Abit NF7-S2 Swap Floppy Drive, Boot Up Floppy Seek, Boot Up NumLock Status, Security Option

Page 45

BIOS Setup

3-11

 

 

sequence of the drive selected. Set [Boot Other Device] to [Enabled] if you wish to boot from another device other than these three items.

Swap Floppy Drive:

This item can be set as Disabled or Enabled. The default setting is Disabled. When this feature is enabled, you don’t need to open the computer case to swap the position of floppy disk drive connectors. Drive A can be set as drive B and drive B can be set as drive A.

Boot Up Floppy Seek:

When the computer boots up, the BIOS detects if the system has a FDD or not. When this item is set to Disabled, if the BIOS detects no floppy drive, it will display a floppy disk drive error message. If this item is disabled, the BIOS will skip this test. The default setting is Disabled.

Boot Up NumLock Status:

This item determines the default state of the numeric keypad at system booting up.

[On]: The numeric keypad functions as number keys.

[Off]: The numeric keypad functions as arrow keys.

Security Option:

This item determines when the system will prompt for password - every time the system boots or only when enters the BIOS setup.

[Setup]: The password is required only when accessing the BIOS Setup.

[System]: The password is required each time the computer boots up.

To disable security, select Set Supervisor Password at main menu and then you will be asked to enter the password. Do not type anything and just press the <Enter> key and it will disable security. Once security is disabled, the system will boot and you can enter the BIOS setup menu freely.

NOTE: Don’t forget your password. If you forget the password, you will have to open the computer case and clear all information in the CMOS before you can start up the system. But by doing this, you will have to reset all previously set options.

APIC Mode:

Leave this item to its default setting.

MPS Version Ctrl For OS:

This item specifies which version of MPS (Multi-Processor Specification) this motherboard will use. The options are 1.1 and 1.4. The default setting is 1.4. If you use an older OS for dual processor executing, please set this option to 1.1.

OS Select For DRAM > 64MB:

This item allows you to access the memory that is over 64MB in OS/2. Leave this item to its default [Non-OS2] setting for operating system other than OS/2.

User’s Manual

Page 44 Page 46
Image 45
Page 44 Page 46
Contents NF7 Series Copyright and Warranty Notice Table of Contents Appendix a Introduction Features & SpecificationsIeee 1394 NF7-S NF7-M Model Chipset Features NF7-SNF7-S2 NF7-S2GLayout Diagram NF7/NF7-S Layout Diagram NF7-M Layout Diagram NF7-S2/NF7-S2G, Ver Hardware Setup Install The MotherboardInstall CPU and Heatsink Chapter Install System Memory Valid Memory Configurations Bank Memory Module Total MemoryTotal System Memory for Un-buffered & Non-ECC DDR 400 Dimm Connectors, Headers and Switches ATX Power Input ConnectorsNF7/NF7-S/NF7-MNF7-S2/NF7-S2G FAN Connectors Pin 1-2 shorted default Normal operation Cmos Memory Clearing HeaderNF7/NF7-S/NF7-M NF7-S2/NF7-S2G NF7/NF7-S/NF7-M Wake-up HeaderNF7-S2/NF7-S2G Ver NF7/NF7-S/NF7-MNF7-S2/NF7-S2G Hled Pin 1 Front Panel Switches & Indicators HeadersRST Pin 5 SPK Pin 15, 17, 19Infrared Device Header NF7/NF7-S/NF7-M VCC Additional USB Port HeadersAdditional IEEE1394 Port Headers NF7-S Front Panel Audio Connection Header NF7-S2/NF7-S2G Internal Audio Connectors Accelerated Graphics Port Slot Floppy Disk Drive Connector IDE Connectors NF7-S2/NF7-S2G Serial ATA Connectors NF7-S/NF7-S2/NF7-S2G Status Indicators System Management Bus Headers Back Panel Connectors NF7/NF7-S NF7-M NF7-S2/NF7-S2G AUDIO1 Bios Setup EscF10 CPU Name Is SoftMenu SetupCPU Internal Frequency CPU Operating SpeedMultiplier Factor Power Supply ControllerAGP Frequency CPU FSB/DRAM ratioFrequency Brand NameSystem Performance FSB FrequencyRAS-to-CAS delay Row-active delayRow-precharge delay CAS Latency TimeStandard Cmos Features NF7/NF7-S/NF7-M NF7-S2/NF7-S2G Date mmddyyTime hhmmss Capacity NF7/NF7-S/NF7-M NF7-S2/NF7-S2G IDE HDD Auto-DetectionCylinder Floppy 3 Mode SupportHead PrecompExtended Memory Base MemoryAdvanced Bios Features Boot Up NumLock Status Boot Up Floppy SeekApic Mode Swap Floppy DriveDelay IDE Initial Report No FDD For OSFull Screen Logo Show NF7-S2/NF7-S2G System Bios Cacheable Advanced Chipset FeaturesAGP Aperture Size Video RAM CacheableFrame Buffer Size For NF7-M only FSB Spread SpectrumAGP Aperture Size MB AGP 8X SupportSpecial I/O for PCI Card Integrated Peripherals Master/Slave Drive PIO ModeOnChip IDE Device OnChip IDE1 ControllerOnChip IDE2 Controller IDE Prefetch ModeIDE Bus Master OnChip PCI DeviceAudio Controller LAN Boot ROMLAN Controller IEEE1394 Controller For NF7-S OnlyUse IR Pins IR Transmission DelayEXT-P2P’s Discard Time Onboard FDD ControllerEPP Mode Select Parallel1 Port ModeECP Mode Use DMA IDE Function SetupOnChip IDE-1/IDE-2 Controller Onboard DeviceSerial-ATA USB KB. Storage SupportSuperIO Device Sata Spread SpectrumInit Display First Power Management Setup Day of Month Alarm/ Time hhmmss Alarm Power-On by Alarm NF7-S2/NF7-S2GPower On Function KB Power On PasswordRestore on AC Power Loss Force Update Escd PnP/PCI ConfigurationsResources Controlled By IRQ ResourcesPCI/VGA Palette Snoop PCI Latency TimerAllocate IRQ to Video Allocate IRQ to USBAssign IRQ for VGA NF7-S2/NF7-S2GPirq 0 Assignment ~ Pirq 3 Assignment Assign IRQ for USBCPU Shutdown Temperature / Shutdown Temperature CPU Warning TemperaturePC Health Status Load Optimized Defaults Load Fail-Safe DefaultsSet Password Save & Exit SetupNF7 Series Appendix A. Install Nvidia nForce Chipset Driver Click Continue Anyway Appendix B. Install Integrated GPU Driver NF7-M Appendix B Appendix C. Install USB 2.0 Driver Appendix C Appendix D. Install LAN Driver NF7-S2G Appendix D Appendix E. Install Serial ATA Driver NF7-S Click Finish RAID Configuration Utility Menu Bios Setup for Serial ATA RAIDArray Mode Main MenuOption Delete RAID set Option Rebuild Mirrored setOption Resolve Conflicts Setting Up the Bios Appendix F. Bios Setup for Nvraid NF7-S2/NF7-S2GNvidia RAID Utility Menu Define a New ArrayAssinging the Disks Selecting the RAID ModeArray Detail Array ListNF7 Series Appendix G. Abit EQ The Hardware Doctor Utility Appendix G Appendix H. FlashMenu Bios Update Utility Appendix H Appendix I. Troubleshooting Need Assistance? Example Main instructions Technical Support Form Appendix J. How to Get Technical Support Alt.comp.hardware.homebuilt alt.comp.hardware.pc-homebuilt 4QX, UK Thank You Abit Computer Corporation

NF7, NF7-S2G, NF7-M, NF7-S2, NF7-S specifications

The Abit NF7 series of motherboards, which includes the NF7-S, NF7-S2, NF7-M, NF7-S2G, and NF7, is renowned for its performance, stability, and advanced features tailored for AMD processors during the early 2000s. These boards were particularly popular for enthusiasts and gamers seeking to build high-performance systems with the nForce2 chipset, which significantly enhanced system capabilities.

The NF7-S, the flagship model, stood out due to its comprehensive feature set. It supported a broad range of AMD processors, including the Athlon XP and Duron, which made it an appealing choice for various users. One of its main attractions was the dual-channel memory technology, permitting up to 2GB of DDR RAM, effectively doubling memory bandwidth and improving performance in memory-intensive applications.

Another significant feature of the NF7-S was its integrated Universal Audio Codec, delivering high-quality sound without the need for a separate sound card. Additionally, it offered a fast 133MHz FSB (Front Side Bus), enabling remarkable speed in data transfer, thereby enhancing the overall system performance. The motherboard also featured several expansion slots, including AGP 8x and PCI slots, allowing users to install a range of graphics cards and peripherals.

The NF7-S2, a slightly reduced version, maintained many capabilities of the NF7-S while providing essential features suitable for budget-conscious builders. It came with single-channel memory support but still leveraged the strengths of the nForce2 chipset, ensuring solid performance for general computing and light gaming.

The NF7-M was tailored for micro-ATX systems, representing a compact solution for those who needed a smaller footprint without sacrificing performance. With similar specs to its larger counterparts, it also supported dual-channel memory and offered significant connectivity options.

The NF7-S2G included integrated graphics capabilities, catering to users who preferred a more straightforward setup without dedicated graphics cards. This model offered a great balance for everyday computing tasks and casual gaming.

In summary, the Abit NF7-series motherboards were pivotal in advancing desktop performance during their time, providing users with robust options filled with innovative technologies and a variety of features designed for different needs, solidifying their legacy in the history of computer hardware.
Top Page Image Contents