 6QuickView Serial ATA Mounting Dimensions Clearance Ventilation7Lengthwise Airflow Cooling For Systems with AN ATA Adapter Board Adapter Board InstallationTechniques in Drive Configuration Operating System LimitationsBig Drive Enabler Software download To use the Maxtor Big Drive EnablerInstallation Drive Configuration Model Number and CapacityPerformance Specifications Physical DimensionsMode Power Mode Definitions EPA Energy Star ComplianceEnvironmental Limits Parameter Operating NON-OPERATINGShock and Vibration PSDStart/Stop Cycles Reliability SpecificationsAnnualized Return Rate Data ReliabilitySafety Regulatory Compliance Canadian Emissions StatementMechanical Interface Command InterfaceIntroduction Electrical InterfaceSupported Commands Command Feature Register Code ValuesRead LOG Extension Identify Drive Command Content Description Capabilities Sata Bus Interface and ATA Commands Minimum PIO transfer cycle time without flow control Minor version number See Address Offset Reserved Area Boot, Incits TR272001 = release interrupt enabled General Purpose Logging feature set supported Content Description Removable Media Status Notification feature set support Security status Sata Bus Interface and ATA Commands Warranty Services Product SupportGlossary Glossary FCI Acronym for flux changes per inch. See also BPI Kilobyte Kb a unit of measure consisting of 1,024 210 bytes Millisecond ms One thousandth of a second .001 sec Glossary Sata Acronym for Serial ATA Glossary Index

ATA specifications

Maxtor ATA drives have played a significant role in the evolution of data storage technology, particularly during the late 20th and early 21st centuries. Known for their reliability and performance, these drives became a popular choice for consumers and businesses alike.

One of the main features of Maxtor ATA (Advanced Technology Attachment) drives is their interface. The ATA standard, which later evolved into the Parallel ATA (PATA) and Serial ATA (SATA) interfaces, allowed for the easy connection of hard drives to computers. This ensured broad compatibility across various systems, making it easier for users to upgrade their storage without facing compatibility issues.

The performance of Maxtor ATA drives was also a notable characteristic. With spinning speeds typically around 5400 RPM and 7200 RPM, these drives provided competitive read and write speeds compared to their contemporaries. The utilization of larger cache memory, often up to 8 MB or more, helped improve data transfer rates, ensuring quick access to files and applications.

Maxtor also deployed various technologies to enhance the reliability and longevity of their drives. One such innovation was the use of Shock Protection technologies, which minimized the risk of data loss due to physical shocks or impacts. This was particularly important for portable storage devices, where movement and jostling are common.

The drives were also designed with data integrity in mind. Maxtor incorporated features like S.M.A.R.T (Self-Monitoring, Analysis, and Reporting Technology) to help predict drive failures by monitoring various parameters. This proactive approach greatly assisted users in taking precautions against data loss.

Capacity-wise, Maxtor ATA drives varied significantly over the years, from a few gigabytes in the early 1990s to several terabytes by the time the brand was phased out. This scalability made Maxtor products suitable for both casual users and enterprises needing to store vast amounts of data.

In conclusion, the Maxtor ATA drives represented a significant step forward in storage technology, combining reliability, performance, and innovation. Their legacy continues to influence modern storage solutions, as many of the underlying principles and technologies have persisted into the current era of data storage. Though the brand is no longer in active development, its impact remains a noteworthy chapter in the history of computing.