Maxtor 98196H8, 96147H6 specifications Before You Begin, Hook up

Page 24

INSTALLATION

Before You Begin

Important – Please Read

Please read this installation section completely before installing the Maxtor hard drive. It gives general information for installing a Maxtor hard drive in a typical computer system. If you don’t understand the installation steps, have a qualified computer technician install the hard drive.

Back up. Protect your Existing Data

Periodic backup of important data is always a good idea. Whenever your computer is on, there is the potential for losing data on your hard drive. This is especially true when running disk utilities or any software that directly manipulates your files. Maxtor recommends that you make a backup copy of the files on any existing hard drives prior to installing the new drive. If required, this data may then be copied to the Maxtor hard drive after it has been installed in the computer. Refer to your computer user’s manual for detailed data backup instructions.

Tools for Installation

The following tools are needed to install your new Maxtor hard drive:

•A small (#2) Phillips head screw driver

•Small needle-nose pliers or tweezers

•Your computer user’s manuals

•Operating system software

System Requirements

•IDE/AT interface Maxtor recommends:

•Drives less than or equal to 8.4 GB – 486 DX 66 MHz

•Drives larger than 8.4 GB – Pentium-class processor

Operating System Requirements

•Drives less than or equal to 8.4 GB:

-DOS 5.0 or higher

•Drives larger than 8.4 GB:

-Installing as boot drive (Primary Master) requires full installation set of Windows 95/98 – not an update from DOS or Windows 3.x.

-Installing as non-boot drive (Primary Slave, Secondary Master or Slave) requires Windows 95/98 on the boot drive.

Hook up

Maxtor recommends that you use the MaxBlast™ Plus software to create a customized installation guide for your system before physically installing your new hard drive. The information created by MaxBlast Plus relates to the following illustrations.

Boot the System with the MaxBlast Plus Diskette

Before physically installing the Maxtor hard drive, boot your system with the MaxBlast Plus diskette. It will assist you with the instructions in this section for a successful installation.

Configure the Drive Jumpers

The jumper configurations have three valid jumper settings – Master, Slave and Cable Select. Maxtor hard drives are always shipped with the Master jumper setting enabled.

Install the 5.25-inch Mounting Brackets

If the Maxtor hard drive will be mounted in a 5.25-inch device bay, you will need to attach 5.25-inch brackets to the hard drive. These brackets are not required if the drive is mounted in a 3.5-inch device bay.

4 – 4

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Hard Disk Drive Specifications Models 98196H8 and 96147H6 Revisions Before You Begin U T I O NContents Product Specifications Handling and InstallationInterface Commands AT Interface DescriptionHost Software Interface Service and Support GlossaryFigures Introduction MaxtorCorporationManualOrganization AbbreviationsConventions KeyFeatures Product DescriptionProduct Features Functional / InterfaceMOD ELS CYL SPT MAX L BA Apac IT Y CacheManagement MajorHDAComponents SubsystemConfiguration Jumper Location / ConfigurationCylinderLimitationJumperDescription ProductSpecifications DriveConfigurationPerformanceSpecifications ModelsandCapacitiesPhysicalDimensionsmaximum Aram E TE R Stan D ARD ME T RICPowerRequirements PowerModeDefinitionsEPA Energy Star Compliance EnvironmentalLimitsReliabilitySpecifications Shock and VibrationParam E TE R OP ER AT ING ON- OPE R AT ING SafetyRegulatoryCompliance EMC/EMIHandlingandInstallation HardDriveHandlingPrecautionsElectro-StaticDischargeESD UnpackingandInspection Multi-pack Shipping ContainerPhysicalInstallation RepackingBefore You Begin Hook upSet up Start upInterfaceConnector ATInterfaceDescriptionPinDescriptionSummary PIN IGN ALPIN Name Signal Name Signal Desc Ription Pin Description TableIM in G Paramet ERS Mode PIO TimingImin G Paramet ERS Mode DMATimingUltra DMA Timing ModeSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst HostSoftwareInterface Task File RegistersPOR T EAD WR ITE Conten TS LBA Bits CommandRegister Summary M M a N D N a M E M M a N D code PA R a M E T E R S U S E DControl Diagnostic Registers Reset and Interrupt Handling InterfaceCommands ReadCommands Read DMA WriteCommands Write Multiple ModeSet/CheckCommands VAL UE DES C RIP TionLE VE L VAL UE Omman D PowerModeCommands Timer VAL UE TIME-OUT PeriodSleep Mode InitializationCommands Or D ENT Desc RiptionOr D 15- 10, as c urrently defined Initialize Drive Parameters Seek,FormatandDiagnosticCommands ER ROR Code Desc RiptionA.R.T. CommandSet Key RegisterServiceandSupport ServicePolicyNoQuibbleService SupportFrom Dial Accesstime GlossaryCorrectableerror Fetch Landingzoneorlzone Physicalsector Softerror

96147H6, 98196H8 specifications

The Maxtor 98196H8 and 96147H6 are notable hard drive models that were part of Maxtor's diverse range of storage solutions. Both models were designed to cater to various computing needs and display characteristics that made them reliable, high-performance options during their time in the market.

The Maxtor 98196H8 is a 19.1 GB hard drive that utilizes the IDE interface, which is known for its ease of use and compatibility with a broad range of motherboards. This model features a rotational speed of 5400 RPM, striking a balance between performance and power consumption. With a data transfer rate of up to 33 MB/s, the 98196H8 is capable of efficiently handling average workloads, making it suitable for everyday computing tasks such as word processing, web browsing, and media playback.

One standout characteristic of the 98196H8 is its shock protection technology, which enhances durability and reduces the risk of data loss from accidental drops. The drive uses fluid dynamic bearing (FDB) motors for quieter operation and increased reliability. Additionally, Maxtor's proprietary technology, including the SoftSonic feature, allows for reduced operational noise levels, making it an appealing choice for users who prioritize a quiet working environment.

On the other hand, the Maxtor 96147H6 boasts a slightly larger capacity of 14.7 GB and shares similar interface traits and rotational speed as the 98196H8. With a focus on providing reliable storage for desktop applications, this model leverages Maxtor's advanced data recovery solutions, which help ensure that users can restore lost data in the event of drive failures. Its high-capacity storage makes it well-suited for users dealing with larger files or needing additional space for various applications and media.

Both models are equipped with Maxtor's Error Recovery Control technology, which actively manages potential read/write errors, ensuring data integrity during storage and retrieval processes. This is especially beneficial for users handling critical information or relying on the storage for important projects.

In conclusion, the Maxtor 98196H8 and 96147H6 hard drives exemplified Maxtor's dedication to creating dependable storage solutions for consumers. With their variety of capacities, advanced technologies, and characteristics tailored to improve reliability and performance, they served many users well during their availability in the market.
Top Page Image Contents