Appendix C. Driver Error Messages
Message |
|
| Notes and Corrective Action | ||
Set370:#1 FYI. Use | an | This message is provided for information and may be ignored. Read | |||
Array | called | <%s> | to | Appendix C.1 for more information. | |
expose diagnostic info. |
|
| |||
|
|
|
| This message is provided for information and may be ignored. The | |
Set370:#2a. | FYI. | MD | message is printed when the Map Descriptor length in the | ||
Length=%d assigned by | configuration file has not been specified. The driver makes the | ||||
driver. |
|
|
| correction by itself. To stop this message being printed, modify the | |
|
|
|
| configuration file to match the length reported in the message. | |
Set370:#3 Err. No Write | This Driver cannot be used to write to the Setra device. Remove | ||||
MD's allowed. |
| any Map Descriptors whose function requires the FieldServer to | |||
| write to the Setra device. 3 | ||||
Set370:#4 | FYI. | MD | This message is provided for information and may be ignored. The | ||
address parameter is ignored by the driver. To stop this message | |||||
param=Address has | no | being printed, remove the address parameter from the configuration | |||
meaning. Ignoring. |
| file. |
| ||
|
|
|
|
| |
|
|
|
| There are a few variations of this message. Note the variation and | |
Set370:#5 |
| Err. | report the error to FieldServer tech support. You cannot resolve this | ||
Diagnostic x |
|
| error yourself. The error is printed when the driver executes a | ||
|
|
|
| diagnostic function used for QA testing. | |
Set370:#6 Err. Array too | The Data Array associated with the reported MD is too short to store | ||||
short. DA=%s MD=%s | all the data returned by the Setra Gage. Increase the length of the | ||||
Data Array and of the Map Descriptor.3 | |||||
|
|
|
| The response to a pressure reading request cannot be parsed by the | |
Set370:#7 Err. Pressure | driver. | Use the connection view to check the number of protocol | |||
message | can’t | be | errors. | If they keep rising, then take a log and report the error to | |
parsed. Abandoned! |
| FieldServer Tech Support. If the protocol errors are occasional then | |||
|
|
|
| ignore them.4 | |
|
|
|
| The response to a status reading request cannot be parsed by the | |
Set370:#8* Err. Status | driver. | Use the connection view to check the number of protocol | |||
message | can’t | be | errors. If they keep rising, then take a log and report the error to | ||
parsed. Abandoned! |
| FieldServer Tech Support. If the protocol errors are occasional then | |||
|
|
|
| ignore them. | |
|
|
|
| A Map Descriptor is found which does not have the ‘Gage_Function” | |
Set370:#9 FYI. Default | specified. The driver assumes your intention was to read the Gage’s | ||||
to reading pressure. |
| pressure. If you wish stop this message being printed then modify | |||
|
|
|
| the configuration file and specify the ‘Gage_Function’ = ‘Pressure’.3 | |
Set370:#10 Err. DA=%s | This message is printed when the driver is configured as a Server. | ||||
The Data Array associated with the reported MD is too short to store | |||||
too | short. | Act=%d | the message. Modify the MD length and the DA length and try | ||
Rqd=%d MD=%s |
| again.3 |
| ||
3 Modify the configuration CSV file. Download the modified file to the FieldServer and reset the FieldServer for the changes to take effect.
4Message is printed once and then suppressed. This is to prevent the error log filling with redundant repetition and thus obscuring other important information.
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com Tel: (408)