Maxtor 96147H6, 98196H8 specifications PowerModeCommands, Timer VAL UE TIME-OUT Period

Page 49

INTERFACE COMMANDS

PowerModeCommands

Standby Immediate – 94h/E0h

Spin down and do not change time out value. This command will spin the drive down and cause the drive to enter the STANDBY MODE immediately. If the drive is already spun down, the spin down sequence is not executed.

Idle Immediate – 95h/E1h

Spin up and do not change time out value. This command will spin up the spin motor if the drive is spun down, and cause the drive to enter the IDLE MODE immediately. If the drive is already spinning, the spin up sequence is not executed. The actuator is parked and some circuits are powered off.

Standby – 96h/E2h

Spin down and change time out value. This command will spin the drive down and cause the drive to enter the STANDBY MODE immediately. If the drive is already spun down, the spin down sequence is not executed. A non-zero value placed in the sector count register will enable the Automatic Power Down sequence. The timer will begin counting down when the drive returns to the IDLE MODE. A value of zero placed in the sector count register will disable the Automatic Power Down sequence.

Idle – 97h/E3h

Spin up and change time out value. This command will spin-up the spin motor if the drive is spun-down.

If the drive is already spinning, the spin up sequence is not executed. A non-zero value placed in the Sector Count register will enable the Automatic Power Down sequence and their timer will begin counting down immediately. A value of zero placed in the Sector Count register will disable the Automatic Power Down sequence. The actuator is parked and some circuits are powered off.

TIMER VAL UE

TIME-OUT PERIOD

 

 

0

Time-out disabled

 

 

1 - 240

(value * 5) seconds

241 - 251

((value - 240) * 30) minutes

252

21 minutes

253

Vendor unique period = 10 hours

254

Reserved

255

21 m inutes, 15 seconds

Check Power Mode – 98h/E5h

This command returns a code in the Sector Count register that determines the current Power Mode status of the drive. If the drive is in, going to, or recovering from the STANDBY MODE the drive sets the Sector Count register to OOh. If the drive is in the IDLE MODE or ACTIVE MODE, the drive sets the Sector Count register to FFh.

Set Sleep Mode – 99h/E6h

This command will spin the drive down and cause the drive to enter the SLEEP MODE immediately. If the drive is already spun down, the spin down sequence is not executed.

Note: The only way to recover from SLEEP MODE is with a software reset or a hardware reset.

7 – 8

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Hard Disk Drive Specifications Models 98196H8 and 96147H6 Revisions U T I O N Before You BeginContents Handling and Installation Product SpecificationsAT Interface Description Interface CommandsHost Software Interface Glossary Service and SupportFigures MaxtorCorporation IntroductionManualOrganization AbbreviationsConventions Product Description KeyFeaturesFunctional / Interface Product FeaturesMOD ELS CYL SPT MAX L BA Apac IT Y CacheManagement MajorHDAComponents Jumper Location / Configuration SubsystemConfigurationCylinderLimitationJumperDescription DriveConfiguration ProductSpecificationsPerformanceSpecifications ModelsandCapacitiesAram E TE R Stan D ARD ME T RIC PhysicalDimensionsmaximumPowerModeDefinitions PowerRequirementsEPA Energy Star Compliance EnvironmentalLimitsShock and Vibration ReliabilitySpecificationsParam E TE R OP ER AT ING ON- OPE R AT ING EMC/EMI SafetyRegulatoryComplianceHardDriveHandlingPrecautions HandlingandInstallationElectro-StaticDischargeESD Multi-pack Shipping Container UnpackingandInspectionRepacking PhysicalInstallationHook up Before You BeginStart up Set upATInterfaceDescription InterfaceConnectorPinDescriptionSummary PIN IGN ALPin Description Table PIN Name Signal Name Signal Desc RiptionPIO Timing IM in G Paramet ERS ModeDMATiming Imin G Paramet ERS ModeMode Ultra DMA TimingSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Task File Registers HostSoftwareInterfacePOR T EAD WR ITE Conten TS LBA Bits CommandRegister M M a N D N a M E M M a N D code PA R a M E T E R S U S E D SummaryControl Diagnostic Registers Reset and Interrupt Handling InterfaceCommands ReadCommands Read DMA WriteCommands Write Multiple VAL UE DES C RIP Tion ModeSet/CheckCommandsLE VE L VAL UE Omman D Timer VAL UE TIME-OUT Period PowerModeCommandsSleep Mode Or D ENT Desc Ription InitializationCommandsOr D 15- 10, as c urrently defined Initialize Drive Parameters ER ROR Code Desc Ription Seek,FormatandDiagnosticCommandsKey Register A.R.T. CommandSetServicePolicy ServiceandSupportNoQuibbleService SupportFrom Dial Glossary AccesstimeCorrectableerror Fetch Landingzoneorlzone Physicalsector Softerror

96147H6, 98196H8 specifications

The Maxtor 98196H8 and 96147H6 are notable hard drive models that were part of Maxtor's diverse range of storage solutions. Both models were designed to cater to various computing needs and display characteristics that made them reliable, high-performance options during their time in the market.

The Maxtor 98196H8 is a 19.1 GB hard drive that utilizes the IDE interface, which is known for its ease of use and compatibility with a broad range of motherboards. This model features a rotational speed of 5400 RPM, striking a balance between performance and power consumption. With a data transfer rate of up to 33 MB/s, the 98196H8 is capable of efficiently handling average workloads, making it suitable for everyday computing tasks such as word processing, web browsing, and media playback.

One standout characteristic of the 98196H8 is its shock protection technology, which enhances durability and reduces the risk of data loss from accidental drops. The drive uses fluid dynamic bearing (FDB) motors for quieter operation and increased reliability. Additionally, Maxtor's proprietary technology, including the SoftSonic feature, allows for reduced operational noise levels, making it an appealing choice for users who prioritize a quiet working environment.

On the other hand, the Maxtor 96147H6 boasts a slightly larger capacity of 14.7 GB and shares similar interface traits and rotational speed as the 98196H8. With a focus on providing reliable storage for desktop applications, this model leverages Maxtor's advanced data recovery solutions, which help ensure that users can restore lost data in the event of drive failures. Its high-capacity storage makes it well-suited for users dealing with larger files or needing additional space for various applications and media.

Both models are equipped with Maxtor's Error Recovery Control technology, which actively manages potential read/write errors, ensuring data integrity during storage and retrieval processes. This is especially beneficial for users handling critical information or relying on the storage for important projects.

In conclusion, the Maxtor 98196H8 and 96147H6 hard drives exemplified Maxtor's dedication to creating dependable storage solutions for consumers. With their variety of capacities, advanced technologies, and characteristics tailored to improve reliability and performance, they served many users well during their availability in the market.
Top Page Image Contents