Maxtor VL 17 manual Figures

Page 9

		DIAMONDMAX VL 17 PRODUCT MANUAL
Figures
Figure	Title	Page
2 - 1	PCBA Jumper Location and Configuration	2 - 6
3 - 1	Outline and Mounting Dimensions	3 - 2
4 - 1	Multi-pack Shipping Container	4 - 2
4 - 2	Single-pack Shipping Container (Option A)	4 - 3
4 - 3	Single-pack Shipping Container (Option B)	4 - 3
4 - 4	Master, Slave and Cable Select Settings	4	- 5
4 - 5	5.25-inch Mounting Brackets and Rails	4 - 6
4 - 6	IDE Interface and Power Cabling Detail	4 - 7
4 - 7	Master, Slave and Cable Select Settings	4 - 10
5 - 1	Data Connector	5 - 1
5 - 2	PIO Data Transfer to/from Device	5 - 3
5 - 3	Multi-word DMA Data Transfer	5 - 4
5 - 4	Initiating an Ultra DMA Data In Burst	5 - 5
5 - 5	Sustained Ultra DMA Data In Burst	5 - 6
5 - 6	Host Pausing an Ultra DMA Data In Burst	5 - 6
5 - 7	Device Terminating an Ultra DMA Data In Burst	5 - 7
5 - 8	Host Terminating an Ultra DMA Data In Burst	5 - 7
5 - 9	Initiating an Ultra DMA Data Out Burst	5 - 8
5 - 10	Sustained Ultra DMA Data Out Burst	5 - 8
5 - 11	Device Pausing an Ultra DMA Data Out Burst	5 - 9
5 - 12	Host Terminating an Ultra DMA Data Out Burst	5 - 9
5 - 13	Device Terminating an Ultra DMA Data Out Burst	5 - 10

v

Image 9

Contents HA RD Drive Produc T MA Nual DiamondMaxVL REV EC no Section Description Date U T I O N Before You BeginContents Handling and Installation Product SpecificationsHost Software Interface AT Interface DescriptionInterface Commands Service and SupportGlossary Figures Maxtor Corporation IntroductionManual Organization AbbreviationsConventions Signal ConventionsKey Words NumberingProduct Description DiamondMax VL 17 Key FeaturesFunctional / Interface Product FeaturesOn-the-Fly Hardware Error Correction Code ECC Logical Block AddressingDefect Management Zone DMZ Cache Management Major HDA Components Jumper Location/Configuration Subsystem ConfigurationCylinder Limitation Dual Drive SupportDrive Configuration Product SpecificationsPerformance Specifications Models and CapacitiesParameter Standard Metric Physical DimensionsPower Mode Definitions Power RequirementsEPA Energy Star Compliance Environmental LimitsShock and Vibration Reliability SpecificationsSafety Regulatory Compliance Radiated Electromagnetic Field Emissions EMC ComplianceCanadian Emissions Statement Hard Drive Handling Precautions Handling and InstallationPre-formatted Drive Important NoticeMulti-pack Shipping Container Unpacking and InspectionPhysical Installation Recommended Mounting ConfigurationRepacking Tools for Installation Handling PrecautionsSystem Requirements Drive Identification InformationHard Drive Identification General RequirementsInstalling 5.25-inch Mounting Brackets and Rails Systems Using Cable SelectInstalling in a Device Bay Mounting Drive in SystemAttaching System Cables Attaching Interface and Power CablesSystem Setup Setting the Bios CmosBios Cmos Parameters Hard Drive Preparation System Hangs During Boot PIN Signal Interface ConnectorAT Interface Description Pin Description SummaryPin Description Table PIN Name Signal Name Signal DescriptionPIO Timing Timing Parameters ModeDMA Timing Ultra DMA Timing Mode MIN MAXSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Features Register Error RegisterHost Software Interface Task File RegistersSector Number Register Sector Count RegisterCylinder Number Registers Device/Head RegisterCommand Register Command Name Command Code Parameters Used Timer Value TIME-OUT PeriodSummary Alternate Status Register Control Diagnostic RegistersDevice Control Register Digital Input RegisterReset and Interrupt Handling Reset HandlingInterrupt Handling Set Feature Commands Interface CommandsRead Commands Read SectorsRead Verify Sectors Read Multiple Read DMASet Multiple Mode Write CommandsWrite Sectors Write Verify SectorsWrite DMA Write MultipleSet Feature Commands Set Features ModeValue Description Power Mode Commands Sleep Mode Initialization Commands Word Content DescriptionIdentify Drive 15-8 = PIO data transfer mode = Write Cache enabled Initialize Drive Parameters Execute Drive Diagnostic Seek, Format and Diagnostic CommandsError Code Description Format TrackExecute S.M.A.R.T A.R.T. Command SetService Policy Service and SupportNo Quibble Service SupportMaxFax Service Customer ServiceInternet Glossary Access TimeCylinder Zero Gigabyte GB Logical Block Addressing Read Gate Signal THIN-FILM Media